Page 1 LFD DISPLAY User Manual UD46C UD55C The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. BN46-00332A-06...
Page 2: Table Of Contents
Table of contents Before Using the Product Installing the Wall Mount Connection Using an HDMI-DVI Cable Preparing before installing Wall-Mount Connection Using an HDMI Cable Copyright Installing the Wall Mount Kit Connecting to an Audio System Wall Mount Kit Specifications (VESA) Safety Precautions Connecting an External Monitor Symbols...
Page 3 Table of contents Network Status Sound Adjustment Black Tone System Setup Flesh Tone Wi-Fi Direct Tool Settings RGB Only Mode Other Functions Color Space Soft AP Group Management White Balance AllShare Settings Schedule Management 10p White Balance Troubleshooting Guide Gamma Device Name Expert Pattern Motion Lighting...
Page 4 Source AutoSwitch Settings Source AutoSwitch Videos Primary Source Recovery Playing a Video Support Primary Source Photos Secondary Source Software Update Viewing a Photo (or Slide Show) General By USB Music Max. Power Saving Alternative Software Playing Music Game Mode Contact Samsung...
Page 5 Supported Video Formats Content Manager Settings When Content is Running Appendix MagicInfo Lite Contact SAMSUNG WORLD WIDE File Formats Compatible with MagicInfo Lite MagicInfo Videowall S Responsibility for the Pay Service (Cost to Player Customers) Read before using MagicInfo Lite Player...
Page 6: Before Using The Product
© 2013 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Microsoft, Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Page 7: Safety Precautions
Safety Precautions Cleaning ― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ― Take the following steps when cleaning. Caution ― The following images are for reference only. Real-life situations may differ from what is shown in the images.
Page 8: Storage
Storage Connect the power plug to a grounded power socket (type 1 insulated devices only). High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used • An electric shock or injury may result. nearby. ―...
Page 9: Installation
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. • A fire may result. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. • A fire or electric shock may result.
Page 10 SAMSUNG • Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
Page 11: Operation
If the product is dropped or the outer case is damaged, turn off the power Do not lift or move the product by pulling the power cord or any cable. switch and disconnect the power cord. Then contact Samsung Customer Service Center.
Page 12 • Your eyesight may deteriorate. when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center. • Product failure, an electric shock or fire may result. Do not hold the product upside-down or move it by holding the stand.
Page 13 Rest your eyes for more than 5 minutes for every 1 hour of product use. When replacing the battery, insert it with the right polarity (+, -). • Eye fatigue will be relieved. • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Page 14: Preparations
Chapter 02 Preparations Checking the Contents Cut the strap and open the box. Removing the Packaging ― The following images are for reference only. Real-life situations may differ from what is shown in the images. Remove the protective packaging from the box. Separate the box from the product.
Page 15: Checking The Components
Checking the Components - Contact the vendor where you purchased the product if any Components components are missing. - The appearance of the components and ― Components may differ in different locations. items sold separately may differ from the image shown. - A stand is not provided with the product.
Page 16: Items Sold Separately
Items sold separately - The following items can be purchased at your nearest retailer. DVI cable (P.42) Wall-mount Kit Stand RS232C cable (P.54) HDMI-DVI cable (P.43) DP cable (P.43) HDMI cable (P.43) Video cable (P.46) Stereo cable (P.23) Component cable (P.46) RCA stereo cable (P.48) RCA cable (P.47) AV/Component adapter (P.47)
Page 17: Parts
Parts Buttons Description Aim the remote control towards this spot on the LCD Display. Remote Control ― Keep the area between the remote sensor and remote control obstacle-free. Sensor External sensor KIT Automatically detects the intensity of ambient light around a selected display and Light sensor adjusts the screen brightness.
Page 18: Reverse Side
Port Description Reverse Side IR OUT Receives the remote control signal via the external sensor board and outputs the ― The color and shape of parts may differ from what is shown. Specifications are signal via LOOP OUT. subject to change without notice to improve quality. CONTROL IN Supplies power to the external sensor board or receives the light sensor signal.
Page 19: Attaching The Holders
Attaching the holders Anti-theft Lock ― An anti-theft lock allows you to use the product securely even in public places. ― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. To lock an anti-theft locking device: Fix the cable of your anti-theft locking device to a heavy object such as a desk.
Page 20: Remote Control
Remote Control ― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled. Power off the product. Power on the product. Number buttons Enter the password in the OSD menu. Mute the sound.
Page 21 TOOLS INFO Quickly select frequently used functions. Display information about the current input source. Move to the upper, lower, left or right menu, or adjust an option's setting. Confirm a menu selection. RETURN EXIT Exit the current menu. Return to the previous menu. Manually select a connected input source from HDMI PC, DVI, HDMI, or DP.
Page 22 Adjusting the OSD with the Remote Control Remote Control Reception Range Buttons Description Open the OSD menu. Select from Picture, Network, System Support the displayed OSD menu screen. Use the remote control within 7m to 10m from the sensor on the product at an angle of 30 from the left and right.
Page 23: Connection Using An Ir Stereo Cable (Sold Separately)
Connection Using an IR Stereo Cable (sold separately) ― Turn off the device before connecting the External Sensor Kit. After it is connected, turn on the device. Controlling more than one display product using IR OUT CONTROL IN your remote control •...
Page 24: Before Installing The Product (Installation Guide)
Tilting Angle and Rotation 15 ˚ ― Contact Samsung Customer Service Center for further details. • The product can be tilted at a maximum angle of 15 from a perpendicular wall surface. • To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Page 25: Dimensions
Figure 1.3 Top view Installation on an Indented Wall ― Contact Samsung Customer Service Center for further details. Plane view Minimum 40 mm Minimum 70 mm Minimum 50 mm Minimum 50 mm Ambient temperature: Under 35 C ― When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C.
Page 26: Installing The Wall Mount
We recommend you contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
Page 27: Wall Mount Kit Specifications (Vesa)
Samsung is not liable for these kinds of accidents. • Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
Page 28: Remote Control (Rs232C)
Remote Control (RS232C) • Pin assignment 1 2 3 4 5 Cable Connection RS232C Cable Interface RS232C (9 pins) 6 7 8 9 TxD (No.2), RxD (No.3), GND (No.5) Signal Bit rate 9600 bps Detect data carrier Data bits 8 bit Received data Parity None...
Page 29: Lan Cable
LAN Cable • RS232C cable Connector: 9-Pin D-Sub • Pin assignment Cable: Cross cable 1 2 3 4 5 6 7 8 -P1- -P1- -P2- -P2- Female --------> Female Pin No Standard Color Signal <-------- ---------- White and orange Orange White and green Blue White and blue...
Page 30 Cross LAN cable (PC to PC) • Connector : RJ45 Direct LAN cable (PC to HUB) RJ45 MDC RJ45 MDC RJ45 MDC Signal Signal <--------> <--------> Signal Signal <--------> <--------> <--------> <--------> <--------> <-------->...
Page 31: Connection
Connection • Connection 2 • Connection 1 RJ45 MDC RJ45 MDC RS232C RS232C RS232C RS232C • Connection 3 RJ45 RS232C RS232C RS232C RS232C...
Page 32: Control Codes
Command type Command Value range Control Codes Video Wall On 0x84 Viewing control state (Get control command) Video Wall User Control 0x89 Header Command Data length Checksum • All communications take place in hexadecimals. The checksum is calculated by adding up all 0xAA Command type values except the header.
Page 33: Power Control
Power control Volume control • Function • Function A product can be powered on and off using a PC. The volume of a product can be adjusted using a PC. • Viewing power state (Get Power ON / OFF Status) •...
Page 34 Input source control 0x24 HDMI2_PC • Function 0x25 DisplayPort The input source of a product can be changed using a PC. ― DVI_video, HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only respond to • Viewing input source state (Get Input Source Status) "Get"...
Page 35 Screen mode control Header Command Data length Ack/Nak r-CMD Val1 Checksum • Function 0xAA 0xFF 0x18 "ERR" The screen mode of a product can be changed using a PC. Screen mode cannot be controlled when the Video Wall function is enabled. "ERR": A code showing what error has occurred ―...
Page 36 PIP On/Off control Auto adjustment control (PC and BNC only) • Function • Function The PIP mode of a product can be turned on or off using a PC. Automatically adjust the PC system screen using a PC. ― Only available on models that have the PIP function. •...
Page 37 Video Wall Mode Control Safety Lock • Function • Function Video Wall mode can be activated on a product using a PC. PC can be used to turn the Safety Lock function on or off on a product. This control is only available on a product whose Video Wall is enabled.
