Advertising

TM
APX
TWO-WAY RADIOS
APX 6000 /
APX 6000Li
MODEL 3
USER GUIDE

   Also See for Motorola APX 6000

   Summary of Contents for Motorola APX 6000

  • Page 1

    TWO-WAY RADIOS APX 6000 / APX 6000Li MODEL 3 USER GUIDE...

  • Page 3

    PMLN5717D MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011–2012 by Motorola Solutions, Inc. All Rights Reserved. 10/12 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A.

  • Page 4

    Sending an Emergency Call On = Secure operation. Blinks when the battery is low. Off = Clear operation. Press the Emergency button. Blinking = Receiving an encrypted The more stripes, the stronger the voice call. signal strength for the current site Press and hold the PTT button.

  • Page 5: Declaration Of Conformity

    Address: 1303, East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product: Model Name: APX 6000/APX 6000Li conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules.

  • Page 6

    Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 7: Table Of Contents

    Documentation Copyrights ....xiv Contents Disclaimer ......xiv This User Guide contains all the information you need to use the APX™...

  • Page 8: Table Of Contents

    Adjusting the Volume ......9 TMS Menu Options ......25 Call Type Icons .

  • Page 9: Table Of Contents

    Making an Enhanced Private Call Selection ....... . 51 (Trunking Only) ......43 Saving a Channel in the Dynamic Zone from Channel Name .

  • Page 10: Table Of Contents

    Call Alert Paging ......64 Automatic Registration Service (ARS) ..76 Receiving a Call Alert Page .

  • Page 11: Table Of Contents

    Deleting a Text Message ....89 Unlocking Your Radio ..... 101 Deleting All Text Messages .

  • Page 12: Table Of Contents

    Viewing the Current Site ....113 Selecting an Enhanced Zone Bank ... .123 Changing the Current Site .

  • Page 13: Table Of Contents

    Voice Announcement ..... .134 Commercial Warranty ....150 Helpful Tips .

  • Page 14: Important Safety Information

    Before using this product, read the guide enclosed with your radio which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website: http://www.motorolasolutions.com/APX English...

  • Page 15: Software Version

    Check with your dealer or system administrator for more details of all the features supported. Changes or modifications made to this device, not expressly approved by Motorola, could void the user's authority to operate this equipment. English...

  • Page 16

    Pour obtenir une liste d'antennes et d'autres accessoires Informations importantes sur la approuvés par Motorola, consultez le site Web : sécurité http://www.motorolasolutions.com/APX Selon la règlementation d'Industrie Canada, cet émetteur radio GUIDE SUR L’EXPOSITION AUX ne peut être utilisé qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvés par Industrie Canada...

  • Page 17: Computer Software Copyrights

    Version du logiciel Computer Software Copyrights Toutes les fonctionnalités décrites dans les sections The Motorola products described in this manual may suivantes sont prises en charge par la version du logiciel include copyrighted Motorola computer programs stored R09.00.00 ou ultérieure de la radio.

  • Page 18

    However, no written permission of Motorola. No part of this manual responsibility is assumed for inaccuracies. Furthermore, may be reproduced, distributed, or transmitted in any...

  • Page 19: Getting Started, How To Use This Guide, Notations Used In This Manual

    Notations Used in This Manual Getting Started Throughout the text in this publication, you will notice the use of Take a moment to review the following: WARNING, Caution, and Note. These notations are used to How to Use This Guide ......page 1 emphasize that safety hazards exist, and the care that must be Notations Used in This Manual .

  • Page 20: Additional Performance Enhancement, Dynamic System Resilience (dsr), Crosstalk Prevention, Encrypted Integrated Data (eid), Securenet

    SecureNet enhance the security, quality and efficiency of the radios. SecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. Dynamic System Resilience (DSR) The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel.

  • Page 21: Can Tell You, Preparing Your Radio For Use

    What Your Dealer/System Administrator Preparing Your Radio for Use Can Tell You Assemble your radio by following these steps: Check with your dealer or system administrator for the correct Charging the Battery ......page 4 radio settings, if the radio is to be operated in extreme Battery Charger .

  • Page 22: Charging The Battery, Battery Charger, Attaching The Battery

    The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of Motorola-authorized batteries available for use with your radio, see Accessories on page 141. Note: When charging a battery attached to a radio, turn the radio off to ensure a full charge.

  • Page 23: Attaching The Antenna

    Attaching the Antenna To remove the battery, turn the radio off. Squeeze With the radio turned off, set the antenna in its receptacle and the release latches at the turn clockwise to attach it to the radio. bottom of the battery until the battery releases from the radio.

  • Page 24: Attaching The Accessory Connector Cover, Using The Carry Holder

    Attaching the Accessory Connector Using the Carry Holder Cover Position the radio within the carry holder with the The accessory connector is located on the antenna side of the main speaker facing radio. It is used to connect accessories to the radio. outward.

  • Page 25: Turning On The Radio

    To remove the radio from the Turning On the Radio carry holder, place the tip of your fingers on the ledge of Rotate the On/Off/Volume Control Knob clockwise until you the carry holder and push at hear a click. the bottom of the radio until the radio is released from it.

  • Page 26

    If the power-up test is unsuccessful, you see Error Note: XX/YY (XX/YY is an alphanumeric code). Turn off the radio, check the battery, and turn the radio back on. If the radio fails the power-up test again, record the Error XX/YY code and contact your dealer.

  • Page 27: Adjusting The Volume, Identifying Radio Controls

    Adjusting the Volume Identifying Radio Controls To increase the volume, turn the On/Off/Volume Control Knob Take a moment to review the following: clockwise. Radio Parts and Controls ..... . . page 10 Programmable Features .

  • Page 28: Radio Parts And Controls

    Radio Parts and Controls Antenna 16-Position Select Knob* On/Off/Volume Control Knob 3-Position A/B/C Switch* Top (Orange) Button* 2-Position Concentric Display Switch* Microphone Microphone Main Display Menu Select Top Side (Select) Buttons Button* Accessory Main Connector Speaker Push-to-Talk Data Feature (PTT) Button Bluetooth Button Pairing...

