Table of Contents
Advertisement
Operation Guide 5176
Screen
To do this:
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping.
Reset the seconds to 00
Change the hour or minute
Change the year, month, or day
5. Press
to exit the setting screen.
E-20
Hand Home Position Correction
The hour and minute hands of the watch can be thrown off by exposure to strong
magnetism or impact. The watch is designed to correct the hour and minute hand
positions manually.
•
All of the operations in this section are performed in the Hand Setting Mode, which
you enter by pressing
(page E-11).
To adjust home positions
1. In the Hand Setting Mode, hold down
Hour and minute hands
Hour and minute hands
seconds until 0:00 appears on the display.
•
This is the home position adjustment mode.
2. Check the positions of the hour and minute hands.
•
The hands are in the correct home positions if they are
pointed at 12 o'clock. If they aren't, use
and
(counterclockwise) to adjust their positions.
3. Press
to exit the setting screen.
Correct hour and
Correct hour and
•
This will cause the hour and minute hands to move to
minute hand positions
minute hand positions
the current Timekeeping Mode time.
E-22
2. Press
fi ve times to return to the Timekeeping Mode.
•
The watch will return to the Timekeeping Mode automatically if you do not perform
any operation for about one hour after entering the Barometer/Thermometer Mode.
Barometric Pressure
•
Barometric pressure is displayed in units of 1 hPa (or 0.05 inHg).
•
The displayed barometric pressure value changes to - - - if a measured barometric
pressure falls outside the range of 260 hPa to 1,100 hPa (7.65 inHg to 32.45 inHg).
The barometric pressure value will reappear as soon as the measured barometric
pressure is within the allowable range.
Temperature
•
Temperature is displayed in units of 0.1°C (or 0.2°F).
•
The displayed temperature value changes to --.- °C (or °F) if a measured
temperature falls outside the range of –10.0°C to 60.0°C (14.0°F to 140.0°F). The
temperature value will reappear as soon as the measured temperature is within the
allowable range.
E-24
Reading Barometric Pressure Differential Pointer
Pressure differential is indicated in the range of ±5 hPa, in 1-hPa units.
If the pointer is located here:
CLOUDY (–)
Pressure is falling and weather will tend to deteriorate.
FINE (+)
Pressure is rising and weather will tend to improve.
•
The nearby screen shot, for example, shows what the pointer would indicate when
the calculated pressure differential is approximately – 3 hPa (approximately – 0.09
inHg).
0.15
−0.15
hPa values
inHg values
E-26
To calibrate the pressure sensor and the temperature sensor
1.Take a reading with another measurement device to
determine the exact current barometric pressure or
temperature.
2. With the watch in the Timekeeping Mode, press
enter the Barometer/Thermometer Mode.
3. Hold down
to fl ash on the display. This is the setting screen.
•
Before the temperature value starts to fl ash, the
message SET Hold will appear on the display.
Keep
depressed until SET Hold disappears.
4. Press
to move the fl ashing between the temperature
value and barometric pressure value, to select the one
you want to calibrate.
E-28
Do this:
Press
.
Press
.
Use
(+) and
(–).
for about two
(clockwise)
It means this:
Current pressure greater than
most recent measured pressure
Current pressure less than most
recent measured pressure
to
until the current temperature value starts
Note
•
For information about selecting a Home City and confi guring the DST setting, see
"Confi guring Home City Settings" (page E-14).
•
While 12-hour format is selected for timekeeping, a P (PM) indicator will appear for
times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any P
(PM) indicator.
•
The watch's built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch's battery replaced.
Barometer/Thermometer
This watch uses a pressure sensor to measure air pressure (barometric pressure) and
a temperature sensor to measure temperature.
To enter and exit the Barometer/Thermometer Mode
Pressure
Pressure
Current time
Current time
differential
differential
1. While in the Timekeeping Mode, press
pointer
pointer
Barometer/Thermometer Mode.
•
BARO will appear on the display, indicating
that barometric pressure and temperature
measurements are in progress. The measurement
results will appear on the display after about fi ve
seconds.
•
After you press
fi ve seconds for the fi rst three minutes, and then
Temperature
Temperature
every two minutes after that.
Barometric
Barometric
pressure
pressure
Display Units
You can select either hectopascals (hPa) or inchesHg (inHg) as the display unit for the
measured barometric pressure, and Celsius (°C) or Fahrenheit (°F) as the display unit
for the measured temperature value. See "To specify temperature, barometric
pressure, and altitude units" (page E-39).
Barometric Pressure Differential Pointer
This pointer indicates the relative difference between
Barometric
Barometric
the most recent barometric pressure reading and the
pressure
pressure
differential
differential
current barometric pressure value displayed in the
pointer
pointer
Barometer/Thermometer Mode (page E-23).
•
Barometric pressure is calculated and displayed using hPa as the standard. The
barometric pressure differential also can be read in inHg units as shown in the
illustration (1 hPa
0.03 inHg).
Pressure Sensor and Temperature Sensor Calibration
The pressure sensor and temperature sensor built into the watch are calibrated at the
factory and normally require no further adjustment. If you notice serious errors in the
pressure readings and temperature readings produced by the watch, you can calibrate
a sensor to the reading of another device to correct the errors.
Important!
•
Incorrectly calibrating the temperature sensor can result in incorrect readings.
Carefully read the following before doing anything.
– Compare the readings produced by the watch with those of another reliable and
accurate thermometer.
– If adjustment is required, remove the watch from your wrist and wait for 20 or 30
minutes to give the temperature of the watch time to stabilize.
5. Use
(+) and
(–) to adjust the calibration value in the units shown below.
Temperature
0.1°C (0.2°F)
Barometric Pressure
1 hPa (0.05 inHg)
•
To return the currently fl ashing value to its initial factory default setting, press
and
at the same time. OFF will appear at the fl ashing location for about one
second, followed by the initial default value.
6. Press
to return to the Barometer/Thermometer Mode screen.
Barometer and Thermometer Precautions
•
The pressure sensor built into this watch measures changes in air pressure, which
you can then apply to your own weather predictions. It is not intended for use as a
precision instrument in offi cial weather prediction or reporting applications.
•
Sudden temperature changes can affect pressure sensor readings.
•
Temperature measurements are affected by your body temperature (while you are
wearing the watch), direct sunlight, and moisture. To achieve a more accurate
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe all moisture from the case. It
takes approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.
E-21
to enter the
, the watch will take readings every
E-23
E-25
E-27
E-29
Hide quick links:
Advertisement
Table of Contents
