Hdmi Setup - Denon AVR-791 Owner's Manual

HDMI Setup

Make settings for HDMI video/audio output.
Setting items
Auto Lip Sync ON : Compensated.
Make automatic OFF : Not compensated.
compensation for timing
shift in audio and video
output.
HDMI Audio Out Amp : Play back through speakers connected to the receiver.
Select HDMI audio output TV : Play back through TV connected to the receiver.
device.
When the HDMI control function is activated, priority is given to the TV
audio setting (vpage 34 "HDMI control function").
HDMI Control ON : Use HDMI control function.
You can link operations with OFF : Do not use HDMI control function.
devices connected to HDMI
and compatible with HDMI
• When a device that is not compatible with the HDMI control function is
Control.
connected, set "HDMI Control" to "OFF".
• Please consult the operating instructions for each connected component
to check the settings.
• Refer to "HDMI control function" (vpage 34) for more information about
the HDMI control function.
NOTE
• When "HDMI Control" is set to "ON", it consumes more standby
power. If you are not using this unit for an extended period, it is
recommended that you unplug the power cord from the power outlet.
• "HDMI Control" does not work when the power to the equipment is off.
Either turn power on or set to standby.
• The HDMI control function controls operations of a TV that is compatible
with the HDMI control function. Make sure that the TV and HDMI are
connected when you perform HDMI control.
• If the "HDMI Control" settings have been changed, always reset the
power to connected devices after the change.
Standby Source Last : This item is set at the last-used input source.
Sets the HDMI input source HDMI1 / HDMI2 / HDMI3 / HDMI4 : Put the respective input source into
to put into standby when standby.
the power is on.
"Standby Source" can be set when "HDMI Control" is set to "ON".
Power Off Control All : If power to a connected TV is turned off independently of the input
Links the power standby source, power to this unit is automatically set to standby.
of this unit to external Video : If power to a connected TV is turned off when the input source
equipment. is BD / DVD / TV / SAT/CBL / GAME / V.AUX / DOCK, power to this unit is
automatically set to standby.
OFF : This unit does not link with power to a TV.
"Power Off Control" can be set when "HDMI Control" is set to "ON".
Remote control operation
buttons
Default settings are underlined.
Setting details
Move the cursor
(Up/Down/Left/Right)
Audio Setup
Make settings for audio playback.
Setting items
2ch DIRECT/STEREO Setting : Select the method for setting the speakers used in the 2-channel
Select the method for direct and stereo playback modes.
setting the speakers used • Basic : The settings at "Speaker Setup" (vpage 52) are applied.
in the 2-channel direct and • Custom : Make separate settings for 2-channel. Make the following
stereo playback modes. settings:
Front : Set the front speaker size.
• Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Config." – "Subwoofer" (vpage 52) is set to "No", the
setting is automatically set to "Large".
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
If "Speaker Config." – "Subwoofer" (vpage 52) is set to "No", the
setting is automatically set to "No". If the "Front" setting is "Small",
the setting is automatically "Yes".
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
• LFE : When the "2ch DIRECT/STEREO" – "Front" setting is set to
"Large", the LFE signal alone is output from the subwoofer. Also, when
the "2ch DIRECT/STEREO" – "Front" setting is set to "Small", the front
channel low range signal is added to the LFE signal output from the
subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made "2ch DIRECT/STEREO" – "Subwoofer"
is set to "Yes".
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• This setting can be set made "2ch DIRECT/STEREO" – "Subwoofer" is
set to "Yes".
• If the "2ch DIRECT/STEREO" – "Front" setting is "Large" and the
"Subwoofer Mode" setting is "LFE", "Full Band" is displayed and the
setting cannot be made.
Confirm the setting
ENGLISH
Manual Setup
Default settings are underlined.
Setting details
55
Return to previous menu