  • Page 29: Programmable Features, Assignable Radio Functions

    Bluetooth Data Devices – Keys up the Bluetooth data devices. Programmable Features Bluetooth Clear All Pairing – Allows you to clear all pairing Any reference in this manual to a control that is info for Bluetooth. This is accessed by a long press of the “preprogrammed”...

  • Page 30

    Man Down Clear – Clears the alarm of Man Down mode which Private Line Defeat (Conventional Only) – Overrides any was triggered when your radio achieves or passes a tilt angle coded squelch (DPL or PL) that is preprogrammed to a channel. threshold or a combination of the angle threshold and a motion Query –...

  • Page 31: Assignable Settings Or Utility Functions

    Site Display/Search (Trunking Only) – Displays the current Assignable Settings or Utility Functions site ID and RSSI value; performs site search for AMSS Light/Flip – Press the button to toggle the display backlight on (Automatic Multiple Site Select) or SmartZone operation. or off;...

  • Page 32: Accessing The Preprogrammed Functions, Using The Menu Select Buttons, Using The Navigation Buttons, Home Button

    Accessing the Preprogrammed Functions Using the Navigation Buttons Home Button You can access various radio functions through one of the following ways: button returns you to the Home (default) screen. In most • A short or long press of the relevant programmable buttons. cases, this is the current mode.

  • Page 33: Using The Keypad, Keypad Characters – Uppercase Mode

    Using the Keypad You can use the 3 x 4 alphanumeric keypad to access your radio’s features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet.

  • Page 34: Keypad Characters – Lowercase Mode

    Keypad Characters – Lowercase Mode Number of Times Key is Pressed & “ ‘ Toggle between mixed case mode, uppercase mode, and lowercase mode. Space Toggle between numeric and letter mode. English...

  • Page 35: Keypad Characters – Numeric Mode

    Keypad Characters – Numeric Mode Number of Times Key is Pressed & “ ‘ Space Toggle between numeric and letter mode. English...

  • Page 36: Keypad Characters – Hexadecimal Mode

    Keypad Characters – Hexadecimal Mode Number of Times Key is Pressed Not applicable Not applicable English...

  • Page 37: Push-to-talk (ptt) Button, Identifying Status Indicators

    Push-To-Talk (PTT) Button Identifying Status Indicators The PTT button on the side Your radio indicates its operational status through the following: of the radio serves two basic Status Icons ....... . . page 20 purposes: Text Messaging Service (TMS) Icons.

  • Page 38: Status Icons

    Status Icons Battery For IMPRES battery operation only – the icon The 130 x 130 pixel front liquid crystal display (LCD) of your shown indicates the charge remaining in the Top Display radio shows radio status, text entries, and menu entries. The battery.

  • Page 39

    In-Call User Alert Priority Channel Scan • • On = The feature is enabled. Voice muting of Blinking dot = Radio detects activity on the affiliated trunking talkgroup or channel designated as Top Display selected conventional channel is Priority-One. activated. •...

  • Page 40

    Basic Zone Bank 2 AES Secure Operation Top Display • • D = Radio is in Zone 4. On = AES Secure operation. • • E = Radio is in Zone 5. Off = Clear operation. • • F = Radio is in Zone 6. Blinking = Receiving an encrypted voice call.

  • Page 41

    Data Activity Lowercase Predictive Data activity is present. Indicates that the text entry is currently in lowercase and with predicted words shown at the bottom of the screen. Hexadecimal Mixedcase Predictive Indicates that the text entry is currently in Indicates that the text entry is currently in mixed hexadecimal mode.

  • Page 42: Text Messaging Service (tms) Icons, Status Icons

    Text Messaging Service (TMS) Icons Read Message The selected text message in the Inbox has been This feature allows you to send and receive text messages. See read. Text Messaging Service (TMS) on page 79 for more Normal Message information. User is composing a message with normal priority and without a request for a reply.

  • Page 43: Tms Menu Options, Call Type Icons

    Call Type Icons Priority Status and Request Reply • User is composing a message with a priority The following icons appear on the radio’s main display, when status and a request for a reply. you make or receive a call, or view selected call lists, to indicate •...

  • Page 44: Led Indicator

    LED Indicator Incoming call or data. The LED indicator shows the operational status of your radio. Outgoing call or data. LED Indicator Incoming emergency call. English...

  • Page 45

    Solid red – Radio is transmitting. Blinking green – Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Blinking red – Radio is transmitting at low battery condition. Programming mode. Rapidly blinking red –...

  • Page 46: Intelligent Lighting Indicators

    Intelligent Lighting Indicators This feature temporary changes the backlight of the top display screen, and adds a color bar to the main display screen to help signal that a radio event has occurred. Note: This feature must be preprogrammed by a qualified radio technician. Backlight and Bar Color Notification When...

  • Page 47: Alert Tones

    Alert Tones Your radio uses alert tones to inform you of your radio’s condition. The following table lists these tones and when they occur. You Hear Tone Name Heard Radio Self Test Fail When radio fails its power-up self test. Reject When an unauthorized request is made.

  • Page 48

    You Hear Tone Name Heard Valid Key-Press When a correct key is pressed. Radio Self Test Pass When radio passes its power-up self test. Clear Voice At beginning of a non-coded communication. Short, Priority Channel Medium-Pitched When activity on a priority channel is received. Received Tone Emergency Alarm /Call...

  • Page 49

    You Hear Tone Name Heard Short, High-Pitched Low-Battery Chirp When battery is below preset threshold value. Tone (Chirp) Fast Ringing When system is searching for target of Private Call. Ringing Enhanced Call Sent When waiting for target of Private Call to answer the call. Phone Call Received When a land-to-mobile phone call is received.

  • Page 50

    You Hear Tone Name Heard Sol-Doh Enhanced Zone Bank Dow When EZB Down button is pressed to scroll the Enhance Zone Bank down. English...

  • Page 51: Phone Call Display And Alert Prompts

    Phone Call Display and Alert Prompts The following appears on the radio’s display when you make and receive Phone calls. The radio also uses alert tones to indicate the current status. You Hear You See When Notes You press the PTT button and the No phone Press to hang up.

  • Page 52: General Radio Operation, Selecting A Zone

    Selecting a Zone General Radio Operation A zone is a group of channels. Once you understand how your APX 6000/APX 6000Li Portable is configured, you are ready to use your radio. 3-Position A/B/C Switch Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Zone .

