Hdmi Setup - Denon AVR-1611 Owner's Manual

ENGLISH
Manual Setup
Setting items
Channel Level Test Tone Start : Output test tone.
Set the volume of the test • FL / C / FR / SR / SBR
tone to be the same when it speaker.
is output from each speaker. z When the "Speaker Config." – "S.Back" setting (vpage 49) is set to
"1sp", "S.Back" is displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• When
"Subwoofer" setting switches to "OFF".
• When "Channel Level" is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 33.
NOTE
• Speakers set to "None" in the "Speaker Config." (vpage 48) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Channel Level" is not displayed.
Default : The "Channel Level" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover Frequency Crossover : Set the crossover frequency.
Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output
250Hz
from each channel to
Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
• Front / Center / Surround / S.Back / Front Height : Select the speaker.
Crossover Frequency to
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
suit the bass reproduction
250Hz : Set the crossover frequency.
capability of the speaker
being used.
• "Crossover Frequency" can be set when the "Bass Setting" –
"Subwoofer Mode" (vpage 49) setting is "LFE+Main", or when you
have a speaker that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Advanced" is selected differ
depending on the "Subwoofer Mode" setting (vpage 49).
• When "LFE" is selected, speakers set to "Small" at "Speaker Config."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
50
Remote control operation
buttons
Setting details
z / SBL z / SL / FHL / FHR / SW : Select the
o is pressed while the subwoofer volume is set to "–12 dB", the
Move the cursor
(Up/Down/Left/Right)

HDMI Setup

Make settings for HDMI video/audio output.
Setting items
Auto Lip Sync ON : Compensated.
Make automatic OFF : Not compensated.
compensation for timing
shift in audio and video
output.
HDMI Audio Out Amp : Play back through speakers connected to the receiver.
Select HDMI audio output TV : Play back through TV connected to the receiver.
device.
When the HDMI control function is activated, priority is given to the TV
audio setting (vpage 32 "HDMI control function").
HDMI Control ON : Use HDMI control function.
You can link operations with OFF : Do not use HDMI control function.
devices connected to HDMI
and compatible with HDMI
• When a device that is not compatible with the HDMI control function is
Control.
connected, set "HDMI Control" to "OFF".
• Please consult the operating instructions for each connected component
to check the settings.
• Refer to "HDMI control function" (vpage 32) for more information about
the HDMI control function.
NOTE
• When "HDMI Control" is set to "ON", it consumes more standby
power. If you are not using this unit for an extended period, it is
recommended that you unplug the power cord from the power outlet.
• "HDMI Control" does not work when the power to the equipment is off.
Either turn power on or set to standby.
• The HDMI control function controls operations of a TV that is compatible
with the HDMI control function. Make sure that the TV and HDMI are
connected when you perform HDMI control.
• If the "HDMI Control" settings have been changed, always reset the
power to connected devices after the change.
Standby Source Last : This item is set at the last-used input source.
Sets the HDMI input source HDMI1 / HDMI2 / HDMI3 / HDMI4 : Put the respective input source into
to put into standby when standby.
the power is on.
"Standby Source" can be set when "HDMI Control" is set to "ON".
Power Off Control All : If power to a connected TV is turned off independently of the input
Links the power standby source, power to this unit is automatically set to standby.
of this unit to external Video : If power to a connected TV is turned off when the input source
equipment. is BD / DVD / TV / SAT/CBL / GAME / V.AUX / DOCK, power to this unit is
automatically set to standby.
OFF : This unit does not link with power to a TV.
"Power Off Control" can be set when "HDMI Control" is set to "ON".
Confirm the setting
Default settings are underlined.
Setting details
Return to previous menu