Advertisement
2. Press the memory button.
NOTE: If you enter a wrong letter, press ch/delete
3. Press the desired memory location. Example, press the
button to backspace.
number 1 key to store the record in memory location 1.
6. Press the memory button to save the name. The display
4. The display shows RING TONE .
shows ENTER TEL NUMBR .
5. Use the
or
button or the touch tone pad to select one
7. Use the number pad to enter the telephone number you
of six ring tones.
want to store (up to 24 digits).
NOTE: The selected ring tone is generated if the Caller
8. Press memory to save the number, and the display shows
RING TONE >1 .
ID information matches the memory location.
6. Press memory to save the number, and the display shows
9. Use the
or
button or the touch tone pad to select
ANIMATION .
one of six ring tones.
7. Use
or
button or the touch tone pad to select one of
NOTE: The selected ring tone is generated if the Caller
five animations or to turn off the animation. The current
ID information matches the memory location, which
animation shows on the first line of the display.
must be a 10-digit number (including area code). This
8. Press memory to save the selected animation for this
usually occurs after the first ring. The current ring tone is
memory location. You will hear a confirmation tone.
generated by a buzzer.
To replace a CID record stored in a memory location
10. Press memory to save the number, and the display shows
with a new CID record:
ANIMATION .
1. Repeat steps 1 through 3.
11. Use the
or
button or the touch tone pad to select one
2. Press the memory button and REPLACE MEMO? shows in
of five animations or to turn off the animation. The current
the display.
animation shows on the first line of the display.
3. Press *tone/exit to exit, or press memory again and the
new CID record replaces the old CID record in that
NOTE: Remember to press flash/program set animation
memory location. You will hear a confirmation tone.
as KNOWN CALLERS or ALL CALLS, and the selected
animation will show in the display if the Caller ID
D
C
CID R
ELETING THE
URRENT
ECORD
number exactly matches the memory location.
1. Make sure the phone is OFF (not in TALK mode).
12. Press memory to save the selected animation for this
memory location. You will hear a confirmation tone.
2. Use the
or
button to display the desired CID record.
3. Press ch/delete. The display shows DELETE?
C
HANGING A
4. Press *tone/exit to exit, or press ch/delete again to erase the
record. You will hear a confirmation tone. The display shows
1. Repeat steps 1 through 10 in Storing a Name and Number
DELETED . Then the next CID record shows in the display.
in Memory.
2. Press the memory button and REPLACE MEMO? shows in
D
A
R
ELETING
LL
ECORDS
the display.
1. Make sure the phone is OFF (not in TALK mode).
3. Press *tone/exit to exit, or press the memory button to
2. Use the
or
button to display any CID record.
store the number. You will hear a confirmation tone.
3. Press and hold ch/delete button until the unit beeps and
S
R
DELETE ALL? shows in the display.
TORING A
4. Press *tone/exit to exit, or press ch/delete again to erase
1. Repeat steps 1 through 6 in Storing a Name and
all records. You will hear a confirmation tone, and the
Number in Memory.
display shows NO CALLS .
2. Press the redial button.
D
C
ID N
3. Repeat steps 8 through 12 in Storing a Name and Number
IALING A
ALLER
UMBER
in Memory.
1. Make sure the phone is OFF (not in TALK mode).
To replace an old redial number with a new redial number:
2. Use the
or
button to display the desired CID record.
1. Repeat steps 1 through 6 in Storing a Name and
3. Press TALK/CALLBACK button. The number
Number in Memory.
dials automatically.
2. Press the redial button and the redial number will be
shown on the display.
C
CID
HANGING THE
3. Repeat steps 8 through 11 in Storing a Name and
Number in Memory.
N
F
UMBER
ORMAT
4. Press the memory button and REPLACE MEMO? shows in
the display.
The format button lets you change the format of the displayed
CID number. The available formats are as follows.
5. Press *tone/exit to exit, or press the memory button
again and the new redial number replaces the old redial
7-digit
7-digit telephone number.
number in that memory location. You will hear a
10-digit
3-digit area code + 7-digit telephone number.
confirmation tone.
11-digit
long distance code "1" + 3-digit area
code + 7-digit telephone number.
D
S
IALING A
TORED
1. Use the
or
button to scroll to the number you want
to call back.
1. Make sure the phone is ON by pressing the TALK/
CALLBACK button.
2. If the number will not dial as shown, press the format
button. Repeat if necessary, until the correct number of
2. Press memory button.
digits are shown.
3. Press the number (0-9) for the desired memory location.
3. Press TALK/CALLBACK button. The number
The number dials automatically.
dials automatically.
M
1. Make sure the phone is OFF (not in TALK mode).
EMORY
2. Press memory button.
Store up to 10 24-digit numbers in memory for quick dialing.