  • Page 53: Selecting A Radio Channel

    Selecting a Radio Channel Follow the procedure below. < > A channel is a group of radio characteristics, such as transmit/ to Zone. receive frequency pairs. Press the Menu Select button directly below Zone. to the required zone. Use the keypad to enter the zone number. If the zone number entered is unprogrammed, the display shows Invalid entry.

  • Page 54

    Procedure: Turn the preprogrammed 16-Position Select Knob to the Follow the procedure below. desired channel. < > to ChUp or ChDn. Follow the procedure below. Press the Menu Select button directly below ChUpor ChDn. < > to Chan. Press the PTT button to transmit on the displayed zone and channel.

  • Page 55: Using Channel Search Button

    Press the Menu Select button directly below CSrh once the Using Channel Search Button entry is done to initiate searching. This feature allows you to do a quick search for a specific Press the Menu Select button directly below Cncl to exit. channel in your radio by keying in the alias of the channel.

  • Page 56: Using Mode Select Feature, Saving A Zone And Channel To A Softkey

    Using Mode Select Feature Saving a Zone and Channel to a Softkey Five softkeys are available for you to save the frequent used Mode Select allows a long press to save your radio’s current zone and channel. zone and channel to a programmable button, keypad button or Procedure: a softkey;...

  • Page 57: Saving A Zone And Channel To A Keypad Button

    Receiving and Responding to a Radio Call Saving a Zone and Channel to a Keypad Button All the programmable buttons and keypad digit 0 to 9 buttons Once you have selected the required channel and/or zone, you allow you to save the frequent used zone and channel. can proceed to receive and respond to calls.

  • Page 58: Receiving And Responding To A Talkgroup Call

    Receiving and Responding to a Talkgroup Call Receiving and Responding to a Private Call (Trunking Only) To receive a call from a group of users, your radio must be configured as part of that talkgroup. A Private Call is a call from an individual radio to another individual radio.

  • Page 59

    During the call, the display shows the caller ID (number), if Receiving and Responding to a Telephone Call the caller’s name is not in the call list. (Trunking Only) Press and hold the PTT button to talk. Release the PTT This feature allows you to receive calls similar to standard button to listen.

  • Page 60: Making A Radio Call, Making A Talkgroup Call, Making A Private Call (trunking Only)

    Making a Radio Call ASTRO Conventional Only: The LED lights up solid red. The display shows the talkgroup alias or ID. You can select a zone, channel, subscriber ID, or talkgroup by using: Trunking Only: • The LED lights up solid red. The preprogrammed Zone switch •...

  • Page 61

    Procedure: to the required ID. Press the preprogrammed Quick Access (One-Touch) Enhanced Private Call button to dial the preprogrammed ID Use the keypad to enter the required ID. and proceed to Step 5. Press the PTT button to initiate the Private Call. The display shows Calling...

  • Page 62: Making A Telephone Call (trunking Only)

    If no acknowledgment is received, the display shows No to the required phone number. acknowledge. Use the keypad to enter the required phone number. If the target radio does not respond before the time out, the Press and release the PTT button to dial the phone number. display shows No answer.

  • Page 63: Repeater Or Direct Operation, Monitoring Features, Monitoring A Channel

    Repeater or Direct Operation Monitoring Features The REPEATER operation increases the radio’s range by Radio users who switch from analog to digital radios often connecting with other radios through a repeater. The transmit assume that the lack of static on a digital channel is an and receive frequencies are different.

  • Page 64: Conventional Mode Operation

    Conventional Mode Operation Press the preprogrammed Monitor button and proceed to ® Your radio may be preprogrammed to receive Private-Line Step 3. (PL) calls. Procedure: Follow the procedure below. Momentarily press the Monitor button to listen for activity. The Carrier Squelch indicator appears on the display. Select the desired zone and channel.

  • Page 65: Advanced Features, Advanced Call Features, Receiving A Selective Call

    Advanced Call Features Advanced Features Use this navigation guide to learn more about advanced Receiving and Making a Selective Call (ASTRO features available with your radio: Conventional Only) Advanced Call Features ..... . . page 47 This feature allows you to receive a call from or to call a specific Contacts .

  • Page 66: Making A Selective Call, Selecting A Talkgroup

    Release the PTT button to listen. Making a Selective Call Press to return to the Home screen. Procedure: Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and Using the Talkgroup Call Feature (Conventional proceed to Step 4. Operation Only) This feature allows you to define a group of conventional Follow the procedure below.

  • Page 67: Sending A Status Call

    Press the Menu Select button directly below Sel to save the Follow the procedure below. currently selected talkgroup and return to the Home screen. < > If the encryption key associated to the new talkgroup is to Sts. erased, you hear a momentary key fail tone and the display Press the Menu Select button directly below Sts.

  • Page 68: Requesting A Reprogram (trunking Only)

    Using the Dynamic Regrouping Feature (Trunking Requesting a Reprogram (Trunking Only) Only) This feature allows you to notify the dispatcher when you want a This feature allows the dispatcher to temporarily reassign new dynamic regrouping assignment. selected radios to a particular channel where they can Procedure: communicate with each other.

  • Page 69: Classifying Regrouped Radios, Using Dynamic Zone Programming (dzp), Channel, Selection

    Classifying Regrouped Radios Entering the Dynamic Zone to Select a Dynamic Channel The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. Procedure: < > to Zone. • Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the Press the Menu Select button directly below Zone.

  • Page 70: Name

    any unwanted characters. to the required zone. Press the Menu Select button directly below Sel. The display shows Select Chan screen. Press to add a space. Press to toggle between mixed case mode, uppercase to the required channel. Press the Menu Select mode, and lowercase mode.

  • Page 71: Deleting A Channel In The Dynamic Zone, Contacts

    Contacts Deleting a Channel in the Dynamic Zone With the radio in Dynamic Zone, follow the procedure below. This feature provides “address-book” capabilities on your radio. Procedure: Each entry corresponds to an alias (name) or ID (number) that < > you use to initiate a call.

  • Page 72: Making A Private Call From Contacts

    Your radio also supports a maximum of 50 call lists. Each list to select the call type. can store up to 100 IDs (numbers). Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from Note: Your radio is preprogrammed with a number of your mouth.

