Caple Wi6114 Instruction Manual
  1. Manuals
  2. Brands
  3. Caple Manuals
  4. Wine Cooler
  5. Wi6114
  6. Instruction manual
Caple Wi6114 Instruction Manual

Caple Wi6114 Instruction Manual

Slot-in wine cabinet
Hide thumbs Also See for Wi6114:
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction manual for slot-in wine cabinet
Model code: Wi6114
 
Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Wi6114 and is the answer not in the manual?

Questions and answers

Related Manuals for Caple Wi6114

Summary of Contents for Caple Wi6114

  • Page 1 Instruction manual for slot-in wine cabinet Model code: Wi6114   Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk...

  • Page 2: Important Safety Instructions

    The wine cellar should be installed in a suitable place in order to avoid touching the compressor with the hand. If the supply cord is damaged, it must be replaced by a Caple service agent or a similarly qualified person in order to avoid a hazard.

  • Page 3: Installation Instructions

    INSTALLATION INSTRUCTIONS Before using your wine cabinet • Remove the exterior and interior packing. • Before connecting the Wine cabinet to the power source, let it stand upright for approximately 12 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
  • Page 4 OPERATING YOUR WINE CABINET AND SETTING THE TEMPERATURE CONTROL Please use the cabinet within a ambient temperature of 5-32 If the ambient temperature is °C. higher than or lower than this temperature, it will cause temperature fluctuation in the cabinet, which may prevent it reaching 5-18 °C Controls •...
  • Page 5 Note • If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the Wine cabinet will not start. • When you use the Wine cabinet for the first time or restart the Wine cabinet after having been shut off for a long time, there could be a few degrees variance between the temperature you select and the one indicated on the LED readout.
  • Page 6 1. When open the door 90 degree, take out 2 screws (2) from lower door axis (3), remove the door (4), then pull out the door and door axis (Fig. A). 2. Put the door (4) safety and take out the plug (12) from top of door frame, unscrew 1 screw (11) at bottom and remove the door limit device (10), then install the Door limit device (10) at top of door frame, please use spare plug (12) to block the hole at top of door frame.

  • Page 7: Care And Maintenance

    Installation dimensions CARE AND MAINTENANCE Cleaning your wine cabinet • Turn off the power, unplug the appliance, and remove all items including shelves and rack. • Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water.

  • Page 8: Troubleshooting Guide

    Energy saving tips • The Wine cabinet should be located in the coolest area of the room, away from heat producing appliances, and out of the direct sunlight. PROBLEMS WITH YOUR WINE CABINET? You can solve many common Wine cabinet problems easily, saving you the cost of a possible service call.

  • Page 9: Humidity Maintenance System

    DEFROSTING/CONDENSATION Your wine cellar is designed with an “Auto-cycle” defrost system. When the RUN cycle is OFF, the refrigerated surface of the wine cellar (interior rear wall) defrosts automatically. The defrost water is channeled into a drain pan which is located at the back of the wine cellar next to the compressor from where it evaporates.

Table of Contents