Advertisement

Battery Charger User Manual

IMPORTANT SAFETY INSTRUCTIONS

Read All Instructions
SAVE THESE INSTRUCTIONS
PRO CHARGER 250
This manual contains important safety and operating
instructions for Snap-on PRO CHARGER 250 Battery Charger
model EEBC302A. Refer to the information in this manual often
for safe operation.
Read, understand and follow all safety messages and
instructions in this manual and on the test equipment. Safety
messages in this section of the manual contain a signal word, a
three-part message, and, in some instances, an icon.
The signal word indicates the level of hazard in a situation:
• Danger indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury to the
operator or bystanders.
• Warning indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury to the
operator or bystanders.
• Caution indicates a potentially hazardous situation which, if
not avoided, may result in moderate or minor injury to the
operator or bystanders.
The three-part message uses three different type styles to
further define the potential hazard.
• Normal type states the hazard.
• Bold type states how to avoid the hazard.
• Italic type states the possible consequences of not avoiding
the hazard.
An icon, when present, gives a graphical description of the
potential hazard.
EEBC302A
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRO CHARGER 250 EEBC302A and is the answer not in the manual?

Questions and answers

James Scott rager
January 21, 2025

Is there any parts available for charger

1 comments:
Mr. Anderson
February 4, 2025

Yes, the following parts are available for the Snap-On PRO CHARGER 250 EEBC302A:

- Rectifier Assembly (Part Number: BC4200-2000R)
- Transformer Assembly (Part Number: EAT0003K11AR)
- Fan Blade (Part Number: 2-1268)
- Fan Motor (Part Number: 2-10166-1)
- DC Leads with Clamps (Part Number: BC4200-100R)
- DC Circuit Breaker (Part Number: 2-15366)
- AC Circuit Breaker (Part Number: 2-10266)
- Ammeter (Part Number: 4-280)
- Power Cord (Part Number: 6-2821)
- Range Switch (Part Number: 2-9958)
- Charge Timer (Part Number: 2-14866)
- Knob, Charge Timer (Part Number: 8-8230)
- Foot with 4 Screws (Part Number: EAK0073K27A)
- Wheel Kit (Part Number: EAK0073K26A, includes 2 wheels, 2 push nuts, and axle).

This answer is automatically generated

James Scott rager
January 21, 2025

Is there any parts available

1 comments:
Mr. Anderson
February 4, 2025

Yes, the following parts are available for the Snap-On PRO CHARGER 250 EEBC302A:

- Rectifier Assembly (Part Number: BC4200-2000R)
- Transformer Assembly (Part Number: EAT0003K11AR)
- Fan Blade (Part Number: 2-1268)
- Fan Motor (Part Number: 2-10166-1)
- DC Leads with Clamps (Part Number: BC4200-100R)
- DC Circuit Breaker (Part Number: 2-15366)
- AC Circuit Breaker (Part Number: 2-10266)
- Ammeter (Part Number: 4-280)
- Power Cord (Part Number: 6-2821)
- Range Switch (Part Number: 2-9958)
- Charge Timer (Part Number: 2-14866)
- Knob, Charge Timer (Part Number: 8-8230)
- Foot with 4 Screws (Part Number: EAK0073K27A)
- Wheel Kit (Part Number: EAK0073K26A, includes 2 wheels, 2 push nuts, and an axle)

This answer is automatically generated

Summary of Contents for Snap-On PRO CHARGER 250 EEBC302A

  • Page 1: Important Safety Instructions

    PRO CHARGER 250 Battery Charger User Manual IMPORTANT SAFETY INSTRUCTIONS This manual contains important safety and operating instructions for Snap-on PRO CHARGER 250 Battery Charger model EEBC302A. Refer to the information in this manual often for safe operation. Read All Instructions Read, understand and follow all safety messages and instructions in this manual and on the test equipment.
  • Page 2: Safety Information

    Safety Information Battery Gases, Charging Preparation and Charger Location Risk of explosion. Gases produced by a battery are highly explosive. • Wear safety goggles and protective clothing, user and bystander. • Use charger in an area having at least 4 air changes per hour.
  • Page 3 • Do not operate charger after a sharp impact, dropping or any other damage. Do not disassemble charger. Call Snap-on/Sun Representative for repairs. • Use only recommended attachments. • Do not charge a frozen battery. Do not overcharge a battery.
  • Page 4 Safety Information Refer to Figure 1. Use the charger on a nominal 120 VAC circuit that has a grounding outlet that looks like B. An adaptor can be used, such as one like E to connect the plug to a two- pole outlet like C, until a properly grounded outlet can be installed by a qualified electrician.
  • Page 5: Charging Instructions

    Safety Information Charging Instructions Follow the information in this section to help ensure safety when connecting the charger cables to battery. For additional information refer to Battery Charging Procedure . Battery in Vehicle Use this information when charging battery in vehicle. •...
  • Page 6 Safety Information Disconnecting Charger • Turn Length of Charge Timer to OFF, • Disconnect power cord, • Remove clamp from ground, and • Remove clamp from battery terminal. Battery Not in Vehicle Follow this procedure when charging battery out of vehicle. •...
  • Page 7: Functional Description

    EEBC302A Operating Instructions Use this section for information about using the EEBC302A PRO CHARGER 250 Portable Battery Charger correctly and safely. The following are included: • Functional Description, • Battery Charging, • Maintenance, • Cranking Assist, • Assembly, and • Parts List. Functional Description The EEBC302A PRO CHARGER 250 Portable Battery Charger is a general-purpose 12-volt charger for automobile batteries...
  • Page 8 Operating Instructions EEBC302A A—Charging Mode Switch Two-position rocker amperage charging rate mode switch selects continuous charging of 35 amps in low position or 70 amps in high position and UL Cranking Assist output of 250 amps DC. B—Length of Charge Timer Selects charger power mode and charge duration with manual or automatic shut-off functions.
  • Page 9: Battery Charging Procedure

    EEBC302A Operating Instructions Battery Charging Procedure 1. Perform visual inspection of battery(ies) before charging to help prevent personal injury and property damage. Check the following conditions, correcting defects and/or replacing battery(ies) and components as required. — Cracked case. — Improper electrolyte level - fill to level specified by battery manufacturer.
  • Page 10: Operating Instructions

    Operating Instructions EEBC302A 6. Set Length of Charge Timer to HOLD. 7. Observe DC AMPS. Some reading should be evident. — If OK, allow to stabilize for 5 minutes. Recheck DC AMPS reading. — If not, set Length of Charge Timer to OFF. Determine reason for no reading.
  • Page 11 EEBC302A Operating Instructions Example: A battery is determined to be medium capacity since its CCA rating is 405 and Reserve Capacity is 90 minutes. Open circuit voltage test shows 12.1 volts, indicating about a 50% charge. Five minutes after the charger is powered up, charging current is 20 amps.
  • Page 12: Assembly Instructions

    Operating Instructions EEBC302A Cranking Assist Use this procedure to help the battery crank the engine over in a vehicle with a discharged battery. • Use only on batteries in good condition. • Do not use if the battery has been discharged for a long period of time, since it may be sulfated.
  • Page 13: Maintenance

    EEBC302A Operating Instructions 1. Attach handle to charger with four screws provided. 2. Attach crossbar to handle with two screws provided. 3. Attach foot to base with two hex head screws provided. 4. Slide wheel onto axle with hub toward charger, then slide axle through charger base.
  • Page 14: Wiring Diagram

    Operating Instructions EEBC302A Wiring Diagram Figure 4: Wiring Diagram, EEBC302A PRO CHARGER 250 B – Black C – White E – Red F – Green G – Blue SAVE THESE INSTRUCTIONS...
  • Page 15 APPLY, AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED. The obligations of Snap-on under this warranty are limited solely to the repair or, at the option of Snap-on, replacement of or refund of the original purchase price for, Battery Charger or parts which to the satisfaction of Snap-on are determined to be defective and which are necessary, in the judgment of Snap-on, to return the Battery Charger to good operating condition.
  • Page 16 Operating Instructions EEBC302A ©1999 Snap-on Incorporated ZEEBC302A Printed in U.S.A. – (6/99)

This manual is also suitable for:

Bc5500bBc4200b

Table of Contents

Save PDF