Table of Contents
Advertisement
Quick Links
Rotating & oscillating effect ensures
exceptional finishing results.
Precision ground cast iron table.
On-board side mounted spindle storage.
Tilting table for sanding beveled parts.
2" diameter dust outlet with 2" to 4"
adapter fitting included.
5 interchangeable spindle assemblies:
1/4", 1/2", 5/8", 1 1/2", 2" dia.with 100 grit
sand paper.
1 1/2" & 2" spindles come with rubber
drums.
Includes 4 table inserts to accomodate
different spindle sizes.
OSCILLATIONS PER MINUTE
29
LENGTH OF OSCILLATION
15⁄16" (24 mm)
TABLE SIZE
14 1⁄2" x 14 1⁄2" (368 x 368 mm)
TABLE TILT
0° - 45°
TABLE HEIGHT FROM BOTTOM OF BASE
18 5⁄16" (465 mm)
SPINDLE SIZES
1⁄4" TO 2" (6.2 TO 50.8 mm)
DUST CHUTE OUTLET
2" (50.8 mm)
SPINDLE SPEED
1720 RPM
BASE DIMENSIONS (L x W
14 1⁄2" x 14 1⁄2" (368 x 368 mm)
MOTOR
1⁄2 HP , 110 V, 7.5 A
WEIGHT
81 LBS (37 kg)
REVISION 3 FEB 13/07
© COPYRIGHT GENERAL INTERNATIONAL 02/2007
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for General 15-220
Summary of Contents for General 15-220
- Page 1 Rotating & oscillating effect ensures exceptional finishing results. Precision ground cast iron table. On-board side mounted spindle storage. Tilting table for sanding beveled parts. 2” diameter dust outlet with 2” to 4” adapter fitting included. 5 interchangeable spindle assemblies: 1/4", 1/2", 5/8", 1 1/2", 2" dia.with 100 grit sand paper.
- Page 2 The manual’s purpose is to familiarize you with the safe operation, basic function, and features of this oscillating spindle sander as well as the set-up, maintenance and identification of its parts and components. This manual is not intended as a substitute for formal woodworking instruction, nor to offer the user instruction in the craft of woodworking.
-
Page 3: Rules For Safe Operation
22. Avoid working from awkward or off balance positions. Do not overreach and always keep both feet firmly on the floor. 23. Do not use this spindle sander for other than it’s intended use. If used for other purposes, GENERAL® INTERNATIONAL disclaims any real or implied warranty and holds itself harmless for any injury, which may result from that use. -
Page 4: Electrical Requirements
ELECTRICAL REQUIREMENTS Before connecting the machine to the power source, ver- ify that the voltage of your power supply corresponds with the voltage specified on the motor I.D. nameplate. A power source with greater voltage than needed can result in serious injury to the user as well as damage to the machine. -
Page 5: Identification Of Main Parts And Components
VERTICAL OSCILLATING SPINDLE SANDER 15-220 IDENTIFICATION OF MAIN PARTS AND COMPONENTS ACCESSORY STORAGE BASE CAST-IRON TABLE SWITCH ASSEMBLY TABLE INSERT TABLE TILT LOCK LEVER SANDING SPINDLE... -
Page 6: Unpacking And Setup
UNPACKING AND SET-UP SET UP SAFETY Serious personal injury could occur if you con- nect the machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so. The MODEL 15-220M1 is a heavy machine (81 lbs shipping weight–37kg). -
Page 7: Assembly Instructions
CLEAN UP Be sure to work in a well ventilated area for the entire clean up process. All unpainted surfaces are covered with a protective coating that prevents rust from forming during shipping and storage. Peel off the plastic cover from the table and remove this protective coating by rubbing with a rag dipped in kerosene, mineral spirits or paint thinner. - Page 8 INSTALL THE SANDING SLEEVES ONTO THEIR CORRESPONDING SPINDLES Step 1 For 1/4, 1/2, & 5/8 spindles loosen the screw on the bracket clamp ( ) at the bottom of the spindle. Step 3 Double check that the sleeve is now on the spindle securely by pulling on the sleeve to make sure it does not slide off the spindle.
-
Page 9: Accessory Storage
ACCESSORY STORAGE SPINDLES Place the drums into their storage space on the right side of the machine. INSTALLING SPINDLES ON THE MACHINE Note: Reverse threads are used to attach the spindle to the machine. Make sure that the switch is in “OFF” position and that the power cord is unplugged. If installed, remove the table insert to allow better access the spindle seat. -
Page 10: Recommended Adjustments
SELECTION GUIDE FOR TABLE INSERTS This machine is supplied with 5 spindles, and four table inserts. The spindle diameters range from 1/4" to 2". When changing spindles, the table insert will need to be changed to the matching size. Each plate has notch ( ) to fit the alignment pin ( ensure that it is properly fitted and installed in the table... -
Page 11: Changing Sanding Sleeves
90° TABLE STOP ROD Step 3 If the table needs adjustment loosen both lock levers and readjust the table position until the square is flat against the table and the sanding drum. To allow for more or less rear tilt adjust the table stop rod as needed. -
Page 12: Operating Instructions
When you have finished using the machine be sure to re-install the lock-out pin and unplug the machine from the power source. Always turn on the dust collector before starting the sander and always stop the sander before turning off the dust collector. (not included). (not included). -
Page 13: Basic Operations
BASIC OPERATIONS Before operating this machine, make sure you have read this manual attentively! Failure to read and understand the instructions, warnings and safe- ty guidelines provided in this manual may lead to serious injury and / or damage to machine or the workpiece. - Page 14 OSCILLATING SPINDLE SANDER We offer a large variety of products to help you increase pro- ductivity, accuracy and safety when using your oscillating spin- dle sander. Here’s a small sampling of accessories available from your local General International dealer. Stand...
-
Page 16: Parts List
30203001 15220-45 30203003 15220-46 30203003A 15220-47 S0020825M 15220-48 30300028 15220-49 S0110600 15220-50 40501011 PARTS LIST 15-220 DESCRIPTION BASE TOP PLATE STRAIN RELIEF POWER CORD PHILLIPS HEAD SCREW RUBBER FOOT WASHER LOCK NUT LOCK WASHER PHILLIPS HEAD SCREW MOTOR SET SCREW... - Page 17 WG000002 SWITCH BOX 15220-96 WG000003 SAFETY LOCK-OUT PIN W/CHAIN 15220-97 2” TO 4” DUST HOSE ADAPTOR PARTS LIST 15-220 SPECIFICATION (LEFT) M6 X 1.0 X 6L 1/4" M5 X 0.8-10L 22 X 119 M5 X 0.8-8L 5 X 5 X 50 2"...
- Page 18 15-220 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax : (514) 326-5565 Parts & Service Fax : (514) 326-5555 Order Desk orderdesk@general.ca www.general.ca IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity...
Need help?
Do you have a question about the 15-220 and is the answer not in the manual?
Questions and answers