Table of Contents
Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment to an outlet on a circuit other than that to which the receiver is connected
Consult the dealer or and experienced radio/TV technician for help
SMART-LIFT™ Electric Ceiling Lift
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
SL236i
Advertisement
Table of Contents
Related Manuals for CHIEF SMART-LIFT SL236i
Summary of Contents for CHIEF SMART-LIFT SL236i
- Page 1 Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment to an outlet on a circuit other than that to which the receiver is connected Consult the dealer or and experienced radio/TV technician for help SL236i...
-
Page 2: Disclaimer
It is the installer’s responsibility to make sure the weight of all When using an electrical mounting system, basic precautions components attached to the SL236i does not exceed 35 lbs should always be followed, including the following: (15.9 kg). -
Page 3: Tools Required For Installation
Installation Instructions SL236i TOOLS REQUIRED FOR INSTALLATION PARTS A (1) [Ceiling lift] (SL236FDi Shown) J (1) [Power cord] B (1) [Push button assembly] C (5) D (1) [4" cable tie] [External terminal cover plate] E (1) [Jumper wire] F (5) -
Page 4: Table Of Contents
Allentare il fissaggio Bevestiging losdraaien Afstellen Ajuster Desserrez les fixations TABLE OF CONTENTS Installing in a Wood Framework (Joists)..9 Disclaimer.............2 Installing Projector on SL236i......9 Tools Required For Installation......3 Adjustments..........10 Parts..............3 Routing Cables..........11 Legend............4 Connecting Control Wiring......12 Dimensions........... 5 Connecting to Power Supply......12 Installation Requirements......6... -
Page 5: Dimensions
Installation Instructions SL236i DIMENSIONS SL-236FDi [520.7] 20.50 [260.4] 10.25 [732.8] 28.85 [584.2] 23.00 [698.5] MAXIMUM AVAILABLE SPACE FOR 27.50 PROJECTOR AND EQUIPMENT HxWxD = 9.25 x 20.50 x 22.75 INCHES [235.0 x 520.7 x 577.9mm] [635.0] 25.00 [669.3] [16.5] 26.35 [19.1]... -
Page 6: Installation Requirements
Attach supports (not provided) to the top of lift. assembly (B) to contacts 1 (red) and 6 (black). (See (See Figure 1) Figure 3). Plug the SL236i test inlet in using the supplied 6 ft. power cord (J). (See Figure 2) Supports NOTE:... -
Page 7: Power Requirements And Wiring
Installation Instructions SL236i Press the push button (B) to test the SL236i while it is still in the pre-test position. • Press when the lift is at its top position and it will move Internal down. wiring terminal • Press when the lift is at its bottom position and it will move up. - Page 8 Secure the threaded rods to the SL236SPi with Grade 2 or better 3/8 in. jam nuts (not provided) and washers (one of each on inside and one of each on outside--not provided). (Top view of SL236i) Insert rods into 3 slots...
-
Page 9: Installing In A Wood Framework (Joists)
The lift MUST be installed square and parallel. the ceiling tile retainer. Do NOT stress or bend the lift during installation. Use the provided push button (B) to operate the SL236i up and down, ensuring that all clearances are adequate. CAUTION: Do NOT allow parts of ceiling tile or grid to protrude from the ceiling panel. -
Page 10: Adjustments
Press in end tabs on both ends of yaw adjustment bracket Adjustments and lock into place. (See Figure 11) TRAVEL (SHOW ADJUSTMENT) Remove the yaw adjustment bracket from the SL236i by lifting up. (See Figure 11) CAUTION: Do not overadjust (exceed maximum) travel length. -
Page 11: Routing Cables
Damage may result when lift is • Tighten nuts. (See Figure 15) raised. Lower SL236i to service position. Route and secure electrical and video cables using installed cable clips (See Figure 17) • Remove nut and open cable clip. -
Page 12: Connecting Control Wiring
RUNNING OR IN COOLING MODE! Premature bulb failure or damage to electrical components may occur if lift closes. NOTE: If SL236i is cycled up and down repeatedly the motor’s thermal overload protection will stop operation. Operation will resume when the thermal overload resets (usually within 3 to 5 minutes). -
Page 13: Table 1: Wiring Table
Installation Instructions SL236i Table 1: WIRING TABLE EXTERNAL WIRING INTERNAL WIRING Figure 18 NOTE: The numbers listed in the SL236i Internal and SL236i External columns refer to the corresponding numbers located where indicated in the wiring pictures. (See Figure 18) -
Page 14: Table 2: Internal Terminal Descriptions
SL236i Installation Instructions Table 2: INTERNAL TERMINAL DESCRIPTIONS... -
Page 15: Descriptions
Installation Instructions SL236i Figure 19... - Page 16 SL236i Installation Instructions...
- Page 17 Installation Instructions SL236i...
- Page 18 SL236i Installation Instructions...
- Page 19 Installation Instructions SL236i...
- Page 20 A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a products division P +31 (0)40 2668620 of Milestone AV Technologies F +31 (0)40 2668615 Asia Pacific A Office No.
Need help?
Do you have a question about the SMART-LIFT SL236i and is the answer not in the manual?
Questions and answers