Toshiba IK-WR14A Quick Start Manual And Important Safeguards
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Security Camera
  5. IK-WR14A
  6. Quick start manual and important safeguards

Toshiba IK-WR14A Quick Start Manual And Important Safeguards

Network cameras
Hide thumbs Also See for IK-WR14A:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual

NETWORK CAMERA

Model: IK-WR14A
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF file) contained in the CD-ROM for settings, operations
and other information.
The application Adobe Reader is needed to view PDF files. If you do not have this
application, download it from the Adobe Systems Incorporated website.
n http://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Website:
n http://www.toshibasecurity.com
If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

Advertisement

Table of Contents
loading

Related Manuals for Toshiba IK-WR14A

Summary of Contents for Toshiba IK-WR14A

  • Page 1: Network Camera

    The application Adobe Reader is needed to view PDF files. If you do not have this application, download it from the Adobe Systems Incorporated website. n http://www.adobe.com/ For information on our latest products and peripheral devices, refer to the following Website: n http://www.toshibasecurity.com If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

  • Page 2: Introduction

    Introduction FCC (USA)-INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 3: Terms And Trademarks

    Thank you for purchasing the IK-WR14A Network Camera. Before using the camera, read this quick start guide carefully to ensure correct usage. After reading this quick start guide, save it for future reference. The design, specifications, software, and quick start guide contents are subject to change without prior notice.

  • Page 4: Table Of Contents

    Table of Contents Introduction FCC (USA)-INFORMATION ..................2 Terms and Trademarks ....................3 Table of Contents....................4 Important Safeguards ..................5 Important Safeguards (Cont.) ................7 Notes on Use and Installation................8 Setting the Network Camera Environment ............9 Items needed for network camera monitoring ............9 Contents ......................

  • Page 5: Important Safeguards

    Important Safeguards 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. Warnings Comply with all warnings on the product and in the user's manual. 4.
  • Page 6 12. Lightning For additional protection on this camera during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the camera due to lightning and power-line surges.

  • Page 7: Important Safeguards (Cont.)

    Important Safeguards (Cont.) CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage"...

  • Page 8: Notes On Use And Installation

    Notes on Use and Installation l Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. l Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen.

  • Page 9: Setting The Network Camera Environment

    Setting the Network Camera Environment Items needed for network camera monitoring l Administrator's personal computer The personal computer that allows setting, operating, monitoring and other functions with the network camera is called the "administrator's personal computer" in this guide. * The personal computer for viewing monitored images is called the "user's personal computer"...

  • Page 10: Contents

    Package Contents l IK-WR14A l AV Out cable l CD-ROM l Alignment Sticker/Mounting Plate l Warranty Card l Quick Start Guide and Important Safeguards l Waterproof Connector & Bushing l Gasket, Torx Wrench, Silica Gel and tape, Hex Nut , Screws and Anchors...

  • Page 11: Physical Description

    Physical Description Camera Base Dome Cover Cover screws Side Opening Cover NOTE Replace the side opening cover with the supplied bushing if you want to route cables from the side of camera. The 1/2" (12.7mm) protection conduits and tubing are not supplied. 11 11...
  • Page 12 8. 12V DC Output DIP switch Microphone Video Output 10/100BaseT NTSC internal 60Hz Ethernet Socket MIC In (Printed "Audio In") external Audio/Video Out 50Hz (Printed "AV Out") NOTE Fix microphone switch to the external, because IK-WR14A doesn't have built-in microphone.

  • Page 13: Hardware Installation

    Hardware Installation First, use the supplied torx wrench to detach the dome cover from the camera base. Then, follow the steps below to install the camera; either to a ceiling or to a wall. Bottom of the Camera NOTE Record the MAC address under the camera base before installing the camera.
  • Page 14 Waterproof Connector Sealing Nut (A) Housing (B) Seals (C) Seal (D) Screw Nut (E) Hex Nut (F) Assembling Steps 1. D i s a s s e m b l e t h e c o m p o n e n t s o f t h e waterproof connector into parts (A) ~ (E) as shown above.

  • Page 15: Cable Installation

    3. You will need an RJ45 crimping tool to attach the Ethernet wires to a connec- tor. When done, connect the cable to the camera’s Ethernet socket . NOTE o: white/orange stripe O: orange solid g: white/green stripe RJ45 crimping tool and plug are not B: blue solid b: white/blue stripe included.
  • Page 16 CAUTION l Installation should be done only by qualified personnel and conform to all local codes. l Install this camera on a firm and solid part of the ceiling or wall. If installed improperly or on a weak surface, the camera could fall causing injury and damage.

  • Page 17: Network Deployment

    Network Deployment Power over Ethernet (PoE) When using a PoE-enabled switch The camera is PoE-compliant, allowing transmission of power and data via single LAN cable. See the following illustration to connect the camera to a PoE switch via LAN cable. Client PC (not supplied) PoE switch...
  • Page 18 General Connection (without PoE) 1. Connect the camera to an Ethernet switch via LAN cable. 2. Connect the power cable from a power unit (not supplied) to the appropriate port of the general I/O terminal. (See page 12). 3. Connect the PC to an Ethernet switch via Ethernet cable. Ethernet switch (not supplied) Client PC...

  • Page 19: Assigning Ip Address

    Assigning IP Address 1. Install the "Installation Wizard" under the Software Utility directory from the CD- ROM. 2. The program will analyze your network environment. After your network is analyzed, please click on the "Next" button to continue the program. Installation Wizard 3.

  • Page 20: Retrieving Images

    Retrieving Images 1. Access the Network Camera from the network. ® 2. Retrieve live video through Internet Explorer For more information on camera configuration, please refer to user's manual on the CD-ROM.

  • Page 21: Adjusting The Lens

    Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by performing the following: To adjust the viewing angle 1. Turn the lens module left and right. 2. Loosen the tilt adjustment screws on both side of the camera and then turn the lens module up and down.

  • Page 22: Dome Cover

    Dome cover 1. Attach the dome cover to the camera and aligning with the mounting holes. 2. You will find a silica gel bag attached to the dome cover. Remove the supplied silica gel from the aluminum foil bag, and replace it to new silica gel with supplied double-sided tape.

  • Page 23: Adjusting The Zoom And Focus

    Adjusting the Zoom and Focus Access the Network Camera from the browser interface, and click the configuration button onthe main page. Then click the following: Audio and Video Image Zoom and Focus To adjust the zoom factor and focus range 1.
  • Page 24 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. Surveillance & IP Video Products 9740 Irvine Boulevard, Irvine, CA 92618-1697 Phone Number: (877) 855-1349 625016700G...

Table of Contents