Page 38 Video Wall On Video Wall User Control • Function • Function Turn Video Wall on or off on the product from your computer. Turn the Video Wall function on or off on the product from your computer. • Get Video Wall On/Off Status •...
Page 39 5x5 Video Wall Model 10x10 Video Wall Model 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x15 0x11 0x12 0x13 0x14 0x1F 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19...
Page 40 5x5 Video Wall Model : ( 1 ~ 25 ) • Ack Set Number Data Header Command Data length Ack/Nak r-CMD Val1 Val2 Checksum 0x01 0xAA 0xFF 0x89 Wall_Div Wall_SNo 0x02 • Nak Header Command Data length Ack/Nak r-CMD Val1 Checksum 0x18 0xAA...
Page 41: Connecting And Using A Source Device
Chapter 03 Connecting and Using a Source Device Before Connecting Check the following before you connect this product with other devices. Devices that can be connected to this product Pre-connection Checkpoints include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players. ―...
Page 42: Connecting To A Pc
Connecting to a PC • Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. • A PC can be connected to the product in a variety of ways. Select a connection method suitable for your PC.
Page 43: Connection Using An Hdmi-Dvi Cable
Connection Using an HDMI-DVI Cable Connection Using an DP Cable ― When you connect a PC to the product using an HDMI-DVI cable, set Edit Name DVI PC access video and audio content stored on the PC. DP OUT DVI OUT DP IN HDMI IN 1, HDMI IN 2 AUDIO OUT...
Page 44: Changing The Resolution
Changing the Resolution ― Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. ― The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel Display Settings, and change the resolution.
Page 45: Changing The Resolution On Windows 7
Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution, and change the resolution. Changing the Resolution on Windows 8 Go to Settings Control Panel Display Screen Resolution, and change the resolution.
Page 46: Connecting To A Video Device
Connecting to a Video Device • Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. • You can connect a video device to the product using a cable. ―...
Page 47: Connection Using An Hdmi-Dvi Cable
Connection Using an HDMI-DVI Cable Connection Using an HDMI Cable ― Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. Using an HDMI cable or HDMI to DVI Cable (up to 1080p) To resolve this, additionally connect an audio cable to the audio ports on the product and video device.
Page 48: Connecting To An Audio System
Connecting to an Audio System Connecting an External Monitor ― Connecting parts may differ in different products. ― Connecting parts may differ in different products. AUDIO DP IN DP OUT AUDIO...
Page 49: Connecting The Network Box (Sold Separately)
Connecting the network box (Sold separately) ― For details on how to connect to a network box, refer to the user's manual provided with the network box upon purchase. MagicInfo To use MagicInfo, a network box (sold separately) must be connected to the product. ―...
Page 50 Enter the IP information. Select a display mode. MagicInfo Setup Wizard - v.1.12 MagicInfo Setup Wizard - v.1.12 Select TCP/IP - step 2 Select Screen Type - step 4 Obtain an IP address automatically Use the following IP address: Landscape IP address: 192 .
Page 51: Source
Changing the Input source Source allows you to select a variety of sources and change source device names. You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source. Source ―...
Page 52: Using Mdc
Chapter 04 Using MDC Configuring Settings for Multi Control DisplayPort Daisy Chain • To display the DP IN video input through the DP OUT output port, select a device connection method from Single Stream Transport (SST) and Multi Stream Transport (MST). Clone: In this Single Stream Transport (SST) output mode, the same screen output is displayed on MENU m : T...
Page 53: Mdc Program Installation/Uninstallation
MDC Program Installation/Uninstallation Installation MDC installation can be affected by the Insert the installation CD into the CD-ROM drive. graphics card, mother board and network conditions. Click the MDC Unified installation program. Select a language for installation. Next, click "OK". If a software installation window is not displayed on the main screen, install with When the...
Page 54: What Is Mdc
What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices Connecting to MDC simultaneously using a PC. Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor. Monitor 1 RS232C IN Monitor 2...
Page 55: Using Mdc Via Ethernet
Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable. Connection using a direct LAN cable ― Multiple products can be connected using the RJ45 port on the product and the LAN ports on the HUB. RJ45 MDC Computer Monitor 1...
Page 56 Connection using a cross LAN cable ― Multiple products can be connected using the RS232C IN / OUT port on the product. Monitor 1 RJ45 MDC RS232C OUT Monitor 2 Computer...
Page 57: Connection Management
Connection Management Connection management includes the Connection list and Connection list modification options. Connection list - Connection list shows the details of the connections such as connection setting (IP/COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion.
Page 58: User Login
User Login Launching the program displays the user login window. The initial login ID (Username: admin) and password (password: admin) are set to admin. ― After logging in for the first time, make sure to change the password to ensure security. ―...
Page 59: Auto Set Id
Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0. ―...
Page 60: Cloning
Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window. ― To delete the settings you have configured, click the Paste Settings button.
Page 61: Command Retry
Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10.
Page 62: Getting Started With Mdc
Getting Started with MDC To start the program, click Start Programs Samsung MDC Unified. The login window appears after the MDC program is launched. Enter the user ID and password. • The default user ID and password are admin. • Make sure to change the password after the first login.
Page 63: Main Screen Layout
Main Screen Layout Change the status of a display device or the properties of the program. Menu Bar View a list of connected display devices or device groups. Device Category View a list of schedules for display devices. Schedule Category Select the display device you want to adjust.
Page 64 ― The volume can be changed or the sound can be muted only for displays that are turned on. Volume Volume • Adjust the volume of a selected display. • The volume can be adjusted using the slider bar in the range of 0 to 100. Mute •...
Page 65: Screen Adjustment
User Login User Settings • Add, delete or edit login information. Logout • Log out from the current user account as follows. • Click Logout. The message "Do you want to log admin out?" is displayed • Click Yes. The user login window appears. •...
Page 66 Color Color • Adjust the colors for the selected display device. Tint (G/R) • Adjust the tint for the selected display device. Color Tone • Adjust the background color tone for the selected display device. Color Temp. • Adjust the color temperature for the selected display device. ―...
Page 67 MPEG Noise Filter Reduces MPEG noise to provide improved picture quality. Medium High Auto • Smart LED Controls the LED backlight to maximize picture clarity. Cinema Black In Movie mode, this feature dims the top and bottom areas of the video image to provide a more immersive viewing experience.
Page 68: Advanced Features
Advanced features 3D Mode Select the 3D input format. 3D L/R Change Swap the left and right pictures. Displays the image for the left eye only. 3D Auto View 3D Control 3D Auto View Message Notice, a pop up message window appears when the product receives a 3D signal. If you set 3D Optimization The overall adjustment of 3D effect.
Page 69 Advanced Settings Dynamic Contrast Adjust the screen contrast. Gamma Control Adjust the primary color intensity. RGB Only Mode Displays the Red, Green Blue color for making fine adjustments to the hue and saturation. Flesh Tone Emphasize pink “Flesh Tone. ” Motion Lighting Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
Page 70: Sound Adjustment
Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. Bass • Adjust the bass for the selected display. Treble • Adjust the treble for the selected display. Balance(L/R) Bass Treble - The...
Page 71 Format • Select the number of horizontal display devices. • Select the format to display the split screen. • A maximum of 15 displays can be arranged in a row. ― A maximum of 6 can be assigned to if 15 is assigned to H. •...
Page 72 General User Auto Color • Automatically adjust the screen colors. ― Available only in mode. Auto Power • Set the product to automatically power on. Standby Control • Set the standby mode to activate if an input source is not detected. Fan &...
Page 73: Osd Display
Security Safety Lock • Lock the on-screen menus. ― To unlock the menus, set Safety Lock to Off. Button Lock • Lock the buttons on the display device. ― To unlock the buttons, set Button Lock to Off. OSD Display Source OSD •...
Page 74 Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer On Timer • Repeat: Specify the period for which you want to repeat the selected Timer. Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, Manual Holiday...
Page 75: Holiday Management
Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a specified date. ― The Holiday Management function can be enabled or disabled in the Timer settings menu. •...
Page 76 Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time. Timer: You can set the timer for Screen Saver. • • Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals (Period).
