Subscribe to Our Youtube Channel
Related Manuals for U-Line U-3018CLROL-00
Summary of Contents for U-Line U-3018CLROL-00
- Page 1 INSTALL GUIDE ® MODULAR 3000 SERIES 120V, 3018CLR MODELS U-3018CLROL-00 U-3018CLROL-01 U-3018CLROL-40 U-3018CLROL-41 U-3018CLRS-00 U-3018CLRS-01 U-3018CLRS-40 U-3018CLRS-41 The Built-In Undercounter Leader Since 1962 U-LINE.COM...
-
Page 2: Table Of Contents
9 - Level & Install Leveling Information ............................11 Installation................................11 Installation Troubleshooting........................11 10 - Prepare Plumbing Copper Water Supply Connection........................12 U-Line Water Hookup Kit Connection......................12 11 - Drain Connection Gravity Drain ................................13 Factory Installed Drain Pump ..........................13 Drain Connection ..............................14 Final Installation ..............................14... -
Page 3: Safety Precautions
• Failure to clean the condenser every six months can cause the unit to malfunction. This could void the warranty. • Do not Block any internal Fans. Use only genuine U-Line replacement parts. Imitation parts can damage the unit, affect its operation or performance and may void the warranty. -
Page 4: Inspect & Plan
Quick Start Guide and a Registration Card. Please complete and mail the Product Registration Card. You may also register the unit online at u-line.com. Go to the Customer NOTICE Service tab and click on Product Registration. Once your unit is... -
Page 5: Prepare Site
Cut-Out Dimensions 3 Prepare Site 3018CLR Series Your U-Line product has been designed exclusively for a built-in Follow the cut-out drawing. The 18" width allows for ease in installation. When built-in, your unit does not require additional air installation and removal of the unit. 24" is the cabinet depth in most space for top, sides, or rear. -
Page 6: Product Dimensions 3018 Series
Ice Machines 4 Product Dimensions 3018 Series 23-1/4" 33-11/16" 34-11/16" 3-5/8" To 4-5/8" 17-3/4" Solid Overlay Door 24" 33-11/16" 34-11/16" 3-5/8" To 4-5/8" 17-3/4" Stainless Steel Solid Door Installation Guide... -
Page 7: Door Swing Dimensions
Ice Machines Other Site Requirements 5 Door Swing Dimensions Side-By-Side Installation Units have a zero clearance when the door to open 90°. Overlay Cut-out width for a side-by-side installation is the total of the widths models will need additional space for any knobs or pulls installed on listed under Cut-Out Dimensions in each unit’s Installation Guide. -
Page 8: 3000 Series Doors
Ice Machines 3. Gently pull bottom of wrap away from door. 6 3000 Series Doors 4. The wrap hinges on top of the door. Carefully pull wrap away and then up. See below. Door Alignment and Adjustment Align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive Step 2 frost or condensation may form in the interior. -
Page 9: 3000 Series Overlays
Ice Machines 7 3000 Series Overlays Overlay Panel Dimensions Overlay / Frame Overlay Panel BACK SURFACE MUST HAVE AMPLE FLAT SURFACE TO MOUNT OVERLAY PANEL FLAT AND WITHOUT 3/4” INTERFERANCE NOTICE 17 1/2” Due to differences in surrounding cabinetry the panel may not perfectly align with door. - Page 10 6. Secure overlay to door NOTICE using clamps. A robust tape may also be used. Make certain the display cable remains securely seated in Clamp U-Line recommends the the inner door channel, see below. use of bar clamps to securely clamp the Inner Display overlay to the door.
-
Page 11: Overlay Grille
3. Apply double sided tape to the backside of the overlay grill. Use the ™ ™ diagram below for reference. U-Line recommends 3M tape, a high strength bonding tape. Apply Tape To Shaded Area 4. Remove backing paper from double sided tape. -
Page 12: 3000 Series Anti-Tip Bracket
Ice Machines 3018CLR Side Mount 8 3000 Series Anti-Tip Bracket Right Hand Left Hand Anti-Tip Brackets Installation Install On Non-Hinge Side WARNING The Anti-tip bracket must be installed to prevent the unit from tipping when doors are fully opened, or excess weight is placed on the front of the unit. -
Page 13: Level & Install
Ice Machines Installation 9 Level & Install 1. Plug in the power cord. Leveling Information 2. Gently push the unit into position. Be careful to not entangle the electrical cord, water line and drain line. It is recommended that the unit is level once installed. 3. -
Page 14: Prepare Plumbing
8. Locate the U-Line supplied hose fitting. Ensure the end on the copper tubing has been cut straight and is free of burrs. Slide the 1/4” Copper Water Supply Connection... - Page 15 12. Re-attach back panel and front panel. 8. Attach the garden hose connection from the kit to the front of the U-Line Water Hookup Kit Connection unit. 9. Attach the front of the braided line to this garden hose connection.
-
Page 16: Drain Connection
1/4" per CAUTION foot. If your U-Line unit did not come with a factory installed Factory Installed Drain Pump drain pump you must use a gravity style drain connection. -
Page 17: Final Installation
In the event of a power outage, restricted drain or pump failure, the failure to use the U-Line P60 drain pump could NOTICE result in substantial water leakage and pooling with severe... -
Page 18: Product Information
E-mail: onlineparts@u-line.com BUILDING ON THREE GENERATIONS OF INNOVATION For nearly five decades and three generations, U-Line continues to be the leader in innovation, quality and value in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired innovation and attention to even the smallest details.
Need help?
Do you have a question about the U-3018CLROL-00 and is the answer not in the manual?
Questions and answers