GE ZET1 Installation Instructions Manual page 5

Cutout for Single Built-In Oven
A1
ALLOW 11/16" FOR
OVERLAP OF THE
Allow 11/16"
OVEN OVER SIDE
(1.75 cm) for
EDGES OF CUTOUT
overlap of oven
over side edges
of cutout
21"
21"
(53.3 cm)
ALLOW A MINIMUM
Allow a minimum
OF 21" FOR CLEARANCE
of 21" (53.3 cm) for
TO ADJACENT CORNERS,
clearance to adjacent
DRAWERS, WALLS ETC.
WHEN THE DOOR IS OPENED. corners, drawers,
walls, etc. when
door is open
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 175 lbs. (79 kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
Installation Instructions
Cutout
Width
28 1/2" Min.
CUTOUT
28 5/8" Max.
WIDTH
(72.4 to
28 1/2" MIN.
72.7 cm)
28 5/8" MAX.
Opening
Between
THE OPENING
Inside Walls
Cutout
BETWEEN INSIDE
CUTOUT
Must Be
Height
WALLS MUST
HEIGHT
At Least
BE AT LEAST
27 1/4" Min.
27 1/4" MIN.
28 1/2"WIDE
28 1/2"
27 5/16" MAX.
27 5/16" Max.
(72.4 cm)
(69.2 to 69.3 cm)
Wide
RECOMMENDED
Recommended
CUTOUT
minimum cutout
Allow 1" (2.5 cm)
LOCATION
ALLOW 1" FOR
32 1/2"
location from
OVERLAP
minimum for
FROM THE
ON OVEN TOP
floor 32 1/2" (82.6 cm)
overlap of oven
FLOOR
AND BOTTOM
1
top and 1 ⁄
"
OF CUTOUT
4
(3.2 cm) overlap
of oven bottom
of cutout
CABINET
Cabinet WIDTH
30"
Width
30" (76.2 cm)
5"
5"
(12.7 cm)
JUNCTION BOX
Junction Box
LOCATION
Location
22" TO
22" (55.9 cm)
BOTTOM OF
to Bottom of
JUNCTION BOX
Junction Box
Suitable
Bracing
to Support
SUITABLE
Runners
BRACING
TO SUPPORT
RUNNERS
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.
This oven is not approved for
stackable or side by side installation.
5
Cabinet Width 30" (76.2 cm)
Recommended
Minimum
Cutout Location
from Floor 32 1/2" (82.6 cm)
Cutout Depth 23 1/2" (59.7 cm) Min.
Cutout Width 28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
Cutout Height 27 1/4" (69.2 cm) Min.
27 5/16" (69.2 cm) Max.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4"
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
C L
21 5/8"
21 5/8"
OVER CENTERLINE
(54.9 cm)
OF CABINET
Over Centerline
of Cabinet
Install a
2" x 4" or
EQUIVALENT
solid bottom
RUNNERS
or 2" x 4"
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout