Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fujitsu FTP-628WSL210 Series
Summary of Contents for Fujitsu FTP-628WSL210 Series
-
Page 1: Mobile Printer
Mobile Printer FTP-628WSL210 Series User's Guide FUJITSU COMPONENT LIMITED... - Page 3 Thank you for purchasing the FTP-628WSL210 Series Mobile Printer hereafter referred to as “this product”). This User's Guide (hereafter referred to as “this guide”) contains precautions to use it safely and correctly. Before using this product, please read the complete this guide.
- Page 4 ■ Copyright This product and this guide are copyrighted works of FUJITSU COMPONENT LIMITED. This product and this manual must not be reproduced, duplicated, used, or modified, partially or in full, without permission.
-
Page 5: Regulatory Compliance
■ Regulatory Compliance For Customers in USA (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. - Page 6 For Customers in CANADA (Industry Canada) This equipment complies with Industry Canada RSS210 rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. For Customers in EU (CE Marking) This product is in conformance with the requirements of European Council Directive:...
-
Page 7: Explanation Of Symbols
■ Explanation of Symbols The following symbols are used in this guide. Please read and nderstand the meaning of each symbol in this guide. If this product should malfunction, immediately stop using it, and contact your sales representative. Indicates an imminent risk of causing severe Danger personal injury or death if not used properly. -
Page 8: General Cautions
■ General Cautions Warning - Do not use in the environment with corrosive gas or salt wind is present. Break- down Failure to observe this may cause failure. - Do not modify or disassemble. Failure to observe this may cause fire, explosion or Modify breakdown. - Page 9 Caution - Do not use while driving a vehicle or walking. Failure to observe this may cause traffic accidents and Injury injuries. - Do not use the printer near the equipment that generates large radiation noise, such as a high voltage Break- down device and a large motor.
- Page 10 ■ Printer Warning - Do not use the printer in a location where radio wave generation is prohibited. Accident Might cause accidentally a malfunction of the instrument. - During or immediately after operation, do not touch the print head, the support plate and the motor. Heat is not Burn immediately discharged.
- Page 11 ■ Battery Warning - Do not use the battery for other device or purpose. Failure to observe this may cause destruction. Break- down - Do not disassemble the battery. Failure to observe this may cause heat, fire or destruction. Modify - Only use the specified battery.
- Page 12 ■ AC Adapter Warning - Do not use the AC adapter for any other devices or purposes. Break- down Failure to observe this may cause damage to the printer and/or battery. - Only connect the AC adapter to the specified voltage and/or frequency.
- Page 13 ■ Warning Label of Product This product comes with the following warning label. This label must not be peeled off or erased from the display. Moreover, please contact the distributor when the label is difficult to see due to dirt, scratching etc. Warning display Content HEAD...
-
Page 14: Table Of Contents
1 Types of Product .............13 2 Preparation to Print ............14 Packaging .............14 Optional Accessories..........15 Getting to Know the Printer ........16 Inserting the Battery ..........19 Connecting AC Adapter (Charging)......20 Connecting AC Adapter (Operating)......21 Inserting the Paper ..........22 Attaching the Belt Clip ..........23 3 Operating Procedures ............24 Power On..............24 Test Print ..............25... -
Page 15: Types Of Product
1 Types of Product Types of Product Types of Product The following product types are available. Please note that the printer may not support the function of the printer model, even if there is a description in this guide. MODEL NAME F T P - 6 2 8 W S L 2 1 0 # 2 0 - R a : Supply item (Refer to Table 1-1) -
Page 16: Preparation To Print
2 Preparation to Print Preparation to Print Preparation to Print 2.1 Packaging The following items are included. If anything is missing, please contact the distributor. Printer Battery AC adapter Safety Cautions... -
Page 17: Optional Accessories
2 Preparation to Print 2.2 Optional Accessories The following optional parts are available. Purchasing information for these accessories can be obtained from the place where you bought this printer. Paper Battery AC adapter AC cable USB cable Belt Clip (PSE or UL/CSA) -
Page 18: Getting To Know The Printer
2 Preparation to Print 2.3 Getting to Know the Printer ■ Front Side (Cover Closed) Paper Cover : Cover to open and load paper. Paper Cutter : To cut paper. Status LED : Displays status of the printer. POWER Switch : To turn the power supply ON or OFF. - Page 19 2 Preparation to Print ■ Front Side (Cover Open) Platen Roller : To feed paper. Warning Label : This shows warning when using printer. Thermal Head : This applies heat to paper. Paper Sensor : This sensor detects the status of paper.
-
Page 20: Rear Side
2 Preparation to Print ■ Rear Side Screw for Belt Clip : This attaches the Belt Clip. AC Adapter Jack : Open and connect AC adapter. Product Label : Displays printer type and other product information. -
Page 21: Inserting The Battery
2 Preparation to Print 2.4 Inserting the Battery Caution Life of the battery is about 500 charges. (At the normal temperature) If an old battery is used, not only the equipment malfunctions and this might cause destruction. 1. Please push cover lock and lift the battery cover to open. -
Page 22: Connecting Ac Adapter (Charging)
2 Preparation to Print 2.5 Connecting AC Adapter (Charging) T he battery is charged by the printer's built-in charger. Caution Please stop charging immediately if an abnormal charge is generated. 1. Please connect the AC cable with the AC adapter, and connect the AC plug to an outlet. -
Page 23: Connecting Ac Adapter (Operating)
2 Preparation to Print 2.6 Connecting AC Adapter (Operating) T his product can also be operated with the AC adapter. 1. Please connect the AC cable with the AC adapter, and connect the AC plug with AC cable AC adapter the outlet. -
Page 24: Inserting The Paper
2 Preparation to Print 2.7 Inserting the Paper 1. Please push up the cover open lever to open the paper cover. Cover Open Lever Thermal Paper (Thermosensitive Side) 2. Please insert the paper in the printer. 3. Please put out the edge of the paper and close the paper cover. -
Page 25: Attaching The Belt Clip
2 Preparation to Print 2.8 Attaching the Belt Clip The printer can be attached to the waist belt with a Belt Clip. Below are recommendations how to attach the Belt Clip: How to attach it 1. Please remove the screw for the Belt Clip on the back of the printer. -
Page 26: Operating Procedures
3 Operating Procedures 3.1 Power On 1. Please push the POWER Switch until the LED light turns green. 2. It is possible to turn the power off by pushing the POWER Switch until the LED turns off. -
Page 27: Test Print
3 Operating Procedures 3.2 Test Print This product has a test print function. The setting of the printer can be confirmed by this test rint. 1. Please turn the power off and push the FEED switch. 2. Please turn the power on while holding with the FEED switch down. - Page 28 3 Operating Procedures Check pattern The thermal head open circuit etc. can be confirmed. Version The firmware version can be confirmed. ---------------- Setting information etc 628AD Ver 1.00 ---------------- The setting information etc can be confirmed. This print example Serial No : 22000001 shows the following content.
-
Page 29: Usb Communication
3 Operating Procedures 3.3 USB Communication Explanation of how to communicate and print with a USB able from a terminal such as a personal computer: 1. Please use the USB cable. The plug on the printer side (device side) is the mini B type. 2. -
Page 30: Bluetooth Communication
3 Operating Procedures 3.4 Bluetooth Communication Explanation of how to communicate and print with a Bluetooth device from a terminal such as a personal omputer: 1. Please turn the printer on. 2. Please find the Bluetooth device in the host terminal. 3. -
Page 31: Printer Error
3 Operating Procedures 3.5 Printer Error The error occurs when the printer cannot print/work normally. The type of error is shown by the LED when the error is occurring. Please reset the status when the error occurs. The following example explains reasons and solutions for problems. - Page 32 3 Operating Procedures Error Cause Solution Supply Voltage - The battery charge is - Please charge Error low. the battery. - The AC adapter is out - Please exchange of order. (At the AC the AC adapter. adapter operation) Mark - The mark of paper is - Please use the paper Undetection...
-
Page 33: Indicator Lights
4 Indicator Lights The LED displays printer error and the low battery status. Important It may be difficult to see the LED display in a bright place such as in direct sunshine etc. 4.1 Normal Operation LED Indications (LED Symbol ○ :Lighting, ● :Blinking) Printer Status Blink Cycle ... -
Page 34: Printer Error
4 Indicator Lights 4.2 Printer Error LED Indications (LED Symbol ○ :Lighting, ● :Blinking) Printer Status Blink Cycle (Unit [msec]) Gree n Ora nge Re d ● Paper End 1time 1000 O FF ● Paper Cover Open 1 000 2times O FF Thermal Head... -
Page 35: Charging
4 Indicator Lights 4.3 Charging LED Indications (LED Symbol ○ :Lighting, ● :Blinking) Printer Status Blink Cycle (Unit [msec]) Gree n Ora nge Re d Chargeing ○ Char ging O FF Full Charge Cha rging Full charge O FF Charge Error (Over charge, ●... -
Page 36: Maintenance
5 Maintenance P lease service this printer regularly. Caution - Do not service the printer while the battery is inserted or the AC adapter connected. - Do not completely service, disassemble and repair any parts that are not explained in this chapter. 5.1 Thermal Head Please service the thermal head once a month. -
Page 37: Platen Roller
5 Maintenance 5.2 Platen Roller Please service the platen roller once a month. 1. Please open the paper cover. (Refer to chapter 2.7) 2. Soak a cotton ball with some alcohol and wipe the platen roller gently until it is clean. Please use isopropyl alcohol. 3. -
Page 38: Paper Cover
5 Maintenance 5.4 Paper Cover If the paper cover comes off, please repair it according to the following instructions. 1. Please push the opening and closing fulcrum of the paper cover to the printer with the paper cover opened, and it connects the printer. -
Page 39: Power/Feed Switch
5 Maintenance 5.5 POWER/FEED Switch If the Power switch or the FEED switch falls off, please repair according to the following instructions. 1. Please push the power switch back into its round hole. Please push the FEED switch back into its oval hole. Switch <Front view>... -
Page 40: Troubleshooting
6 Troubleshooting ■ Power Problem Cause Solution Printer does not Is a battery inserted? or Please insert the battery turn on Is it inserted reversed? correctly. (C. 2.4) battery fully Please charge charged? the battery. (C. 2.5) Is the POWER Switch Please push the POWER correctly pushed? Switch correctly. - Page 41 6 Troubleshooting ■ Communication Problem Cause Solution Printer does not Is the power turned off? Please turn on the communicate power. (C. 3.1) Is the application or the Please use the driver for this product application or the driver used? for this product.
- Page 42 6 Troubleshooting ■ Print Problem Cause Solution Printer does not Is the power turned off? Please turn on the feed the paper power. (C. 3.1) Is the paper correctly Please insert the paper Paper jam inserted? correctly. (C. 2.7) occurs Is the paper cover Please close the paper closed?
- Page 43 6 Troubleshooting ■ Others Problem Cause Solution Print starting Does the mark detection Please remove the location is operate correctly? reason for the mark incorrect (C. 4.2) detection error. (C. 3.5) Printing is slow Is the battery charge Please charge low? the battery.
-
Page 44: Specifications
7 Specifications 7.1 Printer Specifications Items Contents Print Method Thermal Line-dot Printing Resolution 8dot/mm (203dpi) Dimensions 84×136.5×43.6mm Weight About 220g Including battery, excluding paper Max Print Width About 48mm Print Speed Max 40mm/sec Battery full charge, print ratio 12.5% Character Alphanumeric, Katakana : 8x16, 16x16, 12x24, 24x24 Kanji... -
Page 45: Paper Specifications
7 Specifications 7.2 Paper Specifications Items Contents Type Thermal Roll Paper Width Outer Up to φ36mm Diameter Inner φ 8mm or more Diameter Thickness 60 to 80μm Specified Type Name Manufacture Paper High Sensitive TF50KS-E4 Nippon Paper Group Standard Paper TF60KS-E Nippon Paper Group PD150R Oji Paper Group... -
Page 46: Recycle
8 Recycle This symbol means: Do not dispose of this product together with your household waste! Please refer to your local community or contact our dealers to properly handle the end-of-life of electric and electronic equipment. Recycling this product will help to conserve natural resources and prevent potential negative impact on the environment and human ealth caused by inappropriate handling. -
Page 47: Appendix
9 Appendix 9.1 Bluetooth Communication (1) Android Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - " WIRELESS ＆ NETWORKS" from the menu of terminal, and turn on Bluetooth. 3. Please open the "Bluetooth”, and tap "FTP-628WSL…". (Please tap "SEARCH FOR DEVICES", if it does not appear) 4 Please input the PIN code, and tap "OK". - Page 48 9 Appendix (2) iOS Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - "General" - "Bluetooth" from the menu of terminal, and turn on Bluetooth. 3. Please tap "FTP-628WS…" from "Devices". 4. Please input the PIN code, and tap "Pair". PIN code is "9999"...
-
Page 49: Product Support
Moreover, when you request repair, please provide the model name and the product serial number in addition to information on the actual failure etc. T chnical Support Section FUJITSU COMPONENT LIMITED (Japan) Global Marketing Dept.2 Tel: +81-3-5449-7014 Fax: +81-3-5449-2628 E-mail: promothq@fcl.fujitsu.com... - Page 51 Mobile Printer FTP-628WSL210 Series U ser's Guide L0NA02265-L11802RS Published by FUJITSU COMPONENT LIMITED Nov. 2012 Rev. 1...