Mitsubishi Electric XD470U Control Manual page 5

ITEM
RESET ALL
HORIZ.POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
SET UP
HOLD
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
UNPLUG DEVICE *
AUTO START *
REPEAT SETTING *
INTERVAL TIME *
TRANSITION EFFECT *
THUMBNAIL DISPLAY *
* XD435U only
• Some commands are not executed depending on the input signal. The operational restrictions same as those on
the menu setting are applied. Refer to "Menu operation" in the User Manual for more details.
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII '+' '–'
HEX 2Bh 2Dh
[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
from the PC, etc.
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' ' '
[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and
the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in
quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 53 0D
'0' '0' 'S' ' '
ASCII HEX
RSTALL 52h 53h 54h 41h 4Ch 4Ch -
HP 48h 50h
VP 56h 50h
FN 46h 4Eh
TRK 54h 52h
CIN 43h 49h
STU 53h 54h
HLD 48h 4Ch
HLB 48h 4Ch
HLE 48h 4Ch
CLP 43h 4Ch
CLW 43h 4Ch
UUD 55h 55h
UAS 55h 41h
URS 55h 52h
UIT 55h 49h
UTE 55h 49h
UTD 55h 49h
'0' '1' '2' '3'
30h 31h 32h 33h
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' '
VALUE
+ (increment), - (decrement)
+ (increment), - (decrement)
00 - 31
4Bh + (increment), - (decrement)
4Eh 0 (RGB), 1 (YC
55h 1 (OFF), 2 (3.75%), 3 (7.5%)
44h 0 (OFF), 1 (ON)
42h 00 - 99
45h 00 - 99
50h 00 - 63
57h 01 - 63
44h -
53h 0(OFF),1(ON)
53h 0(OFF),1(ON)
54h 0(5 sec.), 1(10 sec.),
2(30 sec.), 3(1 min.),4(3 min.)
00=NONE, 01=SLIDE IN ← , 02=SLIDE IN →
45h
03=WIPE ↓, 04=WIPE ↑, 05=WIPE → , 06=WIPE ←
07=SPLIT WIPE IN , 08=SPLIT WIPE OUT
09=SPLIT WIPE IN
11=BLIND ↓, 12=BLIND → , 13=BOX WIPE IN
14=BOX WIPE OUT, 15=DISSOLVE1, 16=DISSOLVE2
44h 0(OFF),1(ON)
'4' '5' '6' '7'
34h 35h 36h 37h
Status code from
the projector
'
Status code from
the projector
Status code from
the projector
'
5
C /YP P ), 2(AUTO)
B R B R
, 10=SPLIT WIPE OUT ↔
'8' '9'
38h 39h
Description
Command for setting the
AUTO POWER ON to ON
Command receipt confirmation
(Command echo back)
Description
Command for setting the
picture control
Command receipt confirmation
' (Command echo back)
Description
Command for checking
the TINT setting
Check result (+10)
,