Advertisement
Quick Links
Advertisement
Related Manuals for Goldmund EPILOGUE 3
Summary of Contents for Goldmund EPILOGUE 3
- Page 1 THE GOLDMUND EPILOGUE 3/4 SUB-BASS SPEAKER SYSTEM USER MANUAL...
- Page 2 THE GOLDMUND EPILOGUE 3/4 SUB-BASS SPEAKER SYSTEM USER MANUAL...
- Page 3 Nevertheless, if the instructions are perfectly carried out, you will notice that the sound quality of your Goldmund Epilogue system is incredibly dynamic, precise and sweet. NOTE : The speaker has been assembled for a full testing at the factory with the associated other speakers.
- Page 4 1. PRELIMINARIES The Goldmund Epilogue 3/4 uses the same very innovative technology than the Epilogue 2 to achieve a level of definition and neutrality never found before in a sub- bass speaker system. Please read very carefully the following instructions. This high-precision speaker is extremely revealing and can provide the best sound only if it is used properly.
- Page 5 To manipulate safely the Epilogue 3/4, you need to use accessories located in the separate accessory box that your dealer has received, called the "Helm" box. Open the "Helm" box. Locate the front panel attachment block (the heavy steel block) and plug it on the two steel bars protruding from the lower part of the speaker front panel (the large circular hole must be directed toward the floor).
- Page 6 4. ADJUSTING THE EPILOGUE 3/4 FEET When the Epilogue 3/4 is set in position, the 4 adjustable corner feet must be adjusted as follow. The two front feet are only set to avoid the speaker to balance if it moved. They must go down to the floor without pressure.
- Page 7 B. Epilogue 2 preparation • Dismount the top silver steel plate. • Dismount the two gold plated side identification plates. • Reassemble the silver steel plate in one of the lateral sides (one of the larger sides). Use the side which is the closest to the coaxial connector located on the back panel and noted Epilogue 1.
- Page 8 • Keep the U shaped part found in the Epiframe 1 carton for the upper satellite frame assembly. E. Installation of the lower satellite • Take two short transparent plexiglas feet found in the Epiframe cartons (they are all identical). Put them standing on top of the Epilogue 3. Their height is 5cm. •...
-
Page 9: Speakers Physical Alignment
• Arrange the two transparent feet to be aligned with the back corners of the speaker. • When the Epilogue 1 is in position, attach the two lateral arms of the frame to its sides using the long Steel screws, the golden nuts, 2 teflon ring and the cylindrical "molette". - Page 10 The only connections needed are the Power cord and the interconnect linking the Epilogue 3 to the output of the preamplifier, or if you use the Epilogue 4 in digital, use a digital link cable for input. The Epilogue 3/4 may receive two analogue cables if one only one Epilogue 3/4 is used so the right and left channels may be mixed automatically inside the crossover.
- Page 11 Try using highest quality banana plugs which can be tighten in position. However, it is far better to use the Goldmund Speaker Cable to allow the speed of the amplifier to properly control the drivers. Any speaker cable of lower quality or speed can ruin the sonic capabilities of the Epilogue System.
- Page 12 Try using highest quality banana plugs which can be tighten in position. However, it is far better to use the Goldmund Speaker Cable to allow the speed of the amplifier to properly control the drivers. Any speaker cable of lower quality or...
- Page 13 Try using highest quality banana plugs which can be tighten in position. However, it is far better to use the Goldmund Speaker Cable to allow the speed of the amplifier to properly control the drivers. Any speaker cable of lower quality or...
- Page 14 When using the Goldmund Speaker Cable, the Speaker Adapter can be avoided and the coaxial cable directly connected to the large coaxial connectors provided on the speaker back panel. The sonic improvement which can be achieved in the best systems is quite dramatic.
- Page 15 Y connectors, it may be necessary to have a separation box built especially for this atypical application. Please consult your Goldmund dealer for advice. For best performance, use a preamplifier with very low output impedance so several amplifiers may be used without signal loss.
-
Page 16: Specifications
SPECIFICATIONS Epilogue 3/4 Amplifier Analogue Input Impedance : > 100 kOhms. Amplifier maximum power : 500 W Rms. Bandwidth : • Low Frequency Cutoff : < 22 Hz -3dB. Drivers : 8 x 21 cm Velvet Kevlar proprietary drivers mounted 4x2 in inverted push-pull with front speaker mounted backwards.
Need help?
Do you have a question about the EPILOGUE 3 and is the answer not in the manual?
Questions and answers