3. Use the
or
button to scroll through the numbers
This memory feature is in addition to the 40 Caller ID records
stored in memory until the desired number is shown.
that can be stored in the Caller ID memory log.
4. Press TALK/CALLBACK. The numbers dial automatically.
S
N
N
TORING A
AME AND
UMBER IN
IMPORTANT: If you make test calls to emergency
numbers stored in memory, remain on the line and briefly
M
EMORY
explain the reason for the call to the dispatcher. Also, it's a
good idea to make these calls in off-peak hours, such as
1. Make sure the phone is OFF (not in TALK mode).
early morning or late evening.
2. Press the memory button.
3. Press the desired memory location (0 through 9).
I
NSERTING A
4. Press the memory button again. The display shows ENTER
D
S
NAME (up to 15 characters).
IALING
EQUENCE
NOTE: If you don't want to enter the name, skip step 5.
When storing information in memory, press the # pause
5. Use the number pad to enter the name (up to 15
button twice within one second to insert a delay in the dialing
sequence of a stored telephone number when a pause is
characters). For example, to enter the name Bill Smith,
needed to wait for a dial tone (for example after you dial 9 for
press the two key twice for the letter B, press the four key
an outside line, or to wait for a computer access tone). PAUSE
three times for the letter I, and press the five key three
times for the letter L. After one second, press the five key
shows on the display as a "P . " Each pause counts as 1 digit in
three times again for the second letter L and press the one
the dialing sequence.
key to insert a space between the letter L and S. Press the
seven key four times for the letter S, press the six key
once for the letter M, press the four key three times for the
letter I, press the eight key once for the letter T, and press
the four key twice for the letter H.
R
D
EVIEWING AND
ELETING
S
N
TORED
UMBERS
1. Press memory, then use the
or
button to view the entry.
2. While the entry is displayed, press the ch/delete button to
delete the entry. The display shows DELETE?
3. Press *tone/exit to exit, or press ch/delete again to delete the
entry. DELETED shows in the display.
C
D
M
HAIN
IALING FROM
EMORY
Use this feature to make calls which require a sequence of
numbers such as using a calling card for a frequently called
long distance number. Each part of the sequence is dialed
from memory. The following example shows how you can use
chain dialing to make a call through a long distance service:
The Number For
Memory Location
Long distance access number
Authorization code
Frequently called long distance number
1. Make sure the phone is ON.
2. Press memory, and then press 7.
3. When you hear the access tone, press memory again and
then press 8.
4. At the next access tone, press memory and then 9.
TIP: Wait for the access tones between pressing the memory
S
N
TORED
UMBER
button, or your call might not go through.
C
B
HANGING THE
ATTERY
Make sure the telephone is OFF before you replace battery.
1. Remove the battery compartment door.
2. Disconnect the battery plug from the jack in
the dialing pad and remove the battery pack.
3. Insert the new battery pack and connect the
N
EDIAL
UMBER
cord into the jack inside the dialing pad.
4. Put the battery compartment door back on.
5. Place dialing pad in the base to charge.
Allow the battery to properly charge (for 12
hours) prior to first use or when you install a
new battery pack. If you do not properly charge
the phone, battery performance will be compromised.
CAUTION: To reduce the risk of fire or personal
injury, use only the battery 5-2522.
B
S
P
ATTERY
AFETY
RECAUTIONS
•
Do not burn, disassemble, mutilate, or puncture. Like
other batteries of this type, toxic materials could be
released which can cause injury.
•
To reduce the risk of fire or personal injury, use only the
battery listed in the User's Guide.
•
Keep batteries out of the reach of children.
•
Remove batteries if storing over 30 days.
N
G
P
C
UMBER
ENERAL
RODUCT
ARE
To keep your telephone working and looking good, follow
these guidelines:
•
Avoid putting the phone near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
•
DO NOT expose to direct sunlight or moisture.
- OR -
•
Avoid dropping and other rough treatment to the phone.
•
Clean with a soft cloth.
•
Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
•
Retain the original packaging in case you need to ship the
phone at a later date.
C
P
R
AUSES OF
OOR
ECEPTION
•
Aluminum siding.
•
Foil backing on insulation.
•
Heating ducts and other metal construction can shield
radio signals.
P
AUSE IN THE
•
You're too close to appliances such as microwaves,
stoves, computers, etc.
•
Atmospheric conditions, such as strong storms.
•
Base is installed in the basement or lower floor of
the house.
•
Base is plugged into an AC outlet with other
electronic devices.
•
Baby monitor is using the same frequency.
•
Battery is low.
•
You're out of range of the base.