  • Page 73: Adding A New Contact Entry

    The display shows Edit name and a blinking cursor Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. appears. Use the keypad to enter the name. Press the PTT button to initiate the call. During the call, the <...

  • Page 74: Deleting A Contact Entry

    Press the Menu Select button directly below Del to delete Deleting a Contact Entry any unwanted characters. Procedure: Press the Menu Select button directly below Ok once you < > to Cnts. have entered the number. Press the Menu Select button directly below Cnts. The Press the Menu Select button directly below Cncl to return entries are alphabetically sorted.

  • Page 75: Adding A Contact To A Call List, Removing A Contact From A Call List

    Adding a Contact to a Call List Removing a Contact from a Call List Procedure: Procedure: < > < > to Cnts. to Cnts. Press the Menu Select button directly below Cnts. The Press the Menu Select button directly below Cnts. The entries are alphabetically sorted.

  • Page 76: Editing A Contact In A Call List, Editing An Entry Alias, Editing As Entry Id

    Press the Menu Select button directly below Ok once you Editing a Contact in a Call List have finished. The display returns to the Edit Contact screen. Editing an Entry Alias Press the Menu Select button directly below Done to save Procedure: your changes and return to the main screen for Contacts.

  • Page 77: Editing A Call Type, Viewing Details Of A Contact

    Press the Menu Select button directly below Done to save Press to toggle between mixed case mode, uppercase mode, and lowercase mode. your changes and return to the main screen for Contacts. Press to toggle between numeric and letter mode. Viewing Details of a Contact Press the Menu Select button directly below Ok once you have finished.

  • Page 78: Scan Lists, Viewing A Scan List, Editing The Scan List

    Scan Lists Editing the Scan List This feature lets you change scan list members and priorities. Scan lists are created and assigned to individual channels/ Procedure: groups. Your radio scans for voice activity by cycling through the Long press the preprogrammed Scan List Programming channel/group sequence specified in the scan list for the current button (side button) and proceed to Step 3.

  • Page 79: Changing The Scan List Status

    to select more channels to be added or deleted. Changing the Scan List Status Procedure: Use the keypad to go directly to additional channels to be added or deleted. Long press the preprogrammed Scan List Programming button (side button). Use the 16-Position Select knob to select additional channels to be added or deleted.

  • Page 80: Viewing And Changing The Priority Status, Scan, Turning Scan On Or Off

    Scan Viewing and Changing the Priority Status Procedure: This feature allows you to monitor traffic on different channels Below the Sel, Del, and Rcl screen, press the Menu Select by scanning a preprogrammed list of channels. button directly below Sel to view and/or change the priority status of the currently displayed channel.

  • Page 81: Deleting A Nuisance Channel

    Making a Dynamic Priority Change (Conventional < > to Nuis. Press the Menu Select button directly below Scan Only) Nuis. While the radio is scanning, the dynamic priority change feature The radio continues scanning the remaining channels in the allows you to temporarily change any channel in a scan list list.

  • Page 82: Call Alert Paging, Receiving A Call Alert, Sending A Call Alert

    Call Alert Paging Sending a Call Alert Page Note: The radio automatically exits the feature, if the feature This feature allows your radio to work like a pager. inactivity timer is enabled, when the radio is left idle Even if other users are away from their radios, or if they are and the timer expires.

  • Page 83

    If the call alert page is not acknowledged, you hear a low If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge. tone and the display shows No acknowledge. The radio returns to the Home screen. The radio returns to the Home screen.

  • Page 84: Emergency Operation

    Note: The radio operates in the normal dispatch manner Emergency Operation while in Emergency Call, except if enabled, it returns to one of the following: The Emergency feature is used to indicate a critical situation. • Tactical/Non-Revert – The radio sends emergency If the Top (Orange) button is preprogrammed to send an alarm and/or make emergency call on the current emergency signal, this signal overrides any other...

  • Page 85: Sending An Emergency Alarm, Sending An Emergency Call (trunking Only)

    Sending an Emergency Alarm Sending an Emergency Call (Trunking Only) This feature allows you to send a data transmission, which This feature gives your radio priority access to a talkgroup. identifies the radio sending the emergency, to the dispatcher. Procedure: Note: Emergency button press timer by default is set to 1 Press the preprogrammed Emergency button.

  • Page 86: Emergency Call, Sending A Silent Emergency Alarm

    Press and hold the PTT button. Speak clearly into the Sending an Emergency Alarm with Emergency microphone. Call Release the PTT button to end the transmission and wait for This feature gives your radio priority access on a channel for a response from the dispatcher.

  • Page 87: Changing Channels During Emergncy, Using The Emergency Keep-alive Feature, Fireground (conventional Only)

    Fireground (Conventional Only) Changing Channels during Emergncy For ALL Emergency transmissions, when changing channels: The portable Fireground Communications System is designed • If the new channel is also preprogrammed for Emergency, for deployment at an incident scene. It consists of five central you can change channels while in Emergency operation.

  • Page 88: Entering Fireground Zone Channel

    The Fireground signals transmission is always exchanging data Listen for a transmission. Adjust the Volume Control Knob if between your radio and the RF Modem and command terminal. necessary. The status of your radio includes Press and hold the preprogrammed Volume Set button to •...

  • Page 89: Responding To Evacuation Indicator, Tactical Public Safety(tps) (conventional Only), Using Tps Normal Transmission

    Tactical Public Safety(TPS) (Conventional Responding to Evacuation Indicator Only) When Incident Commander triggers Evacuation signal from his command terminal, the RF Modem updates everyone in the Fireground Communication System with the order to evacuate Using TPS Normal Transmission the incident site. TPS enabled the users of a group to identify a transmission Procedure: starts and ends clearly by displaying the caller’s name or ID on...

  • Page 90: Man Down

    Man Down Using TPS Emergency Transmission Emergency Beacon – During Emergency if the TPS radio user Man Down condition is determined based upon the radio tilt pushes the Emergency button, the radio sounds a Beacon at angle or a combination of radio tilt angle and the lack of radio the maximum volume of the radio at radio’s internal speaker motion.

