Related Manuals for GE Security PTZ 12X
Summary of Contents for GE Security PTZ 12X
- Page 1 Security TruVision Mini PTZ 12X Camera Pocket Guide P/N 1069516 • REV A • ISS 01DEC09...
- Page 2 Copyright © 2009 GE Security, Inc.
-
Page 3: Table Of Contents
Setting the communication DIP switches 10 Setting the dome camera site ID 11 22-pin connector description 12 Wiring the dome camera 13 Main menu overview 15 Using a keypad to program menus 17 TruVision Mini PTZ 12X Camera Pocket Guide... -
Page 4: Introduction
I/O interface cable for power, video, alarms, and serial data TruVision Mini PTZ 12X Camera pocket guide TruVision Mini PTZ 12X Camera user manual (on CD) Installation environment When installing your camera, consider these factors: • Handling: Handle the camera carefully. Avoid striking, shaking, etc. - Page 5 Servicing: Do not attempt to service this unit yourself. Any attempt to dismantle or remove the covers from this product will invalidate the warranty and may also result in serious injury. Refer all servicing to qualified service personnel. TruVision Mini PTZ 12X Camera Pocket Guide...
-
Page 6: Example Of A System Setup
1. Main monitor 2. Spot monitor 3. Control keypad Cable requirements Table 1 lists the requirements for the cables that connect to the dome camera. 4. DVR /Multiplxer/ Quad/ Switcher 5. Camera 6. Repeater TruVision Mini PTZ 12X Camera Pocket Guide... - Page 7 75 ohm coaxial cable with BNC ends Alarm Cat-5 cable recommended. Power 24 VAC cable. To determine the size of cable needed for individual applications, please refer to the user manual. TruVision Mini PTZ 12X Camera Pocket Guide Max. length 1219 m (4000 ft) 486 m...
-
Page 8: Removing The Protective Cover From The Outdoor Camera
For detailed instructions, please refer to the user manual. Unpack the camera. Detach the outdoor top mount bracket counterclockwise and detach it from the main camera housing. Remove the protective cover and PE sheet from the camera. TruVision Mini PTZ 12X Camera Pocket Guide... - Page 9 DO NOT press on the top of the bubble. Screw the bubble and camera body together with the supplied M3 standard/security screw. TruVision Mini PTZ 12X Camera Pocket Guide...
-
Page 10: Setting Up The Camera
Set the DIP switches. Setting up the camera To quickly put the Mini PTZ 12X camera into operation Configure the camera’s DIP switches, which are located on the top of the camera. Set the camera communication protocol. -
Page 11: Camera Dip Switches
The dome camera can use different protocols for communication. To select a protocol, you must set the protocol DIP switches to the correct sequence of 1s (on) and 0s (off). TruVision Mini PTZ 12X Camera Pocket Guide Outdoor camera D. 22-pin connector E. -
Page 12: Setting The Communication Dip Switches
The RS-485 default setting is half-duplex (see Figure 2 below.) For further information on the other options available, please refer to the user manual. Figure 2: Default setting of RS-485 communication switch (half-duplex) Switch position TruVision Mini PTZ 12X Camera Pocket Guide... -
Page 13: Setting The Dome Camera Site Id
ID number for that dome camera. See Figure 3 above for an example. Place the switches that correspond to those values in the On position. Carefully record the site ID of each dome camera installed. TruVision Mini PTZ 12X Camera Pocket Guide... -
Page 14: 22-Pin Connector Description
ISOG Description Alarm Contact 1 Alarm Contact 2 Alarm Contact 3 Alarm Contact 4 Alarm Contact 5 Alarm Contact 6 Alarm Contact 7 Alarm Contact 8 Alarm Contact GND Video GND Video POS TruVision Mini PTZ 12X Camera Pocket Guide... -
Page 15: Wiring The Dome Camera
Wiring the dome camera The TruVision Mini PTZ 12X Camera is shipped with a 24 VAC I/O interface cable (see Figure 4). This cable facilitates installation as there is only one cable to connect to the dome camera. Figure 4: 24 VAC I/O interface cable 1. - Page 16 Connect the power cable to the power source. As soon as the dome camera is connected, it is operational. Note: The ground wire must be inserted into the center pin of the power input terminal block. See Figure 6 on page 15. TruVision Mini PTZ 12X Camera Pocket Guide...
-
Page 17: Main Menu Overview
The OSD menu can be pre-programmed to time-out after certain number of minutes of inactivity. All configuration changes made are automatically saved. Please refer to the user manual for detailed information on programming the dome camera and on-screen displays. TruVision Mini PTZ 12X Camera Pocket Guide... - Page 18 Figure 7: Main menu screens TruVision Mini PTZ 12X Camera Pocket Guide...
-
Page 19: Using A Keypad To Program Menus
1. The Main Page 1 menu appears. Navigating the menus You can use the keypad keys and joystick to navigate through the menu system. See the user manual for further information on their use. TruVision Mini PTZ 12X Camera Pocket Guide... -
Page 20: Key Function
Iris +: Enters or selects a menu option Iris -: Esc. Exits a menu option. There is no need to select the menu option Exit to quit a menu. TruVision Mini PTZ 12X Camera Pocket Guide... - Page 21 Figure 8: Joystick motion Previous TruVision Mini PTZ 12X Camera Pocket Guide Scroll up Scroll down Next Edit (turn joystick clockwise)