•
The headset is not plugged in correctly
T
D
M
ELEPHONE
ISPLAY
ESSAGES
No dial tone
The following indicators show the status of a message or of
•
Check installation:
the unit.
Make sure the base power cord connected to a
INCOMPLETE DATA
Caller information has been
working outlet.
interrupted during transmission or
the phone line is excessively noisy.
Make sure the telephone line cord connected to the base
unit and the wall jack.
ENTER NAME
Prompt telling you to enter
•
Ensure the headset is correctly plugged into the
the name for one of the 10
dialing pad.
memory locations.
ENTER TEL NUMBR
Prompt telling you to enter the
•
The dialing pad may be out of range of the base. Move
telephone number for one of the
closer to the base.
10 memory locations.
•
Disconnect the base from the wall jack and connect
another phone to the same jack. If there is no dial tone in
DELETE?
Prompt asking if you want to
erase Caller ID records or one of
the second phone, the problem might be your wiring or
the 10 numbers stored in the
local service.
phone's outgoing memory.
•
Make sure the battery is properly charged (12 hours).
DELETE ALL?
Prompt asking if you want to
•
Make sure the battery pack installed correctly.
erase all Caller ID records.
7
•
Did the dialing pad beep when you pressed the TALK/
DELETED
Prompt confirming the Caller ID /
8
CALLBACK button? Did the display indicator turn on? The
Memory record is erased.
battery may need to be charged.
9
END OF LIST
Indicates that there is no
Dial tone is OK, but can't dial out
additional information in
• Make sure the tone/pulse setting is programmed correctly.
Caller ID memory.
Unit does not ring
NEW
Indicates call or calls have not
been reviewed.
•
Make sure the RINGER switch on the dialing pad is
turned to ON.
MUTE ON
Indicates that the mute function is
activated, the far end party cannot
•
You may have too many extension phones on your line.
hear your voice, but you can hear
Try unplugging some phones.
his/her. Press format/mute button
•
See solutions for "No dial tone. "
again to deactivate the mute.
You experience static, noise, or fading in and out
UNKNOWN NAME/
The incoming call is from
CALLER/NUMBER
an area not serviced by
•
Change channels
Caller ID or the information was
•
The dialing pad may be out of range of the base. Move
not sent.
closer to the base.
PAGING
Someone has pressed the page
•
Relocate the base.
button on the base.
•
Charge battery.
BLOCKED CALL
The person is calling from a
number that has been blocked
•
Ensure the headset is correctly plugged into the
from transmission.
dialing pad.
•
Make sure base is not plugged into an outlet with another
BLOCKED NAME
The person's name is blocked
household appliance.
from transmission.
REPT
Repeat call message. Indicates that
Unit beeps
a new call from the same number
•
Place dialing pad in base for 20 seconds to reset the security
was received more than once.
code. If that doesn't work, charge battery for 12 hours.
NO DATA
No Caller ID information
•
Clean charging contacts on dialing pad and base with a
was received.
soft cotton cloth.
EMPTY
Indicates a memory location
•
See solutions for "No dial tone. "
is vacant.
•
Replace the battery.
NO CALLS
Indicates no CID records have
been stored.
Memory Dialing
MESSAGE WAITING
Indicates a message is available.
•
Did you program the memory location keys correctly?
•
Did you follow proper dialing sequence?
MSG WAITING OFF
Indicates a message
is deactivated.
•
Make sure the tone/pulse setting is programmed correctly.
•
Did you reprogram numbers into memory after power
PRESS TALK KEY
Prompt indicating the Caller ID
outage or battery replacement?
number is a direct dial number
(DDN) that can not be formatted.
The CHARGE/IN USE indicator on the base flashes
•
Make sure the battery is installed correctly in dial pad.
UNABLE TO DIAL
Indicates the Calling number
•
Provided your phone company offers voice messaging
is incomplete and can not be
dialed out.
service and you subscribe to it, the CHARGE/IN USE
indicator on the base flashes when the phone is not in use
to indicate there is a message waiting. It stops flashing
D
P
S
S
IALING
AD
OUND
IGNALS
after the message has been reviewed.
Signal
Meaning
S
ERVICE
A long warbling tone
Signals an incoming call
If trouble is experienced with this equipment, for repair or warranty
(with ringer on)
information, please contact customer service at
Two long beeps
Confirmation Tone
1-800-448-0329. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect
One short and one long beep
Page signal
the equipment until the problem is resolved.
One short beep
Low battery warning
This product may be serviced only by the manufacturer or its
every seven seconds
authorized service agents. Changes or modifications not
Three short beeps
Error Tone
expressly approved by ATLINKS USA, Inc. could void the
user's authority to operate this product. For instructions on
how to obtain service, refer to the warranty included in this
T
T
ROUBLESHOOTING
IPS
guide or call customer service at 1-800-448-0329.
