Table of Contents
Advertisement
Operation Guide 3260 3280
Configuring Home City Settings
There are two Home City settings: actually selecting the
City name
City name
Home City and selecting either standard time or daylight
saving time (DST).
To configure Home City settings
1. In the Timekeeping Mode, hold down
starts to flash and the city name starts to scroll on the
display.
Hour : Minutes
Hour : Minutes
PM indicator
PM indicator
Seconds
Seconds
•
This is the setting screen.
•
The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
•
For details about city names, see the "City Code
Table" at the back of this manual.
DST indicator
DST indicator
E-40
5. After all the settings are the way you want, press
Mode.
•
The DST indicator appears to indicate that Daylight Saving Time is turned on.
Note
•
After you specify a city name, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current
time in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping.
The reference point for UTC is Greenwich, England.
•
Selecting some city names automatically makes it possible for the watch to
receive the time calibration signal for the corresponding area. See page E-21
for details.
E-42
4. After all the settings are the way you want, press
Mode.
•
The DST indicator appears to indicate that Daylight Saving Time is turned on.
E-44
3. Press
to move the flashing in the sequence shown below to select the other
settings.
12/24-Hour
City Name
DST
Seconds
Format
Thermometer
Illumination
Power Saving
unit
Duration
•
The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use
change it as described below.
Screen
To do this:
Change the city name
Cycle between Auto DST (AUTO), Daylight
Saving Time (On) and Standard Time (OFF).
E-46
•
While 12-hour format is selected for timekeeping, a P (PM) indicator will appear
for times from noon to 11:59 p.m. No indicator appears for times from midnight
to 11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without
any P (PM) indicator.
•
The watch's built-in full automatic calendar makes allowances for different
month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the watch's rechargeable battery
replaced or after power drops to Level 5 (page E-14).
E-48
until SET
to return to the Timekeeping
to return to the Timekeeping
Hour
Minutes
Year
Button Operation
Day
Month
Tone On/Off
and/or
to
Do this:
Use
(East) and
(West).
Press
.
2. Press
(East) and
(West) to select the city name you want to use as your
Home City.
•
Keep pressing
or
until the city name you want to select as your Home
City appears on the display.
3. Press
to display the DST setting screen.
4. Use
to cycle through the DST settings in the sequence shown below.
Auto DST (AUTO)
DST off (OFF)
•
The Auto DST (AUTO) setting will be available only when a city name that
supports time calibration signal reception (page E-21) is selected as the Home
City. While Auto DST is selected the DST setting will be changed automatically
in accordance with time calibration signal data.
•
Note that you cannot switch between standard time and daylight saving time
(DST) while UTC is selected as your Home City.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
starts to flash and the city name starts to scroll on the
display.
•
This is the setting screen.
2. Press
to display the DST setting screen.
3. Use
to cycle through the DST settings in the
sequence shown below.
DST indicator
DST indicator
Auto DST (AUTO)
•
The Auto DST (AUTO) setting will be available only
when a city name that supports time calibration
signal reception (page E-21) is selected as the
Home City. While Auto DST is selected the DST
setting will be changed automatically in accordance
with time calibration signal data.
Configuring Current Time and Date Settings Manually
You can configure current time and date settings manually when the watch is unable
to receive a time calibration signal.
To change the current time and date settings manually
1. In the Timekeeping Mode, hold down
City name
City name
starts to flash and the city name starts to scroll on the
display.
•
This is the setting screen.
2. Use
and
•
Select your Home City name before changing any
other setting.
Hour : Minutes
Hour : Minutes
•
For full information on city names, see the "City
PM indicator
PM indicator
Seconds
Seconds
Code Table" at the back of this manual.
Screen
To do this:
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping.
Reset the seconds to 00
Change the hour or minutes
Change the year, month, or day
5. Press
to exit the setting screen.
Note
•
For information about selecting a Home City and configuring the DST setting,
see "Configuring Home City Settings" (page E-40).
Digital Compass
A built-in bearing sensor detects magnetic north at regular intervals and indicates one
of 16 directions on the display.
•
The watch also takes temperature readings in the Digital Compass/Thermometer
Mode. For more information, see "Thermometer" (page E-73).
DST on (On)
E-41
until SET
DST off (OFF)
DST on (On)
E-43
until SET
to select the city name you want.
E-45
Do this:
Press
.
Press
.
Use
(+) and
(–).
E-47
E-49
Hide quick links:
Advertisement
Table of Contents
