Denon AVR-4810 Owner's Manual page 46

ENGLISH
Making Detailed Settings (Manual Setup)
Setting items
Channel Level Default : Reset all distance settings to factory default.
(Continued) • Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover Frequency 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
Outputs at below set 250Hz : Set the crossover frequency.
frequency, each speaker's
Advanced : Specify crossover frequency for each speaker.
bass signal output from
• Front / Center / Surround / Surround Back / Front Height / Front
the subwoofer. Set this
Wide : Select the speaker.
according to the low
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
frequency reproduction
250Hz : Set the crossover frequency.
capabilities of the speakers
you are using.
• Can be set when the "Speaker Configuration" – "Subwoofer" (vpage
40) setting is "Yes", or when you have a speaker that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
• The speakers that can be set when "Advanced" is selected differ
according to the "Subwoofer Mode" setting (vpage 41).
• When "LFE" is selected, speakers set to "Small" at "Speaker
Configuration" can be set. If the speakers are set to "Large", "Full
Band" is displayed and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
Speaker Impedance 8Ω/ohms : Select when the impedance of the connected speaker is 8
Set the impedance of Ω/ohms or more.
connected speakers. 6Ω/ohms : Select when the impedance of the connected speaker is at
least 6 Ω/ohms but less than 8 Ω/ohms.
Check the speaker impedance (Ω) shown on the back of your speakers
or in the instruction manual beforehand.

Main remote control unit
operation buttons
Setting contents
:Displaying the menu
Cancel the menu
Making the HDMI Settings (HDMI Setup)
Make settings for HDMI video/audio output.
Setting items
RGB Range Normal : Output with RGB video range (16 (black) to 235 (white)).
Set the video range of RGB Enhanced : Output with RGB video range (0 (black) to 255 (white)).
output from the HDMI
This setting is valid when using a TV equipped with a DVI terminal.
terminal.
Vertical Stretch ON : Expand image signal in vertical direction.
Expand image signal in OFF : Do not expand signal in vertical direction.
vertical direction.
This setting is valid with respect to the HDMI output when using an
HDMI-compatible TV. When not using an HDMI-compatible TV, it is
valid with respect to the analog output.
Auto Lip Sync ON : Compensated.
Automatic compensation OFF : Not compensated.
for timing shift in audio and
video output.
Amp : Playback through speakers connected to the receiver.
HDMI Audio Out
Select HDMI audio output TV : Playback through TV connected to the receiver.
device.
When the HDMI control function is operating, the setting of audio
playback in the connected TV takes priority (vpage 90 "HDMI
Control Function").
Monitor Out Auto (Dual) : The presence of a TV connected to the MONITOR 1 or
Make settings for HDMI MONITOR 2 terminal is detected automatically, and that TV connection
monitor output. is used.
Monitor 1 : A TV connected to the MONITOR 1 terminal is always used.
Monitor 2 : A TV connected to the MONITOR 2 terminal is always used.
• If both the Monitor 1 and 2 connectors are connected and "Resolution"
(vpage 60) is set to "Auto", the signals are output with a resolution
compatible with both TV.
• With "Resolution" (vpage 60) not set to "Auto", check whether
the TV you are using is compatible with the resolution under "HDMI
Information" – "Monitor 1" and "Monitor 2" (vpage 87).
• Depending on the monitor you have connected, the display may not be
correct when you set to "Auto (Dual)". In such a case, set to either
"Monitor 1" or "Monitor 2".
• You can also set "Monitor Out" by pressing
control unit.
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Default settings are underlined.
Setting contents
M.SEL
on the main remote
:Return to previous menu