Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Goldmund APOLOGUE
Summary of Contents for Goldmund APOLOGUE
- Page 1 THE GOLDMUND APOLOGUE SPEAKER SYSTEM OWNER MANUAL...
- Page 2 Please do not unpack or connect any part before reading the following instructions. Very important: The Apologue speakers' parts being very heavy and voluminous but at the same time fragile, it is imperative that a minimum of three people assist during their mounting.
- Page 3 1. Preliminaries For exacting technicians, musicians, and people who demand the very best in audio reproduction, we strongly recommend the use of the best associated components, especially concerning electronics and cables (see paragraph 10). Warning : If you need to return the speakers to the factory or to your local representative for a warranty repair, please note that they must be repacked in the original package.
- Page 4 3. Cartons and contents The speaker system is packed in 12 large cartons, each marked of a different name. Here is the list of contents of each of the carton. • Frame carton : ∗ 2 identical square bases. ∗ 2 top bars of the frame. ∗...
-
Page 5: Frame Mounting
4. Frame mounting For each speaker you will need : - 1 square base (Frame) - 2 long frame legs (Frame long) - 1 top bar of the frame (Frame) - 8 flat-head screws (Tweeters) Locate the square base in the future position of your speaker, the two vertical attachements upwards and towards the listener position. - Page 6 5. Bottom woofer mounting For each speaker you will need: - 1 bottom woofer section (Bottom Woofer Right or Left) - 2 cylindrical threaded feet (Tweeters) - 2 threaded bars (Tweeters) Warning : The woofer's pointed foot is very hard. It is built to pass through a carpeted floor. If your floor is made of wood or tiles, be careful not to scratch it by moving the woofer section without lifting it.
- Page 7 6. Top woofer connection and mounting. For each speaker you will need: - 1 top woofer section (Top Woofer Right or Left) - 2 threaded bars (Tweeters) - 4 molettes (Molettes) Place the top woofer behind the bottom woofer, near its definite position, with its cable directed towards the bottom woofer, in order to facilitate the connection of the cable to the bottom crossover section located on top surface of the bottom woofer.
- Page 8 7. Bottom tweeter mounting. For each speaker you will need: - 1 bottom tweeter (Tweeters) - 4 plastic translucid feet (Tweeters) - 1 fake piece of wire (Tweeters) - 1 arm among the shortest (Frame) - 1 frame rectangular arm holder (Tweeters) - 1 cylindrical head screw (Tweeters) - 2 flat head screws...
-
Page 9: Midrange Mounting
8. Midrange mounting For each speaker you will need: - 1 midrange section (Midrange Right or Left) - 1 arm among the medium length (Frame) - 1 frame rectangular arm holder (Tweeters) - 1 cylindrical head screw (Tweeters) - 2 flat head screws (Tweeters) - 1 threaded bar (Tweeters) - Page 10 9. Top tweeter mounting. For each speaker you will need: -1 top tweeter (Tweeters) - 2 plastic translucid feet (Tweeters) - 1 fake piece of wire (Tweeters) - 1 arm among the longest (Frame) - 1 frame rectangular arm holder (Tweeters) - 1 cylindrical head screw (Tweeters) - 2 flat head screws...
- Page 11 10. Midrange crossover connection. The cables coming from the different sections as well as the cable coming from the midrange section back panel have to be connected to the crossover connection bar (See figures 2). This bar is located inside the back openning of the midrange section.
-
Page 12: Connection To The Amplifier
If you are not using a Goldcube, the only amplifier fast enough to drive properly the Apologue is one of the Goldmund Mimesis. Any slower amplifier will not have the capability to properly hold the ultra-fast drivers of the Apologue.
Need help?
Do you have a question about the APOLOGUE and is the answer not in the manual?
Questions and answers