GE Monogram ZET837BYBB Installation Instructions Manual
30" convection built-in ovens
Hide thumbs
Also See for Monogram ZET837BYBB:
- Use and care manual (32 pages) ,
- Installation instructions manual (16 pages) ,
- Technician manual (29 pages)
Related Manuals for GE Monogram ZET837BYBB
Summary of Contents for GE Monogram ZET837BYBB
- Page 1 ® GE Monogram Installation Instructions 30" Convection Built-In Ovens Models ZET857SYSS ZET857DYSB ZET857BYBB ZET857WYWW ZET837SYSS ZET837DYSB ZET837BYBB ZET837WYWW...
-
Page 2: Table Of Contents
CAUTION: • This oven should be installed by a qualified installer or service technician. • Never use the oven for warming or heating a room. Prolonged use of the oven without adequate ventilation can be hazardous. Contents Design Information Models Available ... -
Page 3: Design Information
White double convection oven ZET837SYSS Stainless steel single convection oven ZET837DYSB Stainless steel on black single convection oven ZET837BYBB Black single convection oven ZET837WYWW White single convection oven Dimensions and clearances Design Information With both single and double built-in styles, contempo-... -
Page 4: Cabinet Style Options
To obtain optimal appearance, cabinet cutouts must be exact. The examples shown here illustrate typical styles of 30" cabinets and oven fit. Installation instructions for each of these basic cabinetr y styles are provided in this section. -
Page 5: Cabinetry
Adjacent Corners, Drawers, or Walls, etc. • Installing 12" from floor will place base of upper • These Monogram ovens require 3/4" overlap to • Oven overlaps will conceal raw edges on the top and 30" Built-I n Convection Oven s support oven. -
Page 6: Framed Cabinet Single Oven
• All Monogram ovens require 3/4" overlap on both sides. Allow 1" min. for top overlap and clearance to upper doors. • Oven overlaps will conceal raw edges on top and both sides of cutout. Single ovens can be installed below a countertop. Use the cutout dimensions shown on this page. -
Page 7: Frameless Cabinets
The front face of the oven will be flush with cabinetry doors or drawers. Whenever possible, order 30" frameless cabinet with the cutout sized to fit the oven. If you are using stock cabinets, additional finished filler pieces may be required to cover openings. -
Page 8: Installation
• The support must be level and rigidly mounted, flush with the bottom edge of the cutout. • The entire weight of the oven is supported by 2 x 4 runners or the solid floor and must be capable of supporting 300 lbs. -
Page 9: Electrical Supply
The free end of the green wire (the ground wire) must be connected to a suitable ground. This wire must remain grounded to the oven. • If cold water pipe is interrupted by plastic, non- metallic gaskets, union connections or other insulating materials, DO NOT use for grounding. -
Page 10: 208V Electrical Supply
If connecting to a 208 volt, 60 Hz., supply, a jumper must be used across two terminals. • For double ovens, there are two jumpers, one for the upper oven, one for the lower oven. • For single ovens there is one jumper. Loosen Screws... -
Page 11: Step 3: Remove Oven Doors
Caution: Route into the opening. Ovens have side handles. Grasp side handle with one cable hand and into oven opening with other hand. Lift the oven to the through cabinet opening, very carefully. cutout With oven in front of cabinet opening: •... -
Page 12: Step 6: Replace The Oven Door
• Slide the hinge slots in the bottom of the door over oven door the hinges. • Push the door all the way in against oven. • Open the door fully and push hinge latches down, as illustrated, on both sides to secure. -
Page 13: Determine Need For Filler Panels
The oven support floor and supports should be installed at the required locations. If there is a gap between the oven support floor and the bottom of the opening, a bottom filler panel should be constructed to fill the gap. -
Page 14: Cut Rail For Filler Panel
• The appearance panel width should match drawer fronts or doors. • Make the appearance panel appropriate height to fill the gap above or below the oven, allowing for reveals and overlaps to match existing drawers or doors. Determine... -
Page 15: Cut And Secure Cleats To Filler Panel
• Place filler panel in proper position. To attain proper relationship to adjacent drawers and doors Cabinetry Modification Suggestions 30" Built-I n Convection Oven s For the bottom filler panel: • Cut 2 cleats out of 3/4" thick material, approxi- mately 1-1/4"... - Page 16 Monogram. ® General Electric Company Louisville, KY 40225 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night.