  • Page 91: Pre-alert Timer

    The Man Down feature has three phases: Note: Emergency must be set up for this feature to operate. For details on operating the Emergency alerts, please The radio senses the Man Down condition and Pre-Alert see Emergency Operation on page 66. Timer is initiated.

  • Page 92: Post-alert Timer, Triggered, Triggering Emergency, Exiting Man Down Feature

    Post-Alert Timer Triggering Emergency This timer sets the amount of time the radio needs to remain in When the user does not clear the Man Down condition and the the Man Down condition before the Emergency alarm is Post-Alert Timer comes to an end, Emergency Alarm or call is transmitted.

  • Page 93: Re-initiating Man Down, Testing The Man Down Feature

    enabled, please enable it and go through steps 1,2 and 3 Re-Initiating Man Down again. After exiting the Emergency Operation when the radio is still in Man Down condition (tilted achieving threshold angle or If the Man Down feature is enabled and no tone is heard, motionless), user must first exit Man Down condition to then re- send the radio to a qualified technician.

  • Page 94: Automatic Registration Service (ars), Selecting Or Changing The Ars Mode

    Advanced Automatic Registration Service (ARS) Selecting or Changing the ARS Mode Procedure: This feature provides an automated data application registration Turn the preprogrammed 16-Position Select knob, once the for the radio. When you turn on the radio, the device zone you want is displayed, to the desired mode. automatically registers with the server.

  • Page 95: Accessing The User Login Feature, Logging In As A User

    < Press to move one space to the left. Accessing the User Login Feature > Press to move one space to the right. This feature allows you as the user to be associated with the Press the Menu Select button directly below Del to delete radio.

  • Page 96: Logging Out

    Indicator icon, the ID, and Logged in, with Logt and Exit. Logging Out When you have logged in or you are using Offline mode, you In non-ARS enabled mode, the display shows Offline, with Logt and Exit. can log out. Procedure: If the username is invalid, login fails and the user login failure indicator (IP indicator) icon blinks.

  • Page 97: Text Messaging Service (tms), Accessing The Messaging Features

    Text Messaging Service (TMS) Accessing the Messaging Features Note: The radio automatically exits the feature, if the feature This features allows you to quickly send and receive messages inactivity timer is enabled, when the radio is left idle and run database queries directly from your radios. and the timer expires.

  • Page 98: Composing And Sending A New Text Message

    Press the Menu Select button directly below Del to delete Composing and Sending a New Text Message any unwanted characters. Note: During the uppercase and lowercase mode, multi- Press to add a space. tapping the keys only scrolls through the letters. For Press to toggle between mixed case mode, uppercase example, A->B->C, a->b->c.

  • Page 99: Sending A Quick Text Message, Using The Priority Status And Request Reply

    Press the Menu Select button below Send or the PTT Sending a Quick Text Message button to send the message. Quick Text messages are messages that are predefined and The display shows the Send Message screen and usually consist of messages that are used most frequently. Sending msg.

  • Page 100

    The message appears on the Compose screen, with a Press to add a space. blinking cursor at the end of it. Press to toggle between mixed case mode, uppercase Use the keypad to edit the message, if required. mode, and lowercase mode. <...

  • Page 101: Features, Appending A Priority Status To A Text Message

    Using the Priority Status and Request Reply Removing a Priority Status from a Text Message Features Procedure: Before sending your message, you can append a priority status After the outgoing message is composed (see Composing and and/or a request reply to your message. Sending a New Text Message on page 80 for more information): Appending a Priority Status to a Text Message...

  • Page 102: Removing A Request Reply From A Text Message, Text Message, A Text Message

    to Req Reply and press the Menu Select button Removing a Request Reply from a Text Message directly below Sel to request for a reply. Procedure: The priority status and request reply icons appear beside After the outgoing message is composed (see Composing and the normal message icon on the label bar.

  • Page 103: Managing Text Messages, Receiving A Text Message, Viewing A Text Message From The Inbox

    Managing Text Messages Viewing a Text Message from the Inbox The Inbox can hold up to thirty (30) messages. Receiving a Text Message Note: to read the message if fills more than one Note: When you receive a message that is flagged with the screen.

  • Page 104: Replying To A Received Text Message

    While on the view message screen, press the Menu Select to scroll through the list of messages and press the Optn Back button directly below , or to access the option. Menu Select button directly below Sel to select the required message.

  • Page 105: Accessing The Drafts Folder, Managing Sent Text Messages, Viewing A Sent Text Message

    Back Note: You can append a priority status and/or a request reply • Select to return to the previous screen. to your message. See Using the Priority Status and Request Reply Features on page 83 for more Managing Sent Text Messages information.

  • Page 106: Sending A Sent Text Message

    The display shows a list of aliases or IDs, with the recipient Sending a Sent Text Message of latest sent message on top. Procedure: to the required aliases or ID and press the Menu Press the Menu Select button directly below Optn while Select button below Sel to view the message.

  • Page 107: Deleting A Text Message, Deleting All Text Messages

    The display shows the Send Message screen and Deleting All Text Messages Sending msg. Procedure: Back Press the Menu Select button directly below at any time to Press the preprogrammed Data Feature button or the TMS return to the previous screen. Feature button to access the Messaging feature screen, and proceed to Step 3.

  • Page 108: Astro 25 Advanced Messaging Solution, Solution

    System Setup for ASTRO Advanced Messaging quickly send and receive messages and run database queries Solution directly from your data-enabled Motorola two-way radios. Federal mandate requires Two-Factor Authentication when Your user name, unit ID and password all need to be querying Federal and State databases.

  • Page 109: Two-factor Authentication, Logging Into Two-factor Authentication

    Two-Factor Authentication Logging into Two-Factor Authentication Procedure: Two-Factor Authentication is an extension of existing ARS and TMS operation. This feature allows you to authenticate yourself Press the preprogrammed User Login button and proceed to Step 3. with a username, unit ID, password and passcode. The purpose of this feature is to allow the sender of a text Follow the procedure below.

  • Page 110

    the display shows momentary Invalid UnitID. Repeat Step Press and hold to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below Sel to select A blinking cursor appears. Enter your password. the predefined username.

  • Page 111: Logging Out Of Two-factor Authentication, Sending A Query

    Logging out of Two-Factor Authentication Sending a Query Procedure: This feature is available for radio users who have successfully logged in with the Two-Factor Authentication. Query is a special Press the Menu Select button directly below Logt. form of Quick Text marked with a flag that is replied or The display shows Clear private data?.

