NEC MultiSync PA242W User Manual page 26

2
HOT KEY*
FACTORY PRESET*
Tag8 PIP MODE
PIP INPUT
PIP LEFT/RIGHT
PIP DOWN/UP
PIP SIZE
BLANK SIGNAL SKIP Skip no signal inputs when you change input signal with INPUT button.
OSD ROTATION
MAIN IMAGE
ROTATION
SUB IMAGE
ROTATION
DDC/CI
SCREEN SAVER
Tag9* INPUT SETTING*
(Analog
input only)
* Only for PA242W.
2
* This item does not reset by FACTORY PRESET (Tag7).
When this function is activated; the brightness of the monitor can be adjusted without
entering the OSD menu by using the front buttons.
The "LEFT" or "RIGHT" buttons adjust the brightness level.
When this function is set to OFF, some buttons are disabled. See page 11.
2
Selecting FACTORY PRESET allows you to reset all OSD control settings back to the
factory settings. Highlighting the control to be reset and pressing the RESET button can
reset individual settings.
Selects PIP MODE, OFF/PIP/PICTURE BY PICTURE - ASPECT/PICTURE BY
PICTURE - FULL. See page 14.
Selects the PIP input signal.
When you select "PIP" in PIP MODE, you can control horizontal position of PIP display area.
When you select "PIP" in PIP MODE, you can control vertical position of PIP display area.
Selects the size of the sub-picture used in PIP MODE.
AUTO: The OSD rotates automatically when the monitor is rotated. OSD ROTATION is
set to AUTO by default.
LANDSCAPE: Display the OSD with landscape mode.
PORTRAIT: Display the OSD with portrait mode.
AUTO: The main window image automatically rotates according to the orientation of the
display.
OFF: The main window image is not rotated. MAIN IMAGE ROTATION is set to OFF by
default.
ON: The main window image always rotated.
Note: For PA272W/PA302W, this function is effective only if PICTURE BY PICTURE-
ASPECT or PICTURE BY PICTURE-FULL.
AUTO: The sub window image automatically rotates according to the orientation of the
display.
OFF: The sub window image is not rotated. SUB IMAGE ROTATION is set to OFF by
default.
ON: The sub window image always rotated.
DDC/CI ENABLE/DISABLE: Turns on or off the two way communication and control with
connected PC by video cable.
NOTE: Set DDC/CI to ENABLE when using hardware calibration software like
MultiProfi ler over DisplayPort, DVI or VGA.
Use the SCREEN SAVER to reduce the risk of image persistence.
MOTION (Default OFF): Screen image moves periodically in 4 directions in order to
reduce the risk of image retention.
Timing for MOTION can be set so the screen image moves in intervals from every
10 to 900 seconds. Timing is set in 10-second increments.
OPTION (Default REDUCED): There are two optional selections.
REDUCED: Screen image is reduced to 95% size and is moved periodically in
4 directions. Screen may appear slightly less sharp than normal. The full image appears
on the display.
NOTE: Some input signals may not be supported by REDUCED.
FULL: Screen image is set to FULL and is moved periodically in 4 directions. Screen
image goes outside of the display area in the direction that it shifts so that a portion of the
image may appear to be cut off.
NOTE: SCREEN SAVER works when ENABLE is OFF in TILE MATRIX and PIP MODE
is OFF.
2 Video Band Width: Reduce the visual "noise" level of the input signal. It is strong
ineffective, so that a number becomes small. Press "LEFT" or "RIGHT" to select.
Sync Threshold: Adjusts the slice level of a synchronization signal. Press "SELECT" to
move the adjustment menu. Adjusts the sensitivity of the separate or composite input
signals.
Try this option if the FINE adjustment does not successfully eliminate the noise.
Clamp position: Operating your monitor at a non-standard timing may cause images to
appear darker than normal or have color distortion. Use of the Clamp position control will
adjust images to their normal state.
English-24