Advertisement
CAUTION — TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY
GROUND ON THE POWER CORD. DO NOT REMOVE COVER.
WARNING — TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN
OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL.
SERIAL NUMBER
Press firmly until cord clicks in.
24
REAR PANEL FEATURES
20. MAIN OUT (EFFECTS SEND) JACK
The MAIN OUT jack is a post EQ output jack for pre amplifier signal access. This
output is the same signal that is being fed to the internal power amplifier. Use
this jack as your EFFECT SEND when using external effects. It will also drive an
external amp should you require more power.
21. EFFECTS RETURN (AMP IN) JACK
The EFFECTS RETURN jack is the input return jack that completes the effects
loop. This jack will interrupt the signal path when plugged into. Plug the output
of your external effects unit into this jack.
22. LINE OUT JACKS
The front LINE OUT control sets the output level of these jacks. They are fully
independent from the MASTER control.
The RIGHT / MONO-BAL jack is a MONO, balanced TRS (Tip-Ring-Sleeve) output
when used by itself. When a plug is inserted into the LEFT/UNBAL jack, the RIGHT
jack becomes a standard unbalanced output and you have a pair of stereo outputs.
The LINE OUT jacks are generally used to connect your amp to the main mixer.
23. EXTERNAL SPEAKER JACK (CHASSIS)
The EXTERNAL SPEAKER jack is for connecting additional speaker cabinets. The
jack is configured so an external speaker cabinet can be connected in series with
the KB100's internal speaker. Recommended external speaker impedances are 4
to 8 ohms. Carvin recommends the 112AG extension speaker.
24. AC POWER
The detachable AC POWER CORD supplied is designed to operate with one type
of voltage (the European 230V export model uses a CEE-7 plug cord set). Make
sure the cord is securely inserted into the back of the unit. Plug the cord into a
grounded "3" prong" power source. No attempt should ever be made to defeat
or use the amp without the ground connected. The internal switching power supply
will "auto-switch" from 100 VAC to 250 VAC, 50 to 60 Hz. This allows the KB100
to be used in various countries without the need for modifications or external trans-
formers.
25. 1/4" SPEAKER INPUT
A 1/4" jack is used for connecting the amp to the speaker cabinet.
26. 1" TITANIUM HF DRIVER L-PAD
The rear HF Driver L-Pad adjusts the level of the HF Driver to give crisp clear
highs. If distortion is heard when playing excessively loud, turn the HF Driver
down as it can amplify distortion.
Rear Enclosure
HF Driver L-Pad
26
STEREO SETUP USING TWO KB100'S
OR ONE ADDITIONAL POWER AMP & SPEAKER:
MASTER AMP(RIGHT)
LINE OUT
MAIN OUT
LEFT
RIGHT
EFFECT SEND
UNBAL
MONO-BAL
MONO
EFFECT
MAIN
AUX
SPEAKER
SPEAKER
RETURN
(AMP IN)
8 OHM
8 OHM
MIN.
MIN.
The KB100 is capable of stereo operation if another amp is available.
Connect the RIGHT LINE OUT jack to the AMP IN (EFFECT RETURN) of the amp
you have your instruments connected to. Use the LEFT LINE OUT jack to con-
nect to the INPUT of a seperate power amp, or to the AMP IN (EFFECT RETURN)
of another KB100 unit. ( NOTE: GRAPHIC EQ will not function )
20
22
21
23
25
SLAVE/POWER AMP(LEFT)
LINE OUT
MAIN OUT
LEFT
RIGHT
EFFECT SEND
UNBAL
MONO-BAL
MONO
EFFECT
MAIN
AUX
SPEAKER
SPEAKER
RETURN
(AMP IN)
8 OHM
8 OHM
MIN.
MIN.
Advertisement
