Summary of Contents for Universal Electronics atlas ocap 5-device
Page 1
ATLAS OCAP 5-Device Remote Control Control remoto de dispositivo ATLAS OCAP 5 Users Guide Guía del usuario PREPROGRAMMED FOR YOUR SET-TOP BOX PREPROGRAMADO PARA SU SET-TOP BOX (aparato integrado de convertidor y descodificador)
INTRODUCTION The Atlas OCAP 5-Device Remote Control by Universal Electronics is our latest generation universal remote control. Its sophisticated technology allows you to consolidate up to five of your original home entertainment remote controls into one easy-to-use product. Moreover, its packed with advanced features such as: •...
FEATURES AND FUNCTIONS Use the illustration below to locate features on the Atlas OCAP 5-Device Remote Control and then study the Key Charts (on the next three pages) to learn how they function. To find out what type of devices can be controlled by each device key after programming, see “Device Table”...
Key Charts Function Use SETUP for all programming sequences. Also use to turn backlighting on and off, if applicable. Press PWR once to turn on or off a home entertainment device. For MASTER POWER control, see “Using the Master Power Key” on page 19. Press VCR, DVD, AUD, TV, or CBL once to select a home entertainment device to control.
Page 7
Function Use VOL+ (or VOL-) to raise (or lower) the audio volume. Use FAV to cycle through your favorite channels stored in your cable converter. Use CH+ (or CH-) to select the next higher (or lower) channel. For DVD players, use these keys to skip forward (or reverse) through chapters.
Please refer to the table below when performing the instructions in “Programming Device Control” on page 10 or “Setting Up a Combo Unit” on page 11. After programming, the Atlas OCAP 5-Device Remote Control will be able to control the following types of devices: Device Key...
Device Key Controls these types of devices Television Cable Box (Converter) or Satellite Receiver INSTALLING BATTERIES ❶ ❷ ❸ On the back of the remote control, push the tab and lift off the battery cover. Locate the two (2) enclosed AA batteries. Match the + and - marks with those in the battery case, then insert them.
PROGRAMMING DEVICE CONTROL The Atlas OCAP 5-Device Remote Control is preprogrammed to operate the cable box (converter) provided by your cable system, an RCA TV, a Toshiba DVD player, an RCA VCR, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps;...
Repeat steps 1 through 4 for each device you want the remote control to operate. For future reference, write down each working device code in the boxes on the following page. VCR Code Device Type:___________________ DVD Code Device Type:___________________ AUD Code Device Type:___________________ CBL Code Device Type:___________________...
SEARCHING FOR YOUR CODE If your home entertainment device does not respond to the Atlas OCAP 5-Device Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
Page 13
Aim the remote control at the TV and press PWR once. Press and release the CH+ key continuously, then stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
CHECKING THE CODES If you have set up the Atlas OCAP 5-Device Remote Control by searching for your device code (on the previous page), you may need to find out which four- digit code is operating your equipment. For example, to find out which code is operating your TV: On the remote control, press TV once;...
Unlocking Channel Control On the remote control, press CBL once; it will blink once. Press and hold SETUP until the CBL key blinks twice. Enter 9 7 3. The CBL key will blink twice. Press CH- once. The CBL key will blink four times.
NOTE: The audio mode’s (AUD) volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will have control of the audio device’s volume in all other modes (i.e., VCR, DVD, TV, and CBL). This can be an advan- tage if, for example, you always listen to home entertainment devices through your receiver’s speakers.
(e.g., TV) is controlled regardless of mode. PROGRAMMING CABLE ID LOCK The Atlas OCAP 5-Device Remote Control is locked at the factory to operate your cable provider’s set top box. However, if you have another brand or model of cable converter or satellite service that you would like to control, then you’ll need to perform the following steps...
Enter 9 8 2. The CBL key will blink twice, indicating ID Lock is again locked. PROGRAMMING MACRO KEYS The Atlas OCAP 5-Device Remote Control includes two macro keys (located directly below the MUTE and LAST keys). Macro keys allow you to set up key macros to activate certain keys in a specific order.
18). If desired, repeat these to clear another Tune- In key. USING THE MASTER POWER KEY The Atlas OCAP 5-Device Remote Control has a unique feature that allows you to sequentially turn up to five of your home entertainment devices on or off with a single key press.
Enter 9 9 5. The last-selected device key blinks twice. Press PWR once. For the first device you want in the power on sequence, press a device key (e.g., CBL) once. Then press PWR once. For the second device in the power sequence, press its key once (e.g, TV).
Press and hold SETUP until the CBL key blinks twice. RE-ASSIGNING DEVICE KEYS The Atlas OCAP 5-Device Remote Control can be set up to control a second device of an already-assigned type. For example, to have the unit control a TV, a Cable...
ACTIVATING BACKLIGHTING (OPTIONAL) On some models of your Atlas OCAP 5-Device Remote Control, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key. To enable backlighting...
TROUBLESHOOTING PROBLEM: Device key does not blink when you press a key. SOLUTION: Replace the batteries with two (2) new AA batteries (see “Installing Batteries” on page 9). PROBLEM: Device key blinks when you press a key, but home entertainment device does not respond. SOLUTION: Make sure you are aiming the remote control at your home entertainment device and that you are within 15 feet of the device you are trying to control.
Xwave 1001 Yamaha 0490, 0539, 0545 Zenith 0503, 0591, 0741, 0869 Zoece 1265 Setup Codes for DVD Recorders Códigos de configuración para grabadoras de DVD Accurian 1416 Apex Digital 1056 Aspire Digital 1168 Coby 1086 CyberHome 1129, 1502 Funai 0675, 1334 Gateway 1073, 1158 Go Video...
Need help?
Do you have a question about the atlas ocap 5-device and is the answer not in the manual?
Questions and answers