  • Page 112

    Press the Menu Select button directly below Exit to return to to {Other Recpnt} and press the Menu Select the Home screen. button below Edit. A blinking cursor appears on the Enter Address screen. to Query and press the Menu Select button directly Use the keypad to type the address entry.

  • Page 113: Receiving A Query, Secure Operations, Selecting Secure Transmissions

    Receiving a Query Unlike other forms of security, Motorola digital encryption You shall received the information you have requested in TMS provides signaling that makes it virtually impossible for others to format.

  • Page 114: Selecting Clear Transmissions, Managing Encryption, Loading An Encryption Key

    The display shows Keyloading, and all other radio Selecting Clear Transmissions functions, except for power down, backlight, and volume, Procedure: are locked out. Turn the preprogrammed Secure/Clear switch to the clear Select the required keys and press the Menu Select button position.

  • Page 115: Using The Multikey Feature, Selecting An Encryption Key

    Using the Multikey Feature Selecting an Encryption Key This feature allows the radio to be equipped with different Procedure: encryption keys and supports the DES-OFB algorithm. < > to Key. There are two types: Press the Menu Select button directly below Key. The •...

  • Page 116: Selecting A Keyset, Erasing The Selected Encryption Keys

    The radio exits keyset selection and returns to the Home Selecting a Keyset screen. This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the Erasing the Selected Encryption Keys radio.

  • Page 117

    directly below Yes to erase the displayed encryption key Requesting an Over-the-Air Rekey (ASTRO OR No to return to the previous screen. Conventional Only) Press , the PTT button, or the Menu Select button directly This feature, also known as OTAR, allows the dispatcher to below Exit to exit.

  • Page 118: Mdc Over-the-air Rekeying (otar), Infinite Ukek Retention, Hear Clear

    MDC Over-the-Air Rekeying (OTAR) Page Hear Clear This feature allows to view or define MDC Over-the-Air There are two components of Hear Clear. Rekeying (OTAR) features.It is applied only when operating in Companding: secure encrypted mode and only for conventional Reduces the channel noise, e.g.

  • Page 119: Security, Radio Lock, Unlocking Your Radio, Changing Your Password

    If the password is incorrect, the display show Incorrect Security password and the radio remains locked. If you enter three incorrect passwords in a row, the display Radio Lock Deadlock shows . Turn the radio off and then on, and begin This feature changes your radio to a more robust security again at Step 1.

  • Page 120: Changing Your Tactical Inhibit Password

    Press the Menu Select button directly below Ok. Changing Your Tactical Inhibit Password Enter the new password. Procedure: < > Press the Menu Select button directly below Sel. to Pswd. Re-enter the new password. Press the Menu Select button directly below Pswd. The display shows Change Password screen.

  • Page 121: The Global Positioning System (gps), Understanding The Gps Feature

    The Global Positioning System (GPS) Enabling or Disabling the Radio Lock Feature (Secure Radios Only) This feature uses information from the Global Positioning This feature allows you to enable or disable the radio lock System (GPS) satellites orbiting the Earth to determine the feature.

  • Page 122: Enhancing Gps Performance, The Outdoor Location Feature (using Gps)

    • Inside of buildings, trains, or other covered vehicles Enhancing GPS Performance • Under any other metal or concrete roof or structure Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message •...

  • Page 123: Enabling Mgrs Coordinates, Accessing The Outdoor Location Feature

    The radio also stores four (4) preprogrammed waypoints. These Accessing the Outdoor Location Feature coordinates cannot be deleted. Note: An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system Programmable Waypoints Preprogrammed Waypoints administrator.

  • Page 124: Saving A Waypoint

    While the new location is being determined, the location Saving a Waypoint signal can be a solid or blinking icon. Procedure: Once the location coordinates are fixed, the display shows While in the current location display: the current location along with the UTC (Zulu) time and date Press the Menu Select button directly below Optn.

  • Page 125: Viewing A Saved Waypoint

    Press the Menu Select button directly below Cncl to return Viewing a Saved Waypoint to the Location main screen. Procedure: Press the Menu Select button directly below Ok once you While in the current location display: are done. Press the Menu Select button directly below Optn. The display shows Current loc saved as <Waypoint to Waypoints and press the Menu Select button name>.

  • Page 126: Editing The Alias Of A Waypoint, Editing The Coordinates Of A Waypoint

    Press the Menu Select button directly below Ok once you Editing the Alias of a Waypoint are done. Procedure: While in the current location display: Press the Menu Select button directly below Cncl to return to the Waypoints main screen. Press the Menu Select button directly below Optn.

  • Page 127: Deleting A Single Saved Waypoint

    The display shows {Destination} Updated and the radio returns to the Waypoints main screen. to {Destination} and press the Menu Select button directly below Optn. to Edit Location and press the Menu Select button Deleting a Single Saved Waypoint directly below Sel. Procedure: While in the current location display: The first number blinks.

  • Page 128: Deleting All Saved Waypoints, Waypoint

    Deleting All Saved Waypoints Measuring the Distance and Bearing from a Saved Waypoint Procedure: While in the current location display: Procedure: While in the current location display: Press the Menu Select button directly below Optn. Press the Menu Select button directly below Optn. to Waypoints and press the Menu Select button directly below Sel.

  • Page 129: Mode, Trunking System Controls, Using The Failsoft System

    Trunking System Controls Using the Location Feature While in Emergency Mode When the Emergency feature is activated by pressing the Using the Failsoft System emergency button, the radio exits the Location menu and The failsoft system ensures continuous radio communications returns to the Home (default) screen so that you can see which during a trunked system failure.

  • Page 130: Going Out Of Range, Using The Site Trunking Feature, Locking And Unlocking A Site

    Going Out of Range Locking and Unlocking a Site When your radio goes out of the range of the system, it can no This feature allows your radio to lock onto a specific site and not longer lock onto a control channel. roam among wide-area talkgroup sites.

