Table of Contents
Advertisement
Installation
Instructions
[STEP 5] LEVEL REFRIGERATOR
All models
have 4-point
leveling.
The fl'ont
is
supported
by leveling
legs, the rear
is supported
by
adjustable
wheels.
Both
are accessible
fl'om
the fl'ont
of the refl'igerator.
• To level the back of the refl'igerator,
turn
the
7/16"
hex nut located
above
the fl'ont
wheels.
Turn
clockwise
to raise or counterclockwise
to lower
the
refl'igera
toi;
• For fl'ont
leveling,
use a 1-1/4"
oi)en-end
wrench.
• A(!just height
of refl'igerator
to match
installation
cutout
opening
83-1/2
to 84-1/2".
The
refl'igerator
should
be level and plumb
with cabinetry.
CAUTION:
The
rear
leveling
wheels
and
fl'ont
leveling
legs
are
limited
to a maximum
height
a_!justment
of l ". If the
installation
requires
more
than
84-1/2"
height,
the
installer
should
elew_te
the
refrigerator
on
a sheet
of
pl)_vood
or runnei_.
Cabineti
T trim
could
also
be
added
across
the
top
of the
opening
to shorten
the
opening.
If you
attempt
to raise
the
refrigerator
more
thm_
1", you
will damage
the
front
leveling
legs
mad the
rear
leveling
wheels.
PRUDENCE
i.es
roues
de
nivellement
arri&re
et les pattes
de
nivellement
avant
permettent
un r_glage
maximal
de 25 mm
(l po).
Si l'ouverture
pour
le r_fl'ig&'ateur
a une
hauteur
SUl)_riem'e
_'l 2,15
m (84-1/2
po),
l'installateur
doit
_lever
le r_fl'ig_rateur
sur
une
teuille
de contre-plaqu_
ou des
glissi&res.
11 est
_galement
possible
d'ajouter
des
baguettes
de
finition
des
placards
sur
le haut
de l'ouverture
afin
de la r_duire.
I.ever
le r_fl'ig&'ateur
de
plus
de
95 mm
(l po)
endommage
les pattes
de
nivellement
avant
et les roues
de nivellement
arri&re.
12
]STEP 6] ALTERNATE ANTI-TIP
PROCEDURE
The
refrigerator
must
be secured
to prevent
tipping.
The
aalti-tip
brackets
cammt
be used
on metal
wall
studs.
Use
this Alternate
Procedure
to secure
the
refrigerator
against
tip-over
whenever
metal
wall
studs
are encountered
and
there
is no soffit.
Side View
Top Case Trim
Install Four
1-1/2" DrywallScrews
ThroughTrimand IntoSoffit
or 3/4" Min. Wood Brace
• Raise
the
grille
panel
to access
case
trim.
• Use
a 3/16"
bit
to drill
fimr
evenly
spaced
clearance
holes
through
the
metal
top
case
trim.
• Use
a 1/16"
bit
to drill
to pilot
holes
through
the
metal
clearance
holes
and
into
the
wood
soffit.
The
holes
should
be
centered
in the
soltit
or a 3/4"
rain.
wood
brace.
The
brace
spanning
the
enclosure
must
be securely
tastened
to cabinets
on both
sides.
• Install
four,
1-1/2"
drywall
screws
into
the
pilot
holes.
[STEP 7] SECURE REFRIGERATOR
TO CABINETRY
X'_ henexer
possible,
perfom_
this step for anti-tip
security
or when
anti-tip
brackets
cannot
be used.
The refrigerator
must
be secured
to prevent
tipping.
• Raise
the
grille
panel
to access
case
trim.
• Drill
hole
in trim
and
drive
screw
through
the
trim
into
ac!jacent
cabinet.
• Follow
the
same
procedure
on
the
opposite
side.
A
DriveScrews
ThroughCase Trimand Into
AdjacentCabinets
Advertisement
Table of Contents