Page 77 Safety Screen Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time.
Page 78 Ticker Input text while a video or image is displayed and display the text on the screen. Ticker Enable or disable Ticker. • Message Enter a message to display on the screen. Timer Start Time End Time Set the to display a message (Message). Position Horizontal and Vertical.
Page 79: Tool Settings
Tool Settings Panel Control: Turn on or off the screen of a display device. • Remote Control: Enable or disable the remote control. • Security Reset Reset Picture: Reset the screen settings. • Reset Sound: Reset the sound settings. • Reset System: Reset the system settings.
Page 80: Edit Column
Edit Column Configure the settings for the items that will be displayed on the list of displays. • Language: Select a language to use in the MDC program. After selecting a language, restart the MDC program to use the selected language. Options Command Retry Count: Specify the number of retry attempts when a command fails.
Page 81 Monitor Window A window appears showing details for data transfer between the computer and display devices. Filter • Information View the program information.
Page 82: Other Functions
Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window.
Page 83: Group Management
Group Management Create groups and manage the list of sets on a group basis. ― Duplicate group names cannot be used. Group Edit Creating Groups Right-click and select in the display device list section on the left side of the program window. In the Edit Group window displayed, click...
Page 84 Add on the sub level: Create a sub-group under the selected group. • Enter the group name. Deleting Groups Select a group name, and click Edit. In the Edit Group window displayed, click Delete. Click Yes. The group will be deleted.
Page 85: Schedule Management
Renaming Groups Select a group name, and click Edit. Edit Group window displayed, click Rename. In the If a cursor appears in the old group name, enter a new group name. Rename Schedule Management Creating Schedules Create and register a schedule on a group basis. Click All Schedule List in the schedule section on the left side of the program window.
Page 86 Click the button. The Add Schedule window will appear. Device Group Click below the item, and select the group you want to add a schedule to. Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list Select window.
Page 87: Troubleshooting Guide
Troubleshooting Guide - This program may malfunction sometimes due to a communication Issue Solution problem between the PC and display or electromagnetic waves emitted from The display you want to control does not Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). nearby electronic devices.
Page 88 How display properties are shown when multiple displays are used When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 and ID 3): The settings for ID 1 are displayed before the settings for ID 3. When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.
Page 89: Screen Adjustment
Chapter 05 Screen Adjustment Picture Color Tone, etc.). Configure the settings (Backlight, Picture - The layout of the menu options may vary depending on the product. Picture Mode If the input source is PC, DVI or DisplayPort • Information: This mode reduces eye fatigue and is suitable for displaying information to the public. MENU m : T Picture...
Page 90: Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R)
Backlight / Contrast / Brightness / Your product has several options for adjusting picture quality. Input source Picture Mode Adjustable options Sharpness / Color / Tint (G/R) PC, DVI, DisplayPort, HDMI1 Information Backlight Contrast Brightness (when a PC is connected), HDMI2 (when a Sharpness...
Page 91: Screen Adjustment
Screen Adjustment Picture Size choose size and aspect ratio picture displayed on screen. ― Different MENU Picture Screen Adjustment ENTER m : T Screen Adjustment options are displayed depending on the current input source. • 16:9: Sets the picture to 16:9 wide mode.
Page 92: Picture Sizes Available By Input Source
Picture Sizes available by Input Source. Input Source Picture Size Component 16:9, Zoom1, Zoom2, 4:3, Custom (480i, 480p) Component (1080i, 1080p) 16:9, 4:3, Wide Fit, Screen Fit, Custom HDMI1, HDMI2 (720p, 1080i, 1080p) 16:9, 4:3, Smart View Smart View 2, Custom, Wide Fit, Screen Fit...
Page 93: Position
Position Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Wide Fit, Screen Fit or Custom. ― To use the Position function after selecting Zoom1, Zoom2, Wide Fit Screen Fit, follow these steps. Press the button to select Position.
Page 94: Pc Screen Adjustment
PC Screen Adjustment Coarse Fine • Removes or reduces picture noise. If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible (Coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the center Screen Adjustment of screen.
Page 95: Auto Adjustment
Auto Adjustment Adjust frequency values/positions and fine tune the settings automatically. MENU m : T Picture Auto Adjustment ENTER Picture Auto Adjustment - Available in mode only. - The displayed image may differ depending on the model. Rotation Rotate the product screen orientation. •...
Page 96: Aspect Ratio
Aspect Ratio Set the rotated screen to be either full screen or original. Full Screen: Display the rotated screen in full screen. • • Original: Display the rotated screen in the original aspect ratio. MENU Picture Aspect Ratio ENTER m : T ―...
Page 97: Advanced Settings
Advanced Settings Input Source Picture Mode Advanced Settings PC, DVI, DisplayPort, HDMI1 Information, Calibration White Balance Gamma (when a PC is connected), MENU m : T Picture Advanced Settings ENTER HDMI2 (when a PC is Advertisement Dynamic Contrast Black Tone Flesh Tone Color Space connected)
Page 98: Dynamic Contrast
Dynamic Contrast Advanced Settings Adjust the screen contrast. Dynamic Contrast Medium Medium High • Black Tone Black Tone Flesh Tone Select the black level to adjust the screen depth. RGB Only Mode Dark Darker Darkest • Color Space Native Flesh Tone White Balance Emphasize pink Flesh...
Page 99: White Balance
White Balance Advanced Settings Adjust the color temperature for a more natural picture. R-Offset G-Offset / B-Offset: Adjust each color’s (red, green, blue) darkness. • White Balance R-Gain G-Gain / B-Gain: Adjust each color’s (red, green, blue) brightness. • 10p White Balance •...
Page 100: Expert Pattern
Expert Pattern Advanced Settings Use the Expert Pattern function to calibrate the picture. If the OSD menu disappears or a menu other than the Picture menu is opened, the product saves the calibration and the White Balance Expert Pattern screen disappears. •...
Page 101: Picture Options
Picture Options Select an option using the and arrow keys, the press Use the arrow keys to change the setting, and then press Input source Picture Mode Picture Options m : T MENU Picture Picture Options ENTER Information Color Tone Calibrated Value Dynamic Backlight Picture Options...
Page 102: Color Tone
Color Tone Picture Options If the input source is PC, DisplayPort HDMI1 (PC connection), HDMI2 (PC connection). Standard Color Tone Cool Standard Warm • If the input source is AV, Component, HDMI1, HDMI2 or DVI. 10000K Color Temp. Cool Standard Warm1 Warm2 •...
Page 103: Film Mode
Film Mode Picture Options This mode is suitable to view movies. Film Mode Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality. Auto1 Auto2 • Calibrated Value Don't Apply ―...
Page 104: Network
The Modem Port on the Wall External Modem connected. (ADSL / VDSL) Start Please plug in a network cable or a Samsung Wireless LAN Adapter. Cancel Modem Cable LAN Cable • You can attach your product to your LAN by connecting the LAN port on the back of your product to an IP Sharer which is connected to an external modem.
Page 105: Wired Network Settings
Wired Network Settings • Depending on how your network is configured, you may be able to attach your product to your LAN by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN cable. Set the network connection to use Internet services such as perform software upgrades.
Page 106: Connecting To A Wireless Network
PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode. ― If your router, modem, or device is not certified, it may not connect to the product via the “Samsung Wireless LAN adapter”.
Page 107: Wireless Network Setting
― The product may not recognize the “Samsung Wireless LAN adapter” if you connect it to the product When the connection has been verified, the “Your wireless network and Internet connection with a USB hub or USB extension cable other than the cable supplied with the product.
Page 108: Wps(Pbc)
WPS(PBC) If the router has security, enter the Security key (Security key or PIN). When done, use the right arrow button to move the cursor to Next, and then press . The How to set up using WPS(PBC) network connection screen appears and the verification process starts. If your router has a WPS(PBC) button, follow these steps.
Page 109: Network Status
Network Status Wi-Fi Direct MENU Network Network Status ENTER MENU Network Wi-Fi Direct ENTER m : T m : T You can check the current network and Internet status. Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
Page 110: Soft Ap
Soft AP AllShare Settings MENU Network Soft AP ENTER MENU Network AllShare Settings ENTER m : T m : T Using this function, you can connect the product on your mobile devices if your mobile devices do not Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play support Wi-Fi...
Page 111: System
Chapter 07 System Multi Control Configuring settings for Multi Control ID Setup • Assign an ID to a set. (Range: 0~99) MENU m : T System Multi Control ENTER Press to select a number, and press Multi Control ID Input •...
