Related Manuals for Küppersbusch KD9980.0TGE
Summary of Contents for Küppersbusch KD9980.0TGE
- Page 1 BEDIENUNGS- UND MONTAGEANWEISUNG GB INSTRUCTIONS FOR ASSEMBLY AND USE GR ΟΓΗΓΙΔ ΥΔΙΡΙΜΟΤ ΚΑΙ ΤΝΑΡΜΟΛΟΓΗΗ KD9980.0TGE IKD9980.0TGE KD9980.0BGE IKD9980.0BGE...
-
Page 3: Table Of Contents
Contents General Contents Your appliance data Safety Instructions Installation Assembly instructions Electrical connection Other assembly instructions and tips Mounting on a wall Mounting on the ceiling Operation Switching your appliance on / off Power controls Automatic delayed stop Switching the lamp on / off Dimmer function Night Light function Filter saturation display... - Page 4 Please note: We require the following details for your request for customer service so that our customer service technicians can be well-prepared to carry out repairs and have the required spare parts available: Your exact address Your telephone number and, if available, fax number When can customer service call? An exact appliance designation: model no.
-
Page 5: Safety Instructions
Safety Instructions This appliance complies with valid safety regulations. Improper handling may cause damage to property and injury to persons. Please read these instructions carefully before installing your appliance and using it. It contains important information and tips on assembly, safety and maintenance. Information concerning structural requirements The following instructions must be observed when cooker hoods are used in the extraction mode:... - Page 6 Safety instructions for assembly and use The metal grease filters must always be in place when the cooker hood is in operation. Greasy vapours may otherwise be deposited in the hood and in the extraction air system. In the case of gas cookers it is important to ensure that the cooking zones are not operated without any cookware.
-
Page 7: Installation
INSTALLATION Depending on the model, a minimum clearance of 60 cm must be maintained between an electric hob and the bottom of the cooker hood when installing the hood. A minimum clearance of 75 cm must be maintained for gas hobs (Fig. 1). Fig. - Page 8 Other important information In order to make sure that ventilation is optimal and that the hood operates quietly, the extraction air system, including the wall box, must be at least 150 mm in diameter. Please observe the following when installing the exhaust air pipe: Use short, straight exhaust air ducts.
-
Page 9: Mounting On A Wall
MOUNTING ON A WALL KD9980.0TGE / KD9980.0BGE dimensioned drawing KD9980.0TGE / KD9980.0BGE dimensioned drawing of installation dimensions (back view) - Page 10 Take the wall mounting bracket shown in Fig. 2 and place it on the wall so that you have the height you want when you mount the cooker hood. Make sure that you maintain a minimum clearance of 60 cm between the hob and the bottom of the cooker hood for electric hobs and a minimum clearance of 75 cm for gas hobs.
- Page 11 You have several options for aligning the hood thanks to its multiaxial mounting system. To align the hood on the right and left hand side, you can either move the wall mounting bracket to the left or right until it is in the ideal position by loosening the screws and then fastening them again (if the hood needs to be moved by more than 0.5 cm) (Fig.
- Page 12 To mount the chimney take the assembly clamp that has been provided (Fig. 5), place it at the required height, generally right below the ceiling (Fig. 5) and then fasten it. You will then need to make the connection for the extraction air and mount the chimneys according to Fig.
-
Page 13: Mounting On The Ceiling
MOUNTING ON A CEILING IKD9980.0TGE / IKD9980.0BGE dimensioned drawing Assembly diagrammes Ceiling Fastening clips Ceiling mounting bracket Fitting panel Motor box Mounting ring Mounting angle Motor box Telescopic chimney... - Page 14 Take the ceiling mounting bracket shown in Fig. 6 and place it on the ceiling so that you have the height you want when you mount the cooker hood. Make sure that you maintain a minimum clearance of 60 cm between the hob and the bottom of the cooker hood for electric hobs and a minimum clearance of 75 cm for gas hobs.
- Page 15 The height of the cooker hood can be adjusted with the mounting angles. You can use sheet metal hooks on the body of the hood to hang up the hood before you finally mount it. Once you have mounted the body of the hood onto the mounting angles, fasten the LED glass panels that have been supplied as shown in Fig.
-
Page 16: Operation
OPERATION This cooker hood is regulated with touch-sensitive sensor controls located on the front of the hood. The controls react when the corresponding symbol is touched lightly. You can regulate the power settings, the lamp, including the brightness level, as well as the automatic delayed stop function with the sensor controls. -
Page 17: Dimmer Function
In this case, in order to make the setting for operating the lighting per sensor key, you will need to touch the sensor key continuously for approx. 5 seconds until bars appear in display 2 (Fig. A). The top bar (Fig. B) is for lighting the LED glass panels and the bottom bar (Fig. -
Page 18: Night Light Function
Night Light function This cooker hood is fitted with a Night Light system which you can use to make a setting so that the lighting switches on automatically when it is dark as soon as the system registers a movement in the kitchen. The lighting then switches off automatically after 30 seconds each time a movement is detected. -
Page 19: Remote Control
IR remote control An IR remote control (Fig. 8) is included with delivery. It can be used to operate and regulate all the functions of the cooker hood from a distance of several metres. To do so, point the remote control towards the cooker hood and press the function of your choice on the remote control. -
Page 20: Maintenance, Cleaning And Care
In the case of models KD9980.0TGE / KD0080.0BGE or IKD9980.0TGE / IKD980.0BGE you can also clean the front metal grease filters in addition to the the bottom metal grease filters. -
Page 21: Grease Filter
Grease filter To remove the grease filter press the bar rail handle of the filter down and remove the grease filter from the hood (Fig. 10). Then remove the grease filter from the stainless steel frame (Fig. 10.2). To replace the grease filter, first of all replace it in the stainless steel frame and then return it to the hood. -
Page 22: Charcoal Filter
Depending on how you cook and fry, the metal grease filters should be cleaned approximately every two weeks. Soak the metal grease filters and stainless steel frames well in hot soapy water, clean them with a soft brush and then spray them thoroughly with hot water to rinse them. - Page 23 The charcoal filter should be replaced after approximately three to six months. The intervals for cleaning and replacement should generally be observed in order to ensure that no greasy vapours are deposited on kitchen walls and units. If the metal filter is not regularly cleaned when the hood is operated in the circulation mode, the charcoal filter will also become clogged more quickly, impairing the operation of the hood.
Need help?
Do you have a question about the KD9980.0TGE and is the answer not in the manual?
Questions and answers