Exp-1 & Ms-4; Exp-1 And - Fender Mustang Floor Advanced Owner's Manual

• Bypass Effect — (On/Off) Select "On" to bypass the effect current-
ly selected in the Expression Behavior menu when switching the
pedal to Volume mode or select "Off" to leave the effect active.
• Reset Parameter to Preset Value when Switching to Volume
Mode — (On/Off) Select "On" to return the Expression Mode
Parameter to the stored preset value when switching to Volume
mode. Select "Off" if you want the parameter be left set to the
position of the pedal when switching to Volume mode.
Pedal Calibration
Occasionally it may become necessary to calibrate the Mustang
Floor's expression pedal and/or an EXP-1 expression pedal con-
nected to the Mustang Floor, to reset the parameter range of the
pedal(s) to ensure consistent performance.
To calibrate the expression pedal and EXP-1 pedal:
1. (Optional) Plug an EXP-1 pedal into the "EXP-1 / MS-4" jack on
the back of the Mustang Floor using the included cable.
2. Turn the Mustang Floor off.
3. Press and hold the UTIL button on the Mustang Floor while
turning the Mustang Floor back on. Continue holding the UTIL
button down until it is no longer illuminated.
4. Rock the Mustang Floor expression pedal (and the EXP-1, if
connected), through the full range of motion between heel
and toe positions.
5. The Mustang Floor expression pedal and the EXP-1, if con-
nected, have been calibrated!
Pedal Tension
Occasionally it may become necessary to adjust the tension of the
axle nut on the expression pedal to increase or decrease the ease
of pedal movement.
To adjust pedal tension:
Pry off the circular "F" cap from the right side of the pedal with a
small flat blade screwdriver, then use a 10 mm socket wrench to
adjust the axle tension. Do not over-tighten the axle nut to avoid
damaging the pedal assembly.
EXP-1 & MS-4
Your Mustang™ Floor gives you the option of adding an
EXP-1/ MIDI
MS-4
USB
external EXP-1 expression pedal and an MS-4 four-
OUT IN
button footswitch for additional flexibility. Both the
EXP-1 and MS-4 can be connected together through the
EXP-1 / MS-4 jack on the back of the Mustang Floor.
6
M U S T A N G
10 mm
POWER
I
0
F L O O R
™
To use the EXP-1 and MS-4 simultaneously, plug the EXP-1 into
the Mustang Floor and then plug the MS-4 into the second jack
on the EXP-1.
EXP-1 Expression Pedal (P/N 2301050000)
Configure the EXP-1 expression pedal through the pedal menus
(see Pedal Menus, page 5). The EXP-1 only functions in Expression
mode when connected to the Mustang Floor. The green LED indi-
cates when the EXP-1 pedal is powered on and the red LED indi-
cates whether Expression mode is currently enabled.
MS-4 Four-Button Footswitch (P/N 0080996000)
The MS-4 footswitch display and LEDs show you much of the same
information as the Mustang Floor screen, so you can for example,
tune your guitar and select presets by watching the footswitch
without ever looking at the screen onboard the Mustang Floor!
The MS-4 allows you to:
• Select Quick Access presets (QA1/QA2/QA3)
• Select presets (up/down/bank)
• Bypass effects
• Activate the Tuner
The footswitch has three modes that are identified by the three
LEDs labeled MODE 1, MODE 2 and MODE 3. The footswitch also
has a Tuner mode which is indicated when all of the mode LEDs
are off.
To switch between modes, press the MODE button. To activate
Tuner mode, press and hold the MODE button.
• Mode 1—Select one of three Quick Access presets using the but-
tons labeled: QA1 / QA2 / QA3 (in line with the MODE 1 LED). The
number of the preset will appear in the display of the footswitch.
You can assign any preset to be a Quick Access preset in the
utility menus. (see Utility Menus, page 7).
• Mode 2—Select presets down/up, or in banks of 10, using the
buttons labeled: DOWN / UP / BANK (in line with the MODE 2
LED). The number of the preset will appear in the display of the
footswitch.