Page 112: Time
Time You can configure Clock Set Sleep Timer. You can also set the product to automatically turn on or off at a specified time using the Timer function. Clock Set MENU System Time ENTER m : T Set the clock to use the various various timer features of the product. Time Clock Set •...
Page 113: On Timer
On Timer Time On Timer so that your product turns on automatically at a time and on a day of your choosing. On Timer The power is turned on with the specified volume or input source. Off Timer Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time first. (On Timer1 Timer7) Holiday Management...
Page 114: Off Timer
Off Timer Time Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer1 Timer7) On Timer ― You must set the clock before you can use Timer. Off Timer • Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual.
Page 115: Menu Language
Menu Language Set the menu language. ― A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC. m : T MENU System Menu Language ENTER System Time...
Page 116: Eco Solution
Eco Solution Energy Saving Reduce the power consumption by adjusting the screen brightness. m : T MENU System Eco Solution ENTER Selecting Picture Off switches off the screen. The volume is not disabled. To switch the screen on, press any button other than the volume button. Eco Solution Medium High...
Page 117: Caption
Caption Caption You can switch the caption function on or off. m : T MENU System Caption ENTER If captions are not available, they will not be displayed on the screen. • Caption ― The Caption feature does not work with devices connected to the product through the Component, HDMI1, HDMI2 input jacks.
Page 118: Security
Security Every time you access the Security functions, the PIN screen will appear and the default PIN number is "0-0-0-0" (default password: 0 - 0 - 0 - 0). Safety Lock m : T MENU System Security ENTER It sets safe lock function. Security •...
Page 119: Pip
PIP Settings The picture from the external video source will be in the main screen and the picture from the product will be in the PIP sub- picture screen. m : T MENU System ENTER Main picture Sub picture System PC, DVI, HDMI1, HDMI2, DisplayPort Auto Protection Time...
Page 120: Auto Protection Time
Auto Protection Time If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen. 2 hours 4 hours 8 hours 10 hours •...
Page 121: Screen Burn Protection
Screen Burn Protection To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology. Pixel Shift moves the picture slightly on the screen. Pixel Shift Time setting allows you to program the time between movements of the picture in minutes. m : T MENU System...
Page 122: Timer
Timer Screen Burn Protection You can set the timer for Screen Burn Protection. Pixel Shift Pixel Shift feature stops automatically after a specified period of time. Timer Timer Immediate Display • Side Gray • Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
Page 123: Immediate Display
Immediate Display Screen Burn Protection Select the screen saver you want to display immediately. Pixel Shift Pixel Rolling Bar Fading Screen • Timer Side Gray Immediate Display When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen. Side Gray Light Dark...
Page 124: Video Wall
Video Wall Customize the layout of multiple displays that are connected to form a video wall. In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays. To display multiple images, refer to MDC Help or the MagicInfo user guide.
Page 125: Vertical
Vertical Video Wall This function automatically divides the screen according to the specified number of vertical displays. Video Wall Enter the number of vertically arranged displays. Format Full · The vertical screen will automatically be divided according to the number entered. A maximum of 15 displays can be assigned to the vertical arrangement.
Page 126: Source Autoswitch Settings
Source AutoSwitch Settings Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video. Source AutoSwitch m : T MENU System Source AutoSwitch Settings ENTER When the...
Page 127: General
Auto BD Wise Wise. When Provides the optimal picture quality for Samsung DVD, Blu-ray and Home Theater products which support Wise is turned On, the picture mode is automatically changed to the optimal resolution. - The displayed image may differ depending on the model.
Page 128: Sound Feedback
Sound Feedback General Your product gives sound feedback when you use product. Sound Feedback Sound Feedback is enabled by default. Turn off Sound Feedback or adjust its volume. Auto Power This function is enabled by default. The volume can be adjusted or muted. ―...
Page 129: Lamp Schedule
Lamp Schedule General Enables the lamp value to be adjusted to a user-specified value at a specified time in MDC mode. Sound Feedback • Auto Power OSD Display Standby Control Auto Lamp Schedule Displays or hides a menu item on the screen. ―...
Page 130: Anynet+ (Hdmi-Cec)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your...
Page 131: Auto Turn Off
Auto Turn Off Anynet+ (HDMI-CEC) Anynet+ Setting an Device to turn automatically when the product is turned off. Anynet+ (HDMI-CEC) • Auto Turn Off ― If Auto Turn Off is set to Yes, running external devices will turn off at the same time as the product powers off. ―...
Page 132: Troubleshooting For Anynet
Troubleshooting for Anynet+ Problem Possible Solution Anynet+ does not work. • Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only. • Check if the Anynet+ device power cord is properly connected. • Check the Anynet+ device’s Video/Audio/HDMI cable connections. •...
Page 133 Problem Possible Solution The connected device is not • Check whether or not the device supports Anynet+ functions. displayed. • Check whether or not the HDMI cable is properly connected. Anynet+ (HDMI-CEC) Anynet+ (HDMI-CEC) Setup • Check whether is set to in the menu.
Page 134: Divx® Video On Demand
DivX® Video On Demand Shows the registration code authorized for the product. If you connect to the DivXⓇ web site and register using that code, you can download the VOD registration file. For more information about DivXⓇ VOD, visit “http://vod.divx.com”. m : T MENU System...
Page 135: Magic Clone
Magic Clone Export the product settings to a USB device or load the settings via a USB device. This option is useful when assigning the same settings to several products. Clone to USB: Copy the product settings to a USB device. •...
Page 136: Reset All
Reset All This option returns all the current settings for a display to the default factory settings. m : T MENU System Reset All ENTER System Reset All - The displayed image may differ depending on the model. PC Module Power The PC module can be turned on/off separately from the LFD.
Page 137: Support
Chapter 08 Support Software Update m : T MENU Support Software Update ENTER Software Update menu lets you upgrade your product software to the latest version. Current Version: This is the software ― Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade. version already installed in the product.
Page 138: Alternative Software
The product displays a message asking if you want to upgrade. Select Address. The product begins the upgrade. When the upgrade is complete, the product turns off automatically, and then turns on. Contact Samsung m : T MENU Support...
Page 139: Contents Home
Contents Home MagicInfo Lite m : T MENU Support Contents Home MagicInfo Lite ENTER ― m : T MENU Support Contents Home ENTER MagicInfo Lite can also be accessed by pressing MagicInfo Lite/S on the remote control. ― To launch MagicInfo Lite, select MagicInfo Lite...
Page 140: Allshare Play
AllShare Play MENU m : T Support Contents Home ENTER AllShare Play Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device. ― Refer to P.141 for details about the AllShare Play menu. Source MENU m : T Support Contents Home Source...
Page 141: Allshare Play
• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost. Samsung Electronics is not liable for any damage or loss of data. • Do not remove a USB device while it is loading.
Page 142 Compatible devices with AllShare Play • Some types of USB devices, digital cameras and audio devices may not be compatible with the product. AllShare Play is only compatible with USB MSC devices. • • MSC device refers to a Mass Storage Class Bulk-Only Transport device. Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs.
Page 143: Using A Usb Device
Using a USB device Connecting a USB device Turn on your product. It is recommended to use a USB HDD that has a power adapter. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. A message New device connected.
Page 144: Connecting To A Pc Over A Network
Settings. • To view content saved on the PC, connect the product and PC to the same wireless router and visit http://www.samsung.com to download the AllShare PC software. • Ensure the product and PC are connected to the same network subnet.
Page 145: Using The Allshare Play Features
• Compatibility with various subtitle formats (SRT, SMI, SUB, TXT, TTXT) • Search with file names • And many others ― A compatibility issue may occur if a video file is played when a server not provided by Samsung Electronics is connected. ― To use AllShare...
Page 146: Using The Basic Allshare Play Features
Using the Basic AllShare Play Sorting the file lists Features To sort files, press on the remote control to specify the sorting criteria. Sort Criteria Operation Videos Photos Music MENUm → Support → Contents Home → AllShare Play → ENTERE Folder view Displays the whole folder.
Page 147: Playing Selected Files