  • Page 131: Viewing The Current Site, Changing The Current Site, Bluetooth, Turning The Bluetooth On

    Viewing the Current Site Procedure: This feature allows your radio to extend its functionality by connecting to external proprietary Motorola Accessories. Press the preprogrammed Site Displ/Srch button. The default setting for Bluetooth-enabled radio is Bluetooth ON. The display shows momentary the name of the current site...

  • Page 132: Turning The Bluetooth Off, Re-pair Timer

    Press the Menu Select button directly below Exit to return You hear a short, medium-pitched tone. The display shows to the Home screen. momentary Bluetooth off, and disappears. Re-Pair Timer Press the preprogrammed button to turn on the Bluetooth. There are two options for configuring the radio’s Bluetooth You hear a short, medium-pitched tone.

  • Page 133: Bluetooth Drop Timer

    Bluetooth Drop Timer Re-Pair Timer The Bluetooth Drop Timer has two different settings and Re-Pair Timer Scenarios Options functions, depending upon the selection of the Re-Pair Timer. • When the radio is powered OFF, pairing Re-Pair Timer Description key is lost immediately, and accessory Options attempts to pair again.

  • Page 134: Pairing Bluetooth Device With The Radio

    Procedure: Pairing Bluetooth Device with the Radio Note: Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. With your radio’s Bluetooth feature ON, and the Bluetooth tones enabled: Bluetooth Turn on the accessory, then place it close to your radio...

  • Page 135: Indicating Bluetooth Connection Is Lost

    Turning On the Bluetooth Audio (Routing the If the connecting process immediately follows the pairing Audio from the Radio to the Headset) process and the connecting process fails to complete within Procedure: 6 seconds, you hear a decremental-pitched tone to indicate unpaired.

  • Page 136: Device, Information

    Turning Off the Bluetooth Audio (Routing the Adjusting the Volume of the Radio from Bluetooth Audio from the Headset to the Radio) Audio Device Procedure: Procedure: < > to BT. Press the Menu Select button directly below With the Bluetooth audio device connected to the radio: BT to access the Bluetooth feature screen.

  • Page 137

    Press the Menu Select button directly below Back to return Clearing All Bluetooth Devices Information to the previous screen. Procedure: to the required device, press the Menu Select Long press the preprogrammed Bluetooth On/Off button. You button directly below Clr. hear a short, medium-pitched tone.

  • Page 138: Editing The Bluetooth Friendly Name, Programming Over Project 25 (pop 25) (astro

    Programming Over Project 25 (POP 25) Editing the Bluetooth Friendly Name (ASTRO 25 and ASTRO Conventional) Note: Your radio must be preprogrammed to allow you to use this feature. This feature enables configuration data to be upgraded to your Procedure: radio over-the-air.

  • Page 139: Responding To The Notification Of Upgrade, Utilities, Viewing The Recent Calls

    Utilities Responding to the notification of Upgrade Procedure: Viewing the Recent Calls The display shows Upgrade?. This feature allows you to view the recent incoming and Press the Menu Select button below Acpt to accept the outgoing call information of the following call types: request to upgrade immediately.

  • Page 140: Using The Flip Display

    Press the Menu Select button directly below Rcnt to access Selecting a Basic Zone Bank the Recent Calls feature screen. This feature allows twice as many zones to be accessed from a to scroll through the list. switch, doubling the amount of switch positions. Press the Menu Select button directly below Exit to return to Note: The Basic Zone Select feature must to be...

  • Page 141: Selecting An Enhanced Zone Bank, Selecting The Power Level

    Selecting an Enhanced Zone Bank Selecting the Power Level This feature is created in order to allow users to communicate in This feature enables you to reduce the transmit power level for more zones. An Enhanced Zone Bank (EZB) consists of three specific case that require a lower power level.

  • Page 142: Selecting A Radio Profile, Enabling And Disabling The Radio Alias, Selecting The Audio Speaker

    The display shows Low power and the low power icon. Press the Menu Select button directly below Exit to exit the screen without making any changes. The display shows High power and the high power icon. The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile.

  • Page 143: Controlling The Display Backlight

    during typical radio operation, each speaker has an Controlling the Display Backlight independently-tuned frequency response and volume You can enable or disable the radio’s display backlight as level operation. needed, if poor light conditions make the display or keypad The secondary speaker also has a "whisper" mode with a difficult to read.

  • Page 144: Locking And Unlocking The Keypad And Controls, Turning Keypad Tones On Or Off

    Locking and Unlocking the Keypad and Controls Turning Keypad Tones On or Off You can lock your radio’s keypad, programmable buttons, rotary You can enable and disable keypad tones, if needed. knobs and switches to avoid inadvertent entry. Check with your Procedure: dealer or qualified technician for best selection to suite your Press the preprogrammed Keypad Mute button to turn the...

  • Page 145: Turning Voice Mute On Or Off, Using The Time-out Timer

    Turning Voice Mute On or Off Using the Time-Out Timer You can enable and disable voice transmission, if needed. This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting. Procedure: Press the preprogrammed Voice Mute button to turn the feature If you attempt to do so, the radio automatically stops your off or on.

  • Page 146: Setting The Time And Date, Editing The Time And Date

    Setting the Time and Date Press the Menu Select button directly below Exit to exit the You can set the time and date for your radio. screen without making any changes and return to the Home screen. Settings: Press the Menu Select button directly below Ok once you •...

  • Page 147: Analog Options, Features, Digital Options, Using The Pl Defeat Feature

    Using the Conventional Squelch Operation Option Result Features You hear any digital traffic having Selective Switch the correct network access code This feature filters out unwanted calls with low signal strength or and correct talkgroup. channels that have a higher than normal background noise. Using the PL Defeat Feature Analog Options This feature allows you to override any coded squelch (DPL or...

  • Page 148: Using The Digital Ptt Id Feature

    Three variations of smart PTT are available: Using the Digital PTT ID Feature Mode Description This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, Transmit Inhibit You cannot transmit if any traffic is consisting up to a maximum of eight characters, can be viewed on Busy Channel...

  • Page 149: Impres™ Battery Annunciator, Accessing The Battery Info Screen, Accessing The General Radio Information

    IMPRES™ Battery Annunciator Accessing the General Radio Information This feature displays the current capacity and charges cycles of Your radio contains information on the following: your battery when an IMPRES Battery is powering your radio. • Radio Information This feature must be enabled in your radio to see the information.

