VF 411-610 Important safeguards Page 3 1. Important Notes Page 4-5 For your safety Page 4 About use Page 5 Operating for the first time Page 5 2. Features Page 6 Features Page 6 Special accessories Page 6 3. Operation...
Page 4
Congratulations on buying your new “Vario” appliance. Before switching your appliance on for the first time, we would like you to familiarize yourself with your new appliance. In this manual you will find important notes on safety and operation. These will serve to ensure your personal safety and the lasting value of your appliance.
Important safeguards Read All Instructions. i) Never Leave Surface Units Unattended at High Heat Settings – Boilover causes smoking and greasy spillovers that may ignite. 2. To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage k) Use extreme caution when moving the grease space located above the surface units should be kettle or disposing of hot grease.
1. Important Notes For your safety Do not operate the appliance if it is damaged. If a fire should break out, switch off the elec- tricity at fuse point and close the appliance The appliance must only be connected by cover.
The appliance must not be operated empty. If the please inform your specialist dealer or your nearest appliance is switched on empty, the temperature Gaggenau after-sales service. control will switch off the appliance automatically. Turn the “Temperature" control knob to the OFF position.
2. Features Features 1 Appliance cover 2 Holding clip for frying basket holder 3 Frying basket holder 4 Minimum / maximum level marker 5 Foaming edge 6 Heating element (3 000 W) 7 Control knob to select fat / oil / cleaning setting 8 Temperature control knob Special accessories You can order the following special accessories:...
Any water contained in the food sinks to the bottom of the Gaggenau Electric Fryer into so-called cold oil zone. This prevents the oil frothing over. Also, any particles of food which break away during frying fall through the basket and sink to this cold zone.
Switching on Important: Never switch on the deep fryer • Open the appliance cover. Fit the frying basket empty. The oil/fat level in the frying basin should holder into the two clips on the edge of the basin always be between the two marking lines. and secure the holder in the clamp on the cover.
Switching off Switching off Fully turn the right control knob to the OFF position. Residual heat display After switching off the deep fryer, the luminous disc behind the right control knob will flash, as long as the appliance has not cooled down sufficiently to be touched safely.
Visual signals Luminous disc Luminous disc Signification Cause / Remedy behind the left behind the right control knob control knob lights OFF appliance is switched OFF right control knob appliance is ON normal use lights constantly flashing of appliance is normal use right control knob heating up...
4. Practical tips • The deep frying temperature range lies between • If you would like to re-use the oil, filter the cooled 320 and 360 °F . The maximum temperature is oil through a fine metal sieve. 380 °F . •...
6. Cleaning and care • Press down both control knobs and turn them right Note: to avoid jeopardising the electrical safety to the cleaning setting. The luminous disc behind of the appliance, do not use high-pressure or the right control knob flashes, as long as the steam jet cleaning devices –...
If the power supply is functioning correctly, but your appliance still does not work, please contact your Gaggenau dealer who will provide you with the address and telephone number of your nearest manufacturer’s authorized service agent or contact Gaggenau USA on (800) 828-9165.
Total connected load: 3 000 W AC 208/220-240 V / 60 Hz Important notes on installation This appliance can be combined with all Gaggenau There must be a gap of at least 40 mm (1 ´ ´ ) at Vario 400 Series appliances.
Preparing the cabinet The minimum spaces that must be maintained between the appliance cooking surface and the horizontal surface above the cooking top shall be: A = 30 inches (762 mm) minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet;...
Preparing the cabinet • Cut out the recess for one or several Vario appliances in your worktop. Proceed as indicated on the installation sketch. The installation sketch contains the measurements of the space required for the trim between the appliances. Several appliances can also be installed in individual recesses, as long as a minimum clearance of 50 mm (2 ´...
Installing the control panel Note: only install control panel with appliance of the corresponding type. Before connecting the appliance, make sure the electricity is switched off at fuse point! • Before installation, remove all styrofoam packaging from the control knobs and peel off the protective film behind the luminous discs.
Installing the appliance • Firmly plug the connecting cable in the appliance and in the control panel (the plugs must lock into place). • Turn the clamping screws to the side. Insert the appliance with the control panel on the front into the cut-out and align it.
Page 24
GAGGENAU HAUSGERÄTE GMBH 5551 McFADDEN AVENUE CARL-WERY-STR. 34 · 81739 MÜNCHEN HUNTINGTON BEACH, CA 92649 GERMANY Y (0 89) 45 90 - 03 Y (800) 828-9165 · FAX (714) 901-0979 FAX (0 89) 45 90 - 23 47 www.gaggenau-usa.com...