Playing Selected Files Creating a Playlist Select files from the list of Videos, Photos, or Music Select files from the list of Videos, Photos, or Music files. files. Press TOOLS on the remote control and select Selection Play. Press TOOLS on the remote control and select Add to Playlist.
Page 148: My List
My List MENUm → Support → Contents Home → AllShare Play → My List → ENTERE Access desired content more conveniently and quickly. Playlist To play files, select files or a and press E. Recently Played: Display video, photo or music files that were recently played. This mode is suitable when playing files again that were played before. •...
Page 149: Videos
Videos MENUm → Support → Contents Home → AllShare Play → Videos → ENTERE Playing a Video Select the internal memory or a USB device. Select files from the list of files. Press the E button or ∂ (Play) button. •...
Page 150: Photos
Photos MENUm → → → → → ENTERE Support Contents Home AllShare Play Photos Viewing a Photo (or Slide Show) Select the internal memory or a USB device. Select a file from the list of files. Press the E button. •...
Page 151: Music
Music MENUm → → → → → ENTERE Support Contents Home AllShare Play Music Playing Music Select the internal memory or a USB device. Select files from the list of files. Press the E button or ∂(Play) button. • When the music is playing, you can search using the π(REW) and µ(FF) button. ―...
Page 152: Videos / Photos / Music Play Option Menu
Videos / Photos / Music Play Option menu When playing video or photo files, you can press the TOOLS button to display an Options menu. - Pressing the INFO button while a device name is selected will display Option Name Operations Videos Photos...
Page 153 Option Name Operations Videos Photos Music Sound Mode You can change the Sound Mode. Audio Language You can enjoy video in one of supported languages. The function is enabled only when you play stream-type files which support multiple audio formats. Subtitle You can view a subtitle.
Page 154: Supported Subtitle And Allshare Play File Formats
Supported Subtitle and AllShare Play file formats Subtitle External Internal • MPEG-4 timed text (.ttxt) • Xsub Container: AVI • SAMI (.smi) • SubStation Alpha • SubRip (.srt) Container: MKV • SubViewer (.sub) • Advanced SubStation Alpha • Micro DVD (.sub or .txt) Container: MKV •...
Page 155: Supported Music File Formats
Supported music file formats File Extension Type Codec Comments *.mp3 MPEG MPEG1 Audio Layer 3 *.m4a, *.mpa, *.aac, *.3ga MPEG4 *.flac FLAC FLAC The Seek (jump) function is not supported. Supports up to 2 channel Supported Video Formats • Video content will not play, or not play correctly, if there is an error in the content or the container. •...
Page 156 File Container Video Codec Resolution Frame rate Bit rate Audio Codec Extension (fps) (Mbps) *.avi DIVX 3.11 / 4.x / 5.x / 6.x 1920 x 1080 6~30 *.mkv LPCM *.asf ADMPCM MPEG4 SP / ASP *.wmv (IMA, MS) *.mp4 *.mov HE-AAC H.264 BP / MP / HP *.3gp...
Page 157: Magicinfo Lite
Chapter 10 MagicInfo Lite File Formats Compatible with MagicInfo Lite Player MagicInfo Lite, select - To launch MagicInfo Lite for the Player Mode the System. Read before using MagicInfo Lite Player • The file system supports FAT16, FAT32 and NTFS. •...
Page 158 Contents File Extension Container Video Codec Resolution Frame rate Bit rate Audio Codec (fps) (Mbps) *.avi DIVX 3.11 / 4.x / 5.x / 6.x 1920 x 1080 6~30 *.mkv LPCM *.asf MPEG4 SP / ASP *.wmv HE-AAC *.mp4 *.mov H.264 BP / MP / HP *.3gp MPEG(MP3) *.vro...
Page 159 Video Audio Image • 3D video is not supported. • Audio content with a Bit rate or Frame rate • Compatible image file format : Jpeg larger than the rate specified in the table above • Content with a resolution larger than the •...
Page 160 Flash Power Point • Compatible with Flash 10.1 • Compatible document file formats • Flash Animation - Extension : ppt, pptx - Version : Office 97 ~ Office 2007 - Compatible file format : SWF • Functions not supported • Recommended resolution : 960 x 540 - Caution - Animation effect - 3D shapes (which will be displayed in 2D)
Page 161 WORD • Compatible document file formats • Compatible document file formats - Extension : pdf - Extension : .doc, .docx - Version : Office 97 ~ Office 2007 • Functions not supported - Content less than 1 pixel not supported because of performance •...
Page 162: Approving A Connected Device From The Server
Approving a connected device from the Select Lite from the menus on the left. server Unapproved from the sub-menus of Lite. Select Access the server you have assigned to your device. Select the Approve button for your device from the list of unapproved Lite devices. Enter your ID and password to log in.
Page 163: Setting The Current Time
Enter the information required to approve the device. When the device is approved by the server, the schedule registered in the selected group will be downloaded to the device. The schedule will run after it is downloaded. ― For further details on how to configure a schedule, refer to the <MagicInfo Lite Server user's manual>. ―...
Page 164: Magicinfo Lite
MagicInfo Lite Select Network Schedule in the MagicInfo Lite Player menu. MagicInfo Lite Player MENUm → Support → Contents Home → MagicInfo Lite → ENTERE ― To launch Network Schedule MagicInfo Lite, select MagicInfo Lite for the Player Mode on the System. Local Schedule ―...
Page 165: Local Schedule
Local Schedule → Click to create a schedule → Select the schedule you want to run Go to Local Schedule Manager Create Local Schedule MagicInfo Lite Player Select in the menu screen. MagicInfo Lite Player Run schedules created in Local Schedule Manager.
Page 166: Usb Autoplay
― The option is enabled only when there is at least one content item, except for music files, in the "MagicInfoSlide" folder on USB AutoPlay USB Storage. ― Ensure a USB device is inserted. Be sure to create a folder named "MagicInfoSlide" in the USB device and put content in the MagicInfo Lite Player folder.
Page 167: Local Schedule Manager
Local Schedule Manager Create Local Schedule Manager Select in the screen. Configure the settings for playback from Local Schedule. Local Schedule Manager Alternatively, select and play content from internal or USB memory according to the customized playback Create sequence. Storage Internal Memory Edit No Playing Schedule...
Page 168 Contents Duration Select to specify the content you want to play. Select Contents Direction Internal Memory Contents Duration No Item Folder1 Menu1.jpg 00:00:05 Menu1.jpg Menu2.jpg 00:00:05 Menu2.jpg Deselect All Down Save Cancel Duration Cancel Return Return Specify the sequence and time duration to play content files. - A maximum of 99 content files can be selected.
Page 169: Modifying A Local Schedule
Select Save. Select the memory space you want to save the content to. Modifying a Local Schedule ― Ensure at least one Local Schedule is registered. Create Select Local Schedule Manager in the MagicInfo Lite menu screen. Time --:-- am~ --:-- pm Delete Contents Menu1.jpg Menu2...
Page 170: Deleting A Local Schedule
Deleting a Local Schedule Select Edit. ― Ensure at least one Local Schedule is registered. Edit Select Local Schedule Manager in the MagicInfo Lite menu screen. Time 12:00 am~ 12:00 pm Delete Menu1.jpg Menu2 Contents MagicInfo Lite Save --:-- am~ --:-- pm Time MagicInfo Lite Player Contents...
Page 171: Running A Local Schedule
Running a Local Schedule Stopping a Local Schedule ― Ensure at least one ― This function is enabled only when a schedule is running. Local Schedule is registered. Selecting Stop will change the running mode from Local Schedule Network Schedule. Select Local Schedule Manager in the...
Page 172 Viewing the details of a Local Schedule The details of the schedule will be displayed. Select Local Schedule Manager in the MagicInfo Lite menu screen. Information 2012.01.01_1834.lsch MagicInfo Lite 12:00 am~12:00 pm, 2 File(s) - Menu1.jpg Menu2.jpg MagicInfo Lite Player Local Schedule Manager Close Content Manager...
Page 173 Copying a Local Schedule Select local schedule files and press Copy. Select Local Schedule Manager in the MagicInfo Lite menu screen. Local Schedule Manager Storage Internal Memory Create MagicInfo Lite Edit No Playing Schedule MagicInfo Lite Player Delete All Schedules Local Schedule Manager 2012.01.01_1834.lsch Content Manager...
Page 174: Content Manager
Content Manager Select the content you want to copy. Content Manager Copying content Internal Memory Select Content Manager in the MagicInfo Lite menu screen. Folder1 No Item Menu1.jpg Menu2.jpg MagicInfo Lite Player MagicInfo Lite Player Copy Local Schedule Manager Delete Free Space Free Space 5549.2MB...
Page 175: Deleting Content
Deleting content Select the content you want to delete. Next, select Delete. Internal Memory • Content under memory can be deleted at the same time. Select Content Manager in the MagicInfo Lite menu screen. Content Manager MagicInfo Lite Player Internal Memory MagicInfo Lite Player Menu3.jpg Folder1...
Page 176: Settings
Settings Server Network Settings MagicInfo Lite, connect to a network. To run Settings Server Server Network Settings Enter the MagicInfo Lite server settings. Content Default Duration (E.g.: http://192.168.0.10:7001/MagicInfo/) Content Ratio Close • If the option is enabled, the server is configured to use https and data transfer is encrypted. Image Effect Random ―...
Page 177: Screen Layout
Content Default Duration Screen Layout Specify the duration to play content. Change the screen orientation to landscape or portrait view. Image Viewer Time, PPT Viewer Time, PDF Viewer Time, Flash Viewer Time Landscape Portrait • • ― The duration must be at least 5 seconds. Schedule Name Content Ratio Select a schedule title format when creating a local schedule.
Page 178: When Content Is Running
