Page 1
LIFT-O-FLEX® 17000 SP 400 Manual December 2001 Edition Lifter Serial Number: _____________________ Lift Mast Serial Number: ___________________ Intermediate Member Serial No.: _____________ Power Pack Serial No.: _____________________ I, LLC, 9311 Monroe Road, Suite D, Charlotte, NC 28270 Tel (7040 847-2464; Fax (704) 847-6739 Web site: http://www.roni.com E-mail: info@roni.com...
Lift-O-Flex 17000 SP 400 Manual 1. LIFT-O-FLEX 17000 SP 400 LIFT-O-FLEX® is a registered trademark of RONI, LLC, Charlotte NC. NOTE: It is important that you read and fully understand this manual before using your Lift- O-Flex Lifter. If you have any questions contact your distributor or the manufacturer.
Lift-O-Flex 17000 SP 400 Manual OPERATIONAL SAFETY The ergonomic design of LIFT-O-FLEX is by itself an active factor of operational safety. Other factors of security and technical features are as follows: The movement of the load platform will stop should an object be placed in-between the lift frame and the load platform or if other jamming occurs.
Lift-O-Flex 17000 SP 400 Manual 2. Assembly instructions Each lifter is to be delivered in modules and will be shipped in cardboard box(s). Components are as indicated below. Intermediate Section Leg-LH Leg-RH Lift Mast Handlebar w/Remote Controller Electronic Power Pack with ground Brake Rod End-Effector cable attached...
Page 6
Lift-O-Flex 17000 SP 400 Manual Bolted Intermediate Section Lift Motor Intermediate Section-Lock in Place with Quick Disconnect Pin Located on Bolted Intermediate Section Bracket. Pick up the lift mast and carefully insert the mast onto the mounting slide. (A mounting slot is provided full length on the rear of the mast).
Page 7
Lift-O-Flex 17000 SP 400 Manual Take the power package and let it slide into the slot on the rear of the lift mast. Then lower it until it stops just above the mast mounting yoke and tighten the handle. Plug the motor cable into its outlet on the power package.
The European charger may require a plug adapter to fit countries wall socket. The Pacific Rim charger will require a pigtail adapter from standard US plug to plug to fit countries wall socket. Adapter plugs to fit chargers for wall sockets are the responsibility of Hewlett-Packard. Page 7 Rev July 01...
Lift-O-Flex 17000 SP 400 Manual 3.1.2 Handlebar The height of the handlebar can easily be adjusted by loosening the quick disconnect handles and sliding the handlebar to the desired position. After adjustment, tighten the quick disconnect handles. To obtain the best working conditions it is important to adjust the handle to a comfortable level. During movement of the lifter, always keep hands inside the handle.
Lift-O-Flex 17000 SP 400 Manual Directional wheel locks When moving a heavy load, it is both easier and safer if you use the directional wheel locks by moving the red bar into the upper position. Both back wheels are now locked in a straightforward position. This gives greater directional stability when moving heavy loads.
Lift-O-Flex 17000 SP 400 Manual Maintenance Regular maintenance is important to protect the continued use of the LIFT-O-FLEX lifter. Daily maintenance Wash the lifter with a detergent suitable for powder coat surfaces, aluminium and stainless steel. Follow the instructions on the detergent. Wipe the lifter dry. Do not use a high-pressure hose. It could damage both the electronics as well as the chassis.
Lift-O-Flex 17000 SP 400 Manual 4. Enclosures 4.1 Electrical wiring 4.1.1 Wiring for Intermediate Member with brake motor Motor Motor Brake Plug Page 11 Rev July 01...
Lift-O-Flex 17000 SP 400 Manual Part No. 17287 Item No. Description Part No. Brake Rod 174287 4.4.9 Power Pack Note: Ground Cable with alligator clip not shown Part No. 15700E04 Item No. Description Part No. Power Pack Cover 17159 Battery 6V 17548 Battery 12V 17549...
Lift-O-Flex 17000 SP 400 Manual Charger Plug 17327 Base RonI Supplied Insert RonI Supplied Cable Kit 17126 Screw 4.4.10 Lifter Check List During assembly of the LIFT-O-FLEX 17000 SP 400 components are required to be inspected prior to using the lifter. This is to ensure that the lifter will operate safely and ergonomically. Casters swivel and rotate properly Intermediate section assembled to legs with the bolts provided and are secure.
Lift-O-Flex 17000 SP 400 Manual 5. Declaration of Conformity Referring to Directive for machines 89/392/EEC with addendum - appendix 2A Supplier: I,LLC,9311 Monroe Rd, Suite D, Charlotte, NC 28270 Address 17000 SP 400 Description: LIFT-O-FLEX® Regulations: AFS 1993:10 (89/392/EEG) AND (91/368/EEG) Regulations that the lifter complies to.