GE Profile Advantium JX2201NSS Dimensions And Installation Information

PSB1201NSS
GE Profile Advantium
Advantium Wall Oven Dimensions (in inches)and
Advantium wall oven/GE Profile cooking tower dimensions and cabinet installation information (in inches)
Cabinet Installation (in inches)
Note: 2" minimum
between cutouts when
installed above warming
drawer or single wall oven.
Note: Cabinets installed adjacent Installation Information:
to wall ovens must have an adhesion
Before installing, consult
spec of at least 194° F temperature rating.
installation instructions
packed with product for
current dimensional data.
Note: PSB1200/1 series
Advantium can be
19-1/32"
installed below GE/GE
Profile non-downdraft
gas and electric cooktops.
It CANNOT be installed
below induction or Monogram
(2GU3841385) gas cooktops.
Note: PSB1200/1 series Advantium
oven comes with two lower trim pieces.
One is for use above 36-inch height
installations and one is for use below 36-
inch installations. Use of the accessory
drawer will replace the bottom trim piece
for applicable installations. Please see
installation instructions for full details.
For answers to your Monogram,
®
GE ® appliance questions, visit our website at
ge.com or call GE Answer Center
800.626.2000.
120 Volt - 30" Wall Oven
®
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
Cutout depth
21-1/2"
Excluding
Handle
A
Conduit
(48-1/2"
long)
29-25/32"
30"
GE Profile or
™
® service,
Suitable
bracing
to support
over centerline
runners
of cabinet
(Must support 130 lbs.)
cooking_tower_solid_floor.eps
23-1/2"
4-3/16"
Junction
box location
B
17-1/2"
Construct Solid
Cutout height
Bottom Min.
3/8" Plywood
Advantium Wall Oven Dimensions (in inches)and
Supported by
Cabinet Installation (in inches)
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
5" min.from
floor 1" min.
above toekick
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
C L
2 x 4's or
equivalent
solid floor
PSB1200/1 without
accessory drawer
PSB1200/1 with
accessory drawer
*For existing cutouts a maximum width of 28-1/2" is acceptable
21-5/8"
Cabinet width
A
B
H
D
Excluding
Handle
W
A
B
Conduit
(46" long)
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
21-1/2"
Excluding
Handle
A
adv_240_120_cooktower_dia.eps
Conduit
19-1/32" (48-1/2"
Cabinet W H
long)
Width Width Height
(excluding
(inches)
30 29-25/32 19-1/8 21-3/4
29-25/32"
30 29-25/32 22-1/4 21-3/4
30"
Specification Created 11/08
4-3/16
Junction box location (240-volt models only)
2-1/2" MIN between cutouts
recommended—2" MIN required
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
9-1/4" cutout height
28-1/2" cutout width
2" MIN between cutouts
23-1/2"
1" Min. above toekick or adjust
Cutout depth
to oven installation height
4-3/16"
Junction
box location
B
17-1/2"
D Z
Construct Solid
Cutout height
Depth X Y Cutout
Bottom Min.
Cutout Cutout Depth
3/8" Plywood
handle) Width Height
(minimum)
Supported by
2 x 4 or 1 x 2
25-1/8 17-1/2 23-1/2
Runners, all
Four Sides.
25-1/4 to
(Must Support
21 23-1/2
28-1/2* 150 lbs.)
5" min.from
floor 1" min.
above toekick
Listed by
Underwriters
Laboratories
240446