When Content is Running Press the INFO button on the remote control. Software Version: Displays the software version of a device • Device Name: Displays the name of a device recognized by the server • Viewing the details of the content that is running Device ID: Displays the original identification number of a device •...
Page 179 Changing the settings for the content that is running Press the TOOLS button on the remote control. You can change the Picture Mode Sound Mode setting or safely remove a USB device (Safely Remove USB) while content Tools is playing by pressing the TOOLS button on the remote control. Picture Mode (Dynamic Standard Natural...
Page 180: Magicinfo Premium S
MagicInfo Premium S A license needs to be purchased to use MagicInfo Premium MagicInfo Premium S, select - To launch To download the software, go to the Samsung homepage at http://www.samsunglfd.com. MagicInfo Premium S for the Player Mode on the System.
Page 181 Video Audio Image • 3D video is not supported. • Audio content with a Bit rate or Frame rate • Compatible image file format : Jpeg larger than the rate specified in the table above • Content with a resolution larger than the •...
Page 182 Flash Power Point • Compatible with Flash 10.1 • Compatible document file formats • Compatible document file formats - Extension : ppt, pptx - Extension : pdf • Flash Animation - Compatible file format : SWF - Version : Office 97 ~ Office 2007 •...
Page 183 WORD Template files • Compatible document file formats • Creation/editing/playback are only available in • Supported in USB AutoPlay Network Template Manager. - Extension : .doc, .docx Schedule (Authored in a PC authoring tool for - Version : Office 97 ~ Office 2007 Premium S Player) •...
Page 184: Network Schedule Multiframe
Network Schedule Multiframe Playback restrictions • A maximum of two video (Videos) files can be played. • If mode is enabled, more than one video (Videos) file cannot be played. • More than one Flash file cannot be played. • For Office files (PPT and Word files) and files, only one file type is supported at a time.
Page 185 Playback restrictions • A maximum of two video (Videos) files can be played. • If mode is enabled, more than one video (Videos) file cannot be played. • More than one Flash file cannot be played. • For Office files (PPT and Word files) and files, only one file type is supported at a time.
Page 186: Approving A Connected Device From The Server
Approving a connected device from the Select Premium from the menus on the left. server Unapproved from the sub-menus of Premium. Select Access the server you have assigned to your device. Select the Approve button for your device from the list of unapproved Premium devices. Enter your ID and password to log in.
Page 187 Enter the information required to approve the device. When the device is approved by the server, the schedule registered in the selected group will be downloaded to the device. The schedule will run after it is downloaded. ― For further details on how to configure a schedule, refer to the <MagicInfo Premium Server user's manual>.
Page 188: Magicinfo Premium S
MagicInfo Premium S Select Network Schedule in the MagicInfo Premium S Player menu. MagicInfo Premium S Player MENU m : T Support Contents Home MagicInfo Premium S ENTER E ― To launch Network Schedule MagicInfo Premium S, select MagicInfo Premium S for the Player Mode on the...
Page 189 Local Schedule → Click to create a schedule → Select the schedule you want to run Go to Local Schedule Manager Create Local Schedule MagicInfo Premium S Player Select in the menu screen. MagicInfo Premium S Player Run schedules created in Local Schedule Manager.
Page 190 ― The option is enabled only when there is at least one content item, except for music files, in Internal AutoPlay Internal Memory. Select Internal AutoPlay in the MagicInfo Premium S Player menu screen. MagicInfo Premium S Player • Play content, which has been copied to Internal Memory, in alphabetical order.
Page 191: Local Schedule Manager
Local Schedule Manager Select Create in the Local Schedule Manager screen. Local Schedule. Configure the settings for playback from Local Schedule Manager Alternatively, select and play content from internal or USB memory according to the customized playback Create sequence. Storage Internal Memory Edit No Playing Schedule...
Page 192 Select Contents to specify the content you want to play. Select Duration Contents Direction Internal Memory Contents Duration No Item Folder1 Menu1.jpg 00:00:05 Menu1.jpg Menu2.jpg 00:00:05 Menu2.jpg Down Deselect All Save Cancel Duration Cancel Return Return Specify the sequence and time duration to play content files. - A maximum of 99 content files can be selected.
Page 193 Select Save. Select the memory space you want to save the content to. Modifying a Local Schedule ― Ensure at least one Local Schedule is registered. Create Select Local Schedule Manager in the MagicInfo Premium S menu screen. Time --:-- am~ --:-- pm Delete Contents Menu1.jpg Menu2...
Page 194 Select Edit. Deleting a Local Schedule ― Ensure at least one Local Schedule is registered. Edit Select Local Schedule Manager in the MagicInfo Premium S menu screen. Time 12:00 am~ 12:00 pm Delete Menu1.jpg Menu2 Contents MagicInfo Premium S Save Time --:-- am~ --:-- pm MagicInfo Premium S Player...
Page 195 Running a Local Schedule Stopping a Local Schedule ― Ensure at least one ― This function is enabled only when a schedule is running. Local Schedule is registered. Selecting Stop will change the running mode from Local Schedule Network Schedule. Select Local Schedule Manager in the...
Page 196 Viewing the details of a Local Schedule The details of the schedule will be displayed. Local Schedule Manager MagicInfo Premium S Select in the menu screen. Information 2012.01.01_1834.lsch MagicInfo Premium S 12:00 am~12:00 pm, 2 File(s) - Menu1.jpg Menu2.jpg MagicInfo Premium S Player Local Schedule Manager Close Template Player...
Page 197 Copying a Local Schedule Select local schedule files and press Copy. Local Schedule Manager MagicInfo Premium S Select in the menu screen. Local Schedule Manager Storage Internal Memory Create MagicInfo Premium S Edit No Playing Schedule Delete MagicInfo Premium S Player All Schedules Local Schedule Manager 2012.01.01_1834.lsch...
Page 198: Template Manager
Template Manager Select Create in the Template Manager screen. Template Manager Registering a Template Create Storage Internal Memory Select Template Manager in the MagicInfo Premium S menu screen. Edit No Playing Schedule Copy MagicInfo Premium S Delete Play MagicInfo Premium S Player Preview Local Schedule Manager Close...
Page 199 Contents Organize a template by inserting text, video, photo, or PDF files as desired. Contents Create Type None Select the position and background. Contents No Item Use background image Size Fit to screen Preview Source Previous Cancel Next Return Cancel •...
Page 200 Select Sound/Background music. Select Save. Select the memory space you want to save the content to. Create Create Select Sound/Background music. Save the template and finish. Storage Internal Background Music Template Name 20130101_2222 Preview Preview Previous Previous Next Cancel Cancel Videos •...
Page 201: Content Manager
Content Manager Select the content you want to copy. Content Manager Copying content Internal Memory Select Content Manager in the MagicInfo Premium S menu screen. Folder1 No Item Menu1.jpg Menu2.jpg MagicInfo Premium S MagicInfo Premium S Player Copy Local Schedule Manager Delete Free Space Free Space...
Page 202 Deleting content Select the content you want to delete. Next, select Delete. Internal Memory • Content under memory can be deleted at the same time. Select Content Manager in the MagicInfo Premium S menu screen. Content Manager MagicInfo Premium S Internal Memory MagicInfo Premium S Player Menu3.jpg...
Page 203: Settings
Settings Server Network Settings MagicInfo Premium S, connect to a network. To run Settings Server Server Network Settings MagicInfo Premium S Enter the server settings. Content Default Duration option is enabled, the server is configured to use https and data transfer is encrypted. •...
Page 204 Content Default Duration Screen Layout Specify the duration to play content. Change the screen orientation to landscape or portrait view. Image Viewer Time, PPT Viewer Time, PDF Viewer Time, Flash Viewer Time Landscape Portrait • • ― The duration must be at least 5 seconds. Schedule Name Content Ratio Select a schedule title format when creating a local schedule.
Page 205: When Content Is Running
When Content is Running Press the INFO button on the remote control. Software Version: Displays the software version of a device • Device Name: Displays the name of a device recognized by the server • Viewing the details of the content that is running Device ID: Displays the original identification number of a device •...
Page 206 Changing the settings for the content that is running Press the TOOLS button on the remote control. Picture Mode Sound Mode (Safely Remove USB) while content You can change the setting or safely remove a USB device Tools is playing by pressing the TOOLS button on the remote control. Picture Mode (Dynamic Standard Natural...
Page 207: Magicinfo Videowall S
MagicInfo Videowall S A licence needs to be purchased to use MagicInfo Videowall MagicInfo Videowall - To launch To download the software, go to the Samsung homepage at http://www.samsunglfd.com. select MagicInfo Videowall S for the Player Mode on the System.
Page 208 Video Image • 3D video is not supported. • Compatible image file format : Jpeg, bmp, png • Content with a resolution larger than the resolution specified in the table • Supported maximum resolution : 15,360 x 8,640 above is not supported. - A higher resolution image may take longer to display on the screen.
