Download  Print this page

GE DECT 6.0 CORDLESS HANDSET 28110 Quick Setup Manual

For optional/additional model dect 6.0 cordless handset for use with systems 28111 and 28112 series.
Hide thumbs
   

Advertisement

Quick Set-Up Guide
for Optional/Additional
Model 28110 DECT 6.0

Cordless Handset

for use with Systems
28111 and 28112 Series

Important Information

NOTICE: This product meets the applicable Industry Canada technical
specifications.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including interference
that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe systems, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone
company.
Interference Information
This equipment generates and uses radio frequency energy which may interfere
with residential radio and television reception if not properly installed and used in
accordance with instructions contained in this manual. Reasonable protection against
such interference is ensured, although there is no guarantee this will not occur in a
given installation. If interference is suspected and verified by switching this equipment
on and off, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient the radio/television receiver's antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into separate
circuit outlets. The user may also wish to consult a qualified radio/television technician
for additional suggestions. This equipment has been fully tested and complies with all
limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC/Industry Canada standards for Hearing Aid
Compatibility.
THE LIGHTNING
FLASH AND ARROW
WARNING: TO
HEAD WITHIN THE
PREVENT FIRE OR
TRIANGLE IS A
WARNING SIGN
ELECTRICAL SHOCK
ALERTING YOU OF
HAZARD, DO NOT
"DANGEROUS
VOLTAGE" INSIDE
EXPOSE THIS
THE PRODUCT.
PRODUCT TO RAIN
SEE MARKING ON BOTTOM / BACK OF PRODUCT
OR MOISTURE.
Model 28110
00016116 (Rev. 2 CAN E)
06-46
Printed in China
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE EXCLAMATION
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
POINT WITHIN THE
TRIANGLE IS A
NOT REMOVE COVER (OR
BACK). NO USER
WARNING SIGN
SERVICEABLE PARTS INSIDE.
ALERTING YOU OF
REFER SERVICING TO
IMPORTANT
QUALIFIED SERVICE
INSTRUCTIONS
ACCOMPANYING
PERSONNEL.
THE PRODUCT.
Thomson Digital Technologies Ltd.
© 2006 Thomson Digital Technologies Ltd.
Trademark(s) ® Registered
Marque(s) ® déposée(s

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter."
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines
Introduction
CAUTION: When using telephone equipment, there are basic
safety instructions that should always be followed. Refer to the
IMPORTANT SAFETY INSTRUCTIONS provided with this product
and save them for future reference.
IMPORTANT: Because cordless phones operate on electricity, you
should have at least one phone in your home that isn't cordless, in
case the power in your home goes out.
If you have purchased an extra handset apart from your original
purchased unit you may find a detailed description of its functions in
the User's Guide provided with your original purchased unit.
If you have purchased an extra handset that is not of the same type
as your original handset you may still use the original User's Guide
to help explain the new handsets basic functions and options.

Parts Checklist

Make sure your package includes the items shown here.
Charge
Battery
Cradle
compartment
cover

Installing the Handset Battery

NOTE: You must connect the handset battery before use.
CAUTION: To reduce the risk of fire or personal injury, use only
the Thomson Inc. approved Nickel-metal Hydride battery model
5-2721, which is compatible with this unit.
1. Locate battery and battery door which are packaged together inside a plastic
bag and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
NOTE: To ensure proper battery installation, the connector is keyed
and can be inserted only one way.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Place the handset in the base to charge.
Extra Charging Cradle
1. Plug the AC power adaptor of the extra charging cradle into the electrical outlet.
NOTE: This power adaptor is intended to be correctly orientated in a
vertical or floor mount position.
2. Place the handset in the extra charging cradle. The charge indicator turns on,
verifying the battery is charging.
3. Allow the phone to charge for 16 hours prior to first use.
Registration
YOU MUST REGISTER THE HANDSET TO THE MAIN BASE BEFORE USE!
After the optional handset has charged for 16 hours on the extra charger,
NEEDS REGISTRATION shows in the display.
1. Press the mute/program button. HOLD BASE PAGE FOR 5 SECONDS, THEN
PRESS HANDSET PROGRAM shows in the display. (Your handset should be held
near the base during registration process.)
2. Press and hold the page button on the base unit until the charge/in use indicator
flashes. Press the handset mute/program button. REGISTERING shows in the
display. HANDSET X REGISTERED shows in the handset display, where X is the
handset number. You may now rename your handset. (Refer to Naming the
Handset Section.)

Naming the Handset

1. Use the touch-tone pad to enter a name (up to 15 characters).
NOTE: If you make a mistake, use the delete button to backspace
and delete one character at a time.
2. Press the mute/program button to save your name. You will hear a confirmation
)
tone and the handset name shows in the display.
Handset
Belt
battery pack
clip
Handset
HANDSET
DECT
TALK
CALL
BACK
format
delete
conf
SPEAKER
redial
program
mute
int
1
3
2
DEC
ABC
4
6
5
MNO
GHI
JKL
7
9
PO
8
WX
RS
YZ
TUV
exit
#
0
OP
ER
memory
flash

Advertisement

Table of Contents

   Also See for GE DECT 6.0 CORDLESS HANDSET 28110

   Related Manuals for GE DECT 6.0 CORDLESS HANDSET 28110

   Summary of Contents for GE DECT 6.0 CORDLESS HANDSET 28110

  • Page 1: Fcc Rf Radiation Exposure Statement

    Quick Set-Up Guide for Optional/Additional Model 28110 DECT 6.0 Cordless Handset for use with Systems 28111 and 28112 Series Important Information NOTICE: This product meets the applicable Industry Canada technical specifications. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 2: Intercom Operation

    De-Registration De-registration cancels registration. During the de-registration process, keep the handset near the base. From the Handset Setup Menu: 1. Press the caller ID-volume ( 6 or 5) button to scroll to the DEREGISTRATION sub- menu. 2. Press the mute/program button to enter the menu. DEREGISTRATION 1YES 42NO - - - shows in the display The default setting is "2NO".

This manual is also suitable for:

Dect 6.0 cordless handset 28111Dect 6.0 cordless handset 2811228110ee1 - dect 6.0 expansion handset

Comments to this Manuals

Symbols: 0
Latest comments: