Audio Output Settings; Operation And State Display Settings - Sanyo DVR-HT120 Instruction Manual

Audio Output Settings

1. Turn the TV on and select input from the DVD recorder. (For details
on operation methods, refer to your TV's manual.)
2. Press SYSTEM MENU to display the System Menu.
3. Select "Sound" using 8 or 2, and press 6 once. The setting items
at "Sound Options" on the right of the screen can now be selected
using 8 or 2.
4. Select the item to be changed using 8 or 2, and change the set-
tings.
System Menu
Video
Sound
Feature
Language
Recording
Setup
Setting Item
Digital Set output from the digital audio output terminal.
Output When you press the k button, the selection items
are displayed. Select digital output using 8 or 2, and
press the k button.
Off
PCM Only Dolby Digital and MPEG-2 multi-channel
All
Analog Set output from the analogue audio output terminal
Output (L/R AUDIO OUT).
When you press the k button, the selection items
are displayed. Select analogue output using 8 or 2,
and press the k button.
Stereo
Surround Dolby Digital and MPEG-2 multi-channel
Night Mode Night mode optimises the sound for playback at low
volume. You are therefore less likely to disturb your
neighbours. This only works for Dolby Digital audio on
DVD video discs. This option can be selected if required.
Night Mode works only when analog output.
To use this feature, press the k button to select it.
Each press of k selects or deselects this setting.
NOTE:
- When you press 4 , other items in the System Menu can be selected.
Set other items as necessary.
5. To end setting, press SYSTEM MENU.
Sound Options
Digital Output All
Analog Output
Stereo
Night Mode
Explanation
Select this when digital audio output is not
used.
signals are converted to PCM (Pulse Code
Modulation). This setting is for receiv-
ers/amplifi ers without digital multi-channel
sound decoders. DTS is not converted into
PCM. (Sound does not output.)
Dolby Digital and DTS signals are fed
unaltered to the digital output. MPEG-2
multi-channel signals are converted to
PCM (Pulse Code Modulation). This set-
ting is for receivers/amplifi ers with digital
multi-channel sound decoders.
For devices without DolbySurround or
TruSurround. Use this setting if the DVD
recorder is connected only to a stereo TV
set.
are mixed down to a DOLBY surround-
compatible two-channel output signal. For
devices with Dolby Surround Pro Logic
decoder.

Operation and State Display Settings

1. Turn the TV on and select input from the DVD recorder. (For details
on operation methods, refer to your TV's manual.)
2. Press SYSTEM MENU to display the System Menu.
3. Select "Feature" using 8 or 2, and press 6 once. The setting items
at "Feature Options" on the right of the screen can now be selected
using 8 or 2.
4. Select the item to be changed using 8 or 2, and change the set-
tings.
System Menu
Video
Sound
Access Control
Status Display
Feature
Resume
Language
Auto Standby
Recording
Clock Display: Off
PBC Enable
Setup
Setting Item
Access Parental Level Control
Control Accessing of DVD discs can be controlled.
For details, see "Parental Level Control" on page 34.
Status Along with the on-screen menu, the OSD (On Screen
Display Display) also displays information on the current operat-
ing status (counter, playback, recording, TV channel,
etc.) on the TV screen. By default, this would be off, to
see the information about the operating status, check
the "Status Display" box. This appears in every selected
mode for a few seconds and disappears.
To use this feature, press the k button to select it.
Each press of k selects or deselects this setting.
Resume If playback of a pre-recorded DVD video disc is inter-
rupted (rOPEN/CLOSE), when the disc is reloaded
(disc is started), playback starts at the precise location
where it stopped. This applies not only to the current
disc but to the last 20 discs played. This feature can
be switched off if not required.
To use this feature, press the k button to select it.
Each press of k selects or deselects this setting.
Auto To set whether or not to set the standby mode when
Standby no operations have been performed for 10 minutes.
When no DVD recorder operation has occured for
10 minutes after e(STOP) button is pressed , this
unit will go to standby mode. This function works CD
media(Audio, MP3 or JPEG) only.
To use this feature, press the k button to select it.
Each press of k selects or deselects this setting.
Clock To save power, you can switch off the clock display on
Display: Off the DVD recorder. Programmed (TIMER) recordings
will still take place.
If the recorder is switched off (button o), the clock
display is also switched off when checked.
If the recorder is switched off (button o), the
clock display is visible when unchecked.
To use this feature, press the k button to select it.
Each press of k selects or deselects this setting.
NOTE:
- When you press 4, other items in the System Menu can be selected.
Set other items as necessary.
5. To end setting, press SYSTEM MENU.
Feature Options
Press OK
Explanation
32