Advertisement
15. SW1/2 LEV (Sweep 1/2 Level)
0 1 :
F G
S w e e p 1
These are the frequency mid-sweep levels, adjustable +/- 32 steps, equaling a boost/cut of 15dB.
16. SW1/2 FRQ (Sweep 1/2 Frequency)
0 1 :
F G
S w 1
F r q :
The lower frequency (SW1) mid-sweep frequency control, adjusts from 90 Hz - 4.4 kHz.
The higher frequency (SW2) mid-sweep frequency control, adjusting from 200 Hz - 9.5 kHz.
17. FG (Frank Gambale)
F 0 :
F G
Press to access Frank's 20 favorite patches. These are hardwired into the unit and cannot be
overwritten. You can save these patches into normal memory to add your own little tweaks.
These are also accessible as MIDI patch 100 - 119. To return to the user patches (01-99)
press the PROGRAM button and scroll to the left or right to get to 01 or 99.
18. EFF LEV (Effects Level)
0 1 :
F G
E f f 1 / 2
This adjusts the over-all effects level of both EFF1 and EFF2. This does not affect the external FX
loop levels. Push the button again to access the external Effects Loop SEND ON/OFF control,
0 1 :
F G
E x t .
then use theADJUST knob to turn it ON/OFF. Press the EFF LEV button again to return to
effects level.
19. EFF1 and EFF2
E f f e c t 1 : _ D e l a y
R e g e n : 1 5
There are two effect positions available(EFF1 and EFF2). Each slot may have any one of
the 4 effects (Reverb, Delay, Chorus, or Flange). The first push of one of these buttons
allows you to select what effect is in that slot by using the ADJUST knob. Push the button
again to move to the first parameter.
E f f e c t 1 :
D a m p : 0 9
Each push of the button scrolls through the parameters or effect selection.
E f f e c t 1 :
S p e e d : 0 4
Typical Setups
TN100
INTERNAL
FUSE
125VA
90-250 VAC
50-60HZ
SERIAL NUMBER
x x x x x x
MIDI
IN
THRU
OUTPUTS
–
+
+
1
www.carvin.com
DCM600
STEREO AMPLIFIER
8 OHMS/CH
225W
1
4 Ω Ω Ω Ω MIN
4 OHMS/CH
350W
BRIDGE ONLY
500W
2 OHMS/CH
8Ω Ω Ω Ω BRIDGED
700W
4Ω Ω Ω Ω BRIDGED
MADE
TH
SERIAL NUMBER
1000W
IN
E
US
A
120VAC 60Hz
1200VA INTERNAL FUSE
PIN 1+ POS, PIN 1- NEG, (PIN 2+ PIN 2- NOT USED)
1
2Ω Ω Ω Ω MIN
VE212 EXTENTION CAB
L e a d
1
L v l :
+ 1 2
L e a d
1
1 . 0
k H z
L e a d
1
L e a d
1
L e v e l :
2 3
L e a d
1
F X
L o o p : O N
T i m e : 3 1
R e v e r b
D e c a y : 1 8
F l a n g e
D p t h : 2 1
FS22 FOOTSWITCH
TN100
MADE
IN T HE
L
L
EFFECTS
US
A
L
ALTERNATE
LOOP
PHONES
SEND
R
R
RETURN
GND
FOOTSWITCH
LIFT
R
OUTPUT 1
+4
OUTPUT 2
+4
(MONO)
CABINET VOICED
TO MIXER INPUT R
TO MIXER INPUT L
DCM600
30-01500A
–
INPUTS
2
1
2
PIN 1 GND
PIN 2 SIGNAL +
XLR
PIN 3 SIGNAL –
BRIDGE
ON
OFF
LIMITER
GND
PARALLEL
LIFT
INPUTS
2
2
2Ω Ω Ω Ω MIN
VE212 EXTENTION CAB
All parameters have values 1 to 32.
Parameters for each effect are:
A) Reverb - Damping(amount of Presence) and Decay.
B) Delay - Regeneration(# of repeats) and Time.
C) Chorus - Reverb and Depth.
D) Flange - Speed and Depth.
E) Off - Mutes only that effect, 1 or 2.
REAR PANEL
20. AC INPUT
The preamp will accept power in the range of 90-250 VAC 50-60 Hz.