  • Page 150: Accessing The Radio Information

    Procedure: Accessing the Radio Information Press the preprogrammed Info button and proceed to Step 3. This feature displays the following information of your radio: Follow the procedure below. • • Host Version DSP Version < > to Info. • • Secure Version KG (Secure Algorithm) •...

  • Page 151: Viewing The Ip Information, Viewing The Control Assignments

    Viewing the IP Information Viewing the Control Assignments This feature displays the device name, IP address, and status of This feature displays the programmable radio functions your radio. assigned to the controls of your radio for the currently selected channel. Note: The device name of your radio is preprogrammed.

  • Page 152: Editing The Soft Id

    Press the Menu Select button directly below Del to delete Editing the Soft ID any unwanted characters. This feature allows you to change your username. Press to add a space. Press to toggle between mixed case mode, uppercase Note: Your radio must be preprogrammed to allow you to use mode, and lowercase mode.

  • Page 153

    The two options of priority for the Voice Announcement • Change to a new zone. The radio announces the current available are: zone and channel it is transmitting. • • Change to a new channel remaining within the current zone. High –...

  • Page 154: Helpful Tips, Caring For Your Radio

    • (For APX 6000/ APX 6000Li R Radios Only) Your radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours. Exceeding either maximum limit may result in damage to the radio.

  • Page 155: Cleaning Your Radio

    Cleaning Your Radio • (For APX 6000/APX 6000Li R Radios Only) Elastomer technology materials used for seals Procedure: in rugged portable radios can age with time and a u t i o n environmental exposure. Therefore, Motorola To clean the external surfaces of your radio:...

  • Page 156: Handling Your Radio, Servicing Your Radio

    • Avoid subjecting the radio to an excess of liquids. Do not communication equipment in perfect operating condition. A submerge the radio unless it is a ruggedized, APX 6000/APX nationwide service organization is provided by Motorola to 6000Li R model.

  • Page 157: Taking Care Of The Battery, Checking The Battery Charge Status, Led And Sounds

    Taking Care of the Battery Fuel Gauge Icon A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the Checking the Battery Charge Status battery with a fully charged one. Your radio can indicate the battery’s charge status through: Gauge Battery Charge...

  • Page 158: Battery Recycling And Disposal

    Battery Recycling and Disposal Gauge Battery Charge In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for battery collection and recycling. Many retailers and dealers 11% to 25%* Top Display participate in this program.

  • Page 159: Accessories, Highlights For The Accessories

    Highlights for the Accessories Accessories GPS only antenna is only used in either a single band UHF The accessory link below is for APX radios. Not all accessories or 700/800 application where the Public Safety Microphone are FCC certified to operate with all APX models and/or (PSM) is used with the corresponding PSM antenna.

  • Page 160: Frequency Range, Special Channel Assignments, Emergency Channel, Non-commercial Call Channel

    State the position of the vessel in distress, using any Appendix: Maritime Radio Use in the information that will help responders to locate you, e.g.: VHF Frequency Range • latitude and longitude • bearing (state whether you are using true or magnetic Take a moment to review the following: north) Special Channel Assignments.

  • Page 161: Operating Frequency Requirements

    Table A-1: VHF Marine Channel List (Continued) Operating Frequency Requirements Frequency (MHz) Channel A radio designated for shipboard use must comply with Federal Number Transmit Receive Communications Commission Rule Part 80 as follows: 156.150 160.750 • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 156.200 160.800...

  • Page 162

    Table A-1: VHF Marine Channel List (Continued) Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Frequency (MHz) Channel Channel Number Number Transmit Receive Transmit Receive 157.150 161.750 157.200 161.800 157.250 161.850 77** 156.875 – 157.300 161.900 156.925 161.525 157.350 161.950 156.975 161.575...

  • Page 163: Glossary

    Carrier Squelch squelch circuit silences the radio when no Automatic Registration Service signal is being received so that the user does not have to listen to “noise”. Motorola standard for wireless digital ASTRO 25 trunked communications. A software-controlled, computer-driven ASTRO...

  • Page 164

    Term Definition Term Definition Typically refers to radio-to-radio A feature that allows the dispatcher to Conventional communications, sometimes through a Dynamic temporarily reassign selected radios to a repeater (see Trunking). Regrouping single special channel so they can communicate with each other. Conventional A scan list that includes only conventional Scan List...

  • Page 165

    It can also trigger Emergency Alarm the and sites. Post-Alert Timer is not cancelled. NiMH Nickel-metal-hydride. Motorola Data Communication The user talks on a preprogrammed Non-Tactical/ A software-activated feature shown at the emergency channel. The emergency alarm Revert bottom of the display –...

  • Page 166

    Term Definition Term Definition Personality A set of unique features specific to a radio. A conventional radio feature, where you talk through a receive/transmit facility that Personal Identification Number Repeater re-transmits received signals, in order to A software application which streamlines improve communications range and critical real time operations and simplifies coverage.

  • Page 167

    Term Definition Term Definition The user talks on the channel that was Coordinated Universal Time. The Tactical/ selected before the radio entered the international time standard (formerly Non-Revert emergency state. Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, Bypass a repeater and talk directly to England, which is located at 0 degrees Talkaround...

  • Page 168: Commercial Warranty, Limited Warranty

    Commercial Warranty Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Limited Warranty Unless made in a separate agreement between MOTOROLA and...

  • Page 169

    . H)Freight costs to the repair depot. Warranty service will be provided by MOTOROLA through one of its I) A Product which, due to illegal or unauthorized alteration of the authorized warranty service s. If you first contact the company software/firmware in the Product, does not function in which sold you the Product (e.g., dealer or communication service...

  • Page 170

    VI. PATENT AND SOFTWARE PROVISIONS: MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or MOTOROLA will defend, at its own expense, any suit brought parts furnished hereunder with software, apparatus or devices not...

  • Page 171

    Motorola Solutions Australia’s limited warranty below is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: http://www.motorola.com/Business/XA-EN/...

  • Page 172

    Notes English...

  • Page 174

    Schaumburg, Illinois 60196 U.S.A. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2010–2012 Motorola Solutions, Inc. All rights reserved.

This manual also for:

Apx 6000li

Comments to this Manuals

Symbols: 0
Latest comments: