Advertisement
7.With a firm grip on the Die Grinder, lightly apply the Grinding drum to the workpiece,
slowly and steadily moving the grinding drum to the right and left until you have achieved
the desired appearance (finish) on the workpiece.
8.Once the work is completed, release hand pressure on the trigger, the safety will
automatically return to its locked position to prevent the trigger from accidentally being
activated.
9.Turn off the air compressor. Trip the safety with your finger, and slowly squeeze the
trigger to release any remaining air pressure from the die grinder. Then disconnect the air
hose from the tool.
10.Remove the grinding drum from the Die Grinder. Then store the tool in a clean, dry
location out of reach of children and untrained operators.
INSPECTION, MAINTENANCE AND CLEANING
1.Always make sure the trigger is in its "OFF" position, and disconnect the Die Grinder
from its compressed air supply before performing any inspection, adjustments,
maintenance, or cleaning.
2.Before each use, inspect the general condition of the Die Grinder. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, damaged air
hose, and any other condition that may affect its safe operation. If abnormal noise or
vibration occurs, have the problem corrected before further use. Do not use damaged
equipment.
3.Daily: With a clean cloth, remove all dirt, oil, and grease from the Die Grinder. If
necessary, you may use a mild detergent. Do not use solvents, as damaged to the Die
Grinder may occur. Do not immerse the Die Grinder in any liquids.
PARTS LIST
Description
Part#
Qty.
1
Air Inlet
1
2
Muffle Cover
1
3
Housing
1
4
Valve Plug
1
5
O-ring
1
O-ring
6
1
Air Regulator
7
1
Spring
8
1
O-ring
9
1
10
Valve Stem
1
O-ring
11
1
12
Steel Ball
1
Valve Busing
13
1
14
Pin
1
15
Trigger
1
Description
Part#
Bearing
16
17
End Plate
18
Pin
19
Rotor Blade
20
Rotor
Cylinder
21
22
Front Plate
Bearing
23
24
Washer
25
Collet Holder
26
Retainer
Housing Cap
27
28
Collet
29
Cap
30
Wrench
4 of 6
For technical questions and replacement parts, please call 1-800-222-5381.
Thank you very much for choosing a Wel-Bilt , Product! For future reference, please
complete the owner's record below:
Model: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire
manual to become familiar with this product before using it.
This machine is designed for certain applications only. The distributor strongly
recommends that this machine is not modified and/or used for any application other than
that for which it was designed. If you have any questions relative to a particular
application, DO NOT use the machine until you have first contacted Northern Tool +
Equipment to determine if it can or should be performed on the product.
Before using this product, please read the following instructions carefully.
TECHNICAL SPECIFICATIONS
Item
Collet Capacity
Rated Speed
Max. Air Pressure
Air Consumption
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep
Qty.
this manual and invoice in a safe and dry place for future reference.
1
1
GENERAL SAFETY RULES
2
Read and understand all instructions.
4
Failure to follow all instructions listed in the following pages may result in electric shock,
1
fire, and/or serious injury.
1
WORK AREA
1
1.Keep your work area clean and well lit. Cluttered benches and dark areas invite
1
accidents.
1
2.Do not operate pneumatic tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Pneumatic tools create sparks which
1
may ignite flammables.
1
3.Keep bystanders, children and pets away while operating a pneumatic tool.
1
Distractions can cause you to lose control. Protect others in the work area from debris
1
such as metal filings and sparks. Provide barriers or shields as needed.
1
2
TM
Purchase Date: _______________
Description
Item
1/4in.
Air Inlet Diameter
22,000 RPM
Min. Hose Size
90 PSI Recommended
Accessories
5 CFM
1 of 6
Description
1/4in.- 18NPT
3/8in.
Collet nut wrenches (2 pcs.)
Advertisement