21. MIDI IN
This jack accepts all standard 5 pin DIN MIDI connectors. MIDI channel can be set to any
of the 16 MIDI channels through the UTILITY menu. MIDI phantom power is supplied as
+9V DC on pin 3 and ground on pin 1.
22. MIDI THRU
This is a hard-wired MIDI THRU. All input at the MIDI IN jack is sent out the MIDI THRU.
23. GND LIFT(GROUND LIFT)
Use this switch to help get rid of annoying ground loops in your system.
24. OUTPUT1 L (Left) and R (Right)(To Amp)
Both Balanced XLR jack and Unbalanced 1/4" jack outputs are provided for flexibility in
connecting up to your system.
25. +4
This switch allows you to switch between levels of +4 dB and -15 dB. Push it in if you need
the hotter +4 dB. Each switch applies to all the jacks in that section.
26. PHONES
Stereo headphone jack is filtered to tame the harsh high end. Its level is also controlled
by the OUTPUT2 sections +4 dB switch.
27. OUTPUT2 CABINET VOICED (DIRECT OUT)
This section is similar to OUTPUT1 however the signal is filtered to simulate the
response of a guitar speaker cabinet. This is great for going straight to a mixer for
recording or live sound.
28. RETURN L + R
Effects Loop return jacks are set up to return a stereo effect. If a Mono effect is used the
jacks will sum the signal equally to both sides. If a return to only one side is desired a spare
1/4" plug can be plugged into the unused return jack to break the connection.
29. SEND
The effects send signal is post Master Volume so any changes there must be accommodated
at your effects unit. The SEND signal may also be turned off through the Effect level button.
30. ALTERNATE INPUT
Great for plugging in your wireless rack-mount , or for keeping a clean look with no cables
on the front of your system. This plug is turned off if the front panel INPUT is used.
31. FOOTSWITCH FS22
Carvins standard FS22 footswitch can be used to switch patches UP and DOWN.
INTERNAL
1-800-854-2235
FUSE
www.carvin.com
125VA
90-250 VAC
INTERNAL FUSE
SERIAL NUMBER
50-60HZ
90-250 VAC
x x x x x x
10 VA
50-60Hz
TUNER
INPUT
FS22
INTERNAL
FUSE
125VA
90-250 VAC
SERIAL NUMBER
50-60HZ
x x x x x x
MADE
IN T HE
L
L
EFFECTS
TN100
FX-1
(MONO)
US
A
EFFECT 2
L
L
L
L
LOOP
DUAL STEREO PROCESSOR
PHONES
FOOTSWITCH
OUTPUT
INPUT
OUTPUT
R
R
RETURN
GND
SERIAL NUMBER
R
R
R
R
LIFT
MADE
IN THE
US
A
GND
OUTPUT 1
+4
OUTPUT 2
TIP - CH 2
+4
MIDI
(MONO)
IN
THRU
LIFT
CABINET VOICED
MADE
IN T HE
L
L
EFFECTS
TN100
US
A
L
LOOP
PHONES
R
R
RETURN
GND
LIFT
R
OUTPUT 1
+4
OUTPUT 2
+4
MIDI
IN
THRU
(MONO)
CABINET VOICED
EFFECTS
SEND
RETURN
FS22 FOOT
PHONES
SWITCH
MIDI FOOT-CONTROLLER
FX1
(MONO)
EFFECT 1
ALTERNATE
L
INPUT
FOOTSWITCH
SEND
INPUT
FOOTSWITCH
R
TIP - CH 1
FS22
RING - CH 2
TN100
ALTERNATE
INPUT
SEND
FOOTSWITCH
FS22
SX200 COMBO
VOICED
100 WATTS
LINE OUT
SPK
SPKRS
SW
1 x 4Ω Ω Ω Ω - 4Ω Ω Ω Ω
IMP
2 x 8Ω Ω Ω Ω - 4Ω Ω Ω Ω
1 x 8Ω Ω Ω Ω - 8Ω Ω Ω Ω
2 x 16Ω Ω Ω Ω - 8Ω Ω Ω Ω
1 x 16Ω Ω Ω Ω - 16Ω Ω Ω Ω
16Ω Ω Ω Ω
8Ω Ω Ω Ω
1
2
4Ω Ω Ω Ω
IMPROPER
SETTINGS
WILL RESULT
IN HI-TEMP
SPEAKER
PROTECTION!
OUTPUT
Advertisement