Or refer inquiries to:
C
ID S
ALLER
OLUTIONS
ATLINKS USA, Inc.
No Display
Manager, Consumer Relations
P O Box 1976
•
Ensure the battery is fully charged. Try replacing the battery.
Indianapolis, IN 46206
Make sure the battery is properly installed and connected.
Attach your sales receipt to the booklet for future reference or jot
•
If you are using AC power, make sure that the
down the date this product was purchased or received as a gift.
unit is connected to a non-switched electrical
This information will be valuable if service should be required
outlet. Disconnect the unit from the plug and plug
during the warranty period.
it in again.
•
You must subscribe to Call Waiting Caller ID service to
Purchase date ____________________________________________
receive Caller ID information.
Caller ID Error Message
Name of store ____________________________________________
•
The unit displays this message if it detects anything other
than valid Caller ID information during the silent period
after the first ring. This message indicates the presence of
noise on the line.
S
I
I
OLUTIONS
NTERFERENCE
NFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna (that is,
the antenna for radio or television that is "receiving"
the interference).
•
Reorient or relocate and increase the separation
between the telecommunications equipment and
receiving antenna.
•
Connect the telecommunications equipment into an outlet
on a circuit different from that to which the receiving
antenna is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
If these measures do not eliminate the interference, please
consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet,
"How To Identify and Resolve Radio/TV Interference
Problems. " This booklet is available from the U.S. Government
Printing Office, Washington, D.C. 20402. Please specify stock
number 004-000-00345-4 when ordering copies.
L
W
IMITED
ARRANTY
What your warranty covers:
•
Defects in materials or workmanship.
For how long after your purchase:
•
One year, from date of purchase.
(The warranty period for rental units begins with the first
rental or 45 days from date of shipment to the rental firm,
whichever comes first.)
What we will do:
•
Provide you with a new or, at our option, a refurbished
unit. The exchange unit is under warranty for the
remainder of the original product's warranty period.
How you get service:
•
Properly pack your unit. Include any cables, etc.,
which were originally provided with the product. We
recommend using the original carton and packing
materials.
•
"Proof of purchase in the form of a bill of sale or receipted
invoice which is evidence that the product is within the
warranty period, must be presented to obtain warranty
service. " For rental firms, proof of first rental is also required.
Also print your name and address and a description of the
defect. Send via standard UPS or its equivalent to:
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
•
Pay any charges billed to you by the Exchange Center for
service not covered by the warranty.
•
Insure your shipment for loss or damage. ATLINKS
accepts no liability in case of damage or loss.
•
A new or refurbished unit will be shipped to you freight
prepaid.
What your warranty does not cover:
•
Customer instruction. (Your Owner's Manual provides
information regarding operating instructions and user
controls. Any additional information, should be obtained
from your dealer.)
•
Installation and setup service adjustments.
•
Batteries.
•
Damage from misuse or neglect.
•
Products which have been modified or incorporated into
other products.
•
Products purchased or serviced outside the USA.
•
Acts of nature, such as but not limited to lightning damage.
Product Registration:
•
Please complete and mail the Product Registration Card
packed with your unit. It will make it easier to contact you
should it ever be necessary. The return of the card is not
required for warranty coverage.
Limitation of Warranty:
•
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY
APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO
VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS
USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE
A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF
THIS WARRANTY.
•
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT OR
ARISING OUT OF ANY BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. THIS
DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY
ARE GOVERNED BY THE LAWS OF THE STATE OF
INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
•
Some states do not allow the exclusion nor limitation of
incidental or consequential damages, or limitations on
how long an implied warranty lasts so the above
limitations or exclusions may not apply to you.
•
This warranty gives you specific legal rights, and you also
may have other rights that vary from state to state.
If you purchased your product outside the USA:
•
This warranty does not apply. Contact your dealer for
warranty information.
A
I
CCESSORY
NFORMATION
DESCRIPTION
MODEL NO.
PRICE*
Belt Clip
5- 2641
**
Headset
5- 2642
**
Replacement battery
5- 2522
**
Power Supply
5- 2639
**
Interchangeable color cover pack
(Red)
52643R
**
(Silver)
52643S
**
(Yellow)
52643Y
**
(Purple)
52643P
**
To place order, have your Visa, MasterCard, or
Discover Card ready
1-800-338-0376
.
and call toll-free
A shipping and handling fee will be charged upon
ordering.
We are required by law to collect appropriate sales tax
for each individual state, country,
and locality to which the merchandise is being sent.
Items are subject to availability.
*Prices are subject to change without notice.
Advertisement