Page 209 Restrictions • Only one video (Videos) file can be played per client. ― Different content files can be played on the displays of a video wall. Two video (Videos) files cannot be played on a single display of a video wall. Available Available Not available...
Page 210: Magicinfo Videowall S
MagicInfo Videowall S Default Storage Specify the location you want to save content (downloaded from the server) to. Internal Memory: Save the content to the internal memory of the product. • MENUm → Support → Contents Home → MagicInfo Videowall S →...
Page 211: When Content Is Running
When Content is Running Press the INFO button on the remote control. Software Version: Displays the software version of a device • Information Device Name: Displays the name of a device recognized by the server • Device ID: Displays the original identification number of a device •...
Page 212: Troubleshooting Guide
Chapter 13 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center Before calling Samsung Customer Service Testing the Product Center, test your product as follows. If the problem persists, contact Samsung Check if your product is operating normally by using the product test function.
Page 213: Check The Followings
Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product.
Page 214 Screen issue The screen is not clear. The screen is blurry. Adjust Coarse and Fine. Remove any accessories (video extension cable, etc) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product.
Page 215 Lines (red, green or blue) are displayed on the screen. These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a Samsung Service Center to resolve the issue. The display looks unstable and then freezes.
Page 216 Remote control issue The remote control does not work. Make sure that the batteries are correctly in place (+/-). Check if the batteries are flat. Check for power failure. Make sure that the power cord is connected. Check for any special lighting or neon signs switched on in the vicinity. Source device issue A beeping sound is heard when my PC is booting.
Page 217 Other issue Audio or video cuts out intermittently. Check the cable connection and connect it again if required. Using a very hard or thick cable may corrupt audio and video files. Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it is recommended to use right-angle cables.
Page 218 Other issue The IR sensor is not functioning. Make sure the sensor light turns on when a button is pressed on the remote control. • If the sensor light does not turn on, turn the power switch off and then on again on the back of the product.
Page 219: Q & A
Q & A Refer to the user manual for your PC or graphics card for further instructions on adjustment. Question Answer How can I change the frequency? Set the frequency on your graphics card. • Windows XP: Go to Control Panel Appearance and Themes Display Settings...
Page 220 Question Answer How do I set powersaving mode? • Windows XP: Set power-saving mode in Control Panel Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC. • Windows ME/2000: Set power-saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC.
Page 221: Specifications
Chapter 14 Specifications General Size Model Name UD46C UD55C Panel Size 46 Class (46.0 Inches / 116 cm) 55 Class (54.6 Inches / 138 cm) Display area (H x V) 1018.08 x 572.67 mm / 1209.6 x 680.4 mm / 40.1 x 22.6 Inches...
Page 222 ― Plug-and-Play Model Name UD46C / UD55C This monitor can be installed and used with any Plug-and- Display Color 16.7 M Play compatible systems. Two- way data exchange between the Synchronization Horizontal 30 ~ 81 kHz monitor and PC system optimizes Frequency the monitor settings.
Page 223 (USA only) Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799...
Page 224: Powersaver
UD46C 150 Watts 120 Watts 165 Watts 0.5 Watts 0.5 Watts 0 Watts UD55C 200 Watts 160 Watts 220 Watts 0.5 Watts 0.5 Watts 0 Watts ― The displayed power consumption level can vary in different operating conditions or when settings are changed.
Page 225: Preset Timing Modes
Preset Timing Modes ― This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product. Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product.
Page 226 Resolution Horizontal Frequency Vertical Frequency (Hz) Pixel Clock Sync Polarity (H/V) (kHz) (MHz) VESA, 1024 x 768 56.476 70.069 75.000 VESA, 1024 x 768 60.023 75.029 78.750 VESA, 1152 x 864 67.500 75.000 108.000 VESA, 1280 x 720 45.000 60.000 74.250 VESA, 1280 x 800 49.702...
Page 227: Contact Samsung World Wide
Chapter 15 Appendix Contact SAMSUNG WORLD WIDE ― If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca (English) http://www.samsung.com/ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com...
Page 228 LATIN AMERICA COLOMBIA 01-8000112112 http://www.samsung.com/co Bogotá: 6001272 COSTA RICA 0-800-507-7267 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) DOMINICA 1-800-751-2676 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) ECUADOR 1-800-10-7267 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) EL SALVADOR 800-6225 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) GUATEMALA 1-800-299-0013 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) HONDURAS 800-27919267 http://www.samsung.com/latin (Spanish)
Page 229 800 - SAMSUNG (800-726786) http://www.samsung.com Samsung Electronics Czech and Slovak, s.r.o., Oasis Florenc, Sokolovská 394/17, 180 00, Praha 8 till 8.2.2013 . From 8.2.2013: Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 - Praha 4 DENMARK 70 70 19 70 http://www.samsung.com...
Page 230 0180 5 SAMSUNG bzw. http://www.samsung.com 0180 5 7267864* (*0,14 €/Min. aus dem dt. Festnetz, aus dem Mobilfunk max. 0,42 €/Min.) GREECE 80111-SAMSUNG (80111 726 7864) only from land line http://www.samsung.com (+30) 210 6897691 from mobile and land line HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com...
Page 231 +381 11 321 6899 http://www.samsung.com (old number still active 0700 7267864) SLOVAKIA 0800 - SAMSUNG (0800-726 786) http://www.samsung.com SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min) http://www.samsung.com/ch (German)
Page 232 1300 362 603 http://www.samsung.com CHINA 400-810-5858 http://www.samsung.com HONG KONG (852) 3698 4698 http://www.samsung.com/hk (Chinese) http://www.samsung.com/hk_en (English) INDIA 1800 3000 8282 http://www.samsung.com/in 1800 266 8282 INDONESIA 0800-112-8888 http://www.samsung.com/id 021-5699-7777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800 SAMSUNG (0800 726 786) http://www.samsung.com...
Page 233 ASIA PACIFIC PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.com/ph 1-800-3-SAMSUNG (726-7864) for Digitel 1-800-8-SAMSUNG (726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com TAIWAN 0800-329-999 http://www.samsung.com 0266-026-066 THAILAND 1800-29-3232 http://www.samsung.com/th 02-689-3232 VIETNAM 1 800 588 889 http://www.samsung.com MIDDLE EAST BAHRAIN 8000-4726 http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic)
Page 234 MIDDLE EAST OMAN 800-SAMSUNG (726-7864) http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) QATAR 800-2255 (800-CALL) http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) SAUDI ARABIA 9200-21230 http://www.samsung.com/sa (Arabic) SYRIA 18252273 http://www.samsung.com/Levant (English) TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com AFRICA ANGOLA 91-726-7864 http://www.samsung.com BOTSWANA 0800-726-000 http://www.samsung.com...
Page 235 AFRICA SOUTH AFRICA 0860-SAMSUNG (726-7864 ) http://www.samsung.com TANZANIA 0685 88 99 00 http://www.samsung.com UGANDA 0800 300 300 http://www.samsung.com ZAMBIA 211350370 http://www.samsung.com...
Page 236: Responsibility For The Pay Service (Cost To Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service • Use of supplies or separatly sold product unspecified by Samsung. technician in the following cases. • Repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co., Ltd. Not a product defect •...
Page 237: Optimum Picture Quality And Afterimage Burn-In Prevention
Optimum Picture Quality and Afterimage Burn-in Prevention Optimum Picture Quality • To enjoy the optimum picture quality, go to Control Panel on your PC and adjust the resolution and refresh rate as follows. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. - Resolution: 1920 x 1080 - Vertical frequency (refresh rate): 48 ~ 75 Hz •...
Page 238: Prevention Of Afterimage Burn-In
Prevention of Afterimage Burn-in What is afterimage burn-in? Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an Black Matrix Color-Filter Common extended period of time (more than 12 hours), a slight voltage difference may occur between the...
Page 239 - Brightness: refers to the lightness • Avoid combinations of a text color and background color of contrasting brightness. or darkness of a color which varies ― Avoid using grey as it may contribute to afterimage burn-in. depending on the amount of light ―...
Page 240: License
License DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium content. DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of DivX, Inc. and are used under license. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol aretrademarks of Dolby Laboratories. ABOUT DIVX VIDEO: DivXⓇ...
Page 241: Terminology
Terminology 480i / 480p / 720p / 1080i / 1080p____ Each of the scanning rates above refers to the number of effective Component ports (green, blue and red)____ The component ports, which identify, transmit and receive scanning lines that decides the screen resolution. The scanning rate may be indicated in i (interlaced) or p contrast signals, provide superior picture quality to any other video connection methods.

This manual is also suitable for:

Ud46c

Samsung UD55C User Manual

Copyright

Safety Precautions

Storage

Checking the Contents

Parts

Before Installing the Product (Installation Guide)

Dimensions

Installing the Wall Mount

Remote Control (RS232C)

Before Connecting

Connecting to a PC

Changing the Resolution

Connecting to a Video Device

Connecting to an Audio System

Connecting an External Monitor

Connecting the Network Box (Sold Separately)

Configuring Settings for Multi Control

MDC Program Installation/Uninstallation

What Is MDC

Getting Started with MDC

Picture Mode

Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R)

Screen Adjustment

Auto Adjustment

Rotation

Aspect Ratio

Advanced Settings

Picture Options

Reset Picture

Network Settings

Network Status

Wi-Fi Direct

Soft AP

Allshare Settings

Device Name

Multi Control

Time

Menu Language

Rotate Menu

Eco Solution

Caption

Security

Pip

Auto Protection Time

Screen Burn Protection

Ticker

Video Wall

Source Autoswitch Settings

General

Anynet+ (HDMI-CEC)

DIVX® Video on Demand

Player Mode

Magic Clone

Reset System

Reset All

PC Module Power

Software Update

Contact Samsung

Contents Home

What Is Allshare Play

Using the Basic Allshare Play Features

My List

Videos

Photos

Music

Videos / Photos / Music Play Option Menu

Supported Subtitle and Allshare Play File Formats

File Formats Compatible with Magicinfo Lite Player

Approving a Connected Device from the Server

Magicinfo Lite

File Formats Compatible with Magicinfo Premium S Player

Approving a Connected Device from the Server

Magicinfo Premium S

File Formats Compatible with Magicinfo Videowall S Player

Magicinfo Videowall S

Customer Service Center

Requirements before Contacting Samsung Customer Service Center

Q & a

General