Footswitch Modes; Tap/Tuner - Fender Mustang Floor Advanced Owner's Manual

M U S T A N G

Footswitch Modes

Press the MODE button to switch between PRESET and
FX SELECT modes:
PRESET Mode
M U S TA N G
In PRESET mode the green LED lights up and the
bottom five footswitch buttons (0•5, 1•6, 2•7, 3•8, 4•9)
are used to select presets from the current bank of
five presets. Press the BANK/PRESET buttons to select
different banks of five presets to choose from, then
PRESET / FX SELECT
MODE
press one of the numbered footswitch buttons to
select a preset from the bank as displayed on screen.
Select Preset Banks
1 2
M U S TA N G
TM
PRESET / FX SELECT
INSERT STOMP
MODE BANK / PRESET
0 5 1 6
INSERT STOMP
Select Presets from the current Bank
FX SELECT Mode
M U S TA N G
In FX SELECT mode the red LED lights up and the
bottom five footswitch buttons (INSERT, STOMP,
MOD, DELAY, REVERB) are used to select/bypass
effects for the current preset (the INSERT button
selects/bypasses external effects connected to the
PRESET / FX SELECT
MODE
INSERT LOOP jacks). Press the BANK/PRESET buttons
to select presets up or down, one at a time.
1 2
Select Presets
M U S TA N G
TM
INSERT STOMP
PRESET / FX SELECT
MODE BANK / PRESET
0 5 1 6
INSERT STOMP
Select / bypass Effects
Each FX Select footswitch button will function only when an
effect is assigned to that category for the current preset. See
Effect Menus on page 4 to choose effects.
F L O O R
TM
UP
BANK
3
F L O O R
MOD

TAP/TUNER

2 7 3 8 4 9
MOD DELAY REVERB
F L O O R
TM
UP
BANK
3
F L O O R
MOD
TAP/TUNER
2 7 3 8 4 9
MOD DELAY REVERB
F L O O R
™
Use the TAP / T UNER button to:
•Tap in delay time or modulation rate effect settings
•Activate the on-board guitar tuner
TAP/TUNER
TAP Button
When either a delay or modulation effect is active, the LED next to
the TAP/TUNER button will blink in sync with the effect time/rate
setting (modulation rates can have up to 12 second intervals and
the LED may blink infrequently). If both a delay and modulation
AMP STOMP MOD
effect are active simultaneously, the LED will blink in sync with the
TAP/TUNER
HOLD TO EDIT
delay effect and the TAP/TUNER button will only control the delay
time setting (you can bypass the delay effect temporarily if you
want to use the TAP/TUNER button to set the modulation rate).
4 5
You can use the effect settings menus or Fender FUSE to set
delay time and modulation rates more precisely.
DELAY REVERB
Using TAP to set effect time/rate settings:
1. Select a delay or modulation effect that causes the TAP/TUNER
LED to blink, using the effects menus (see "Selecting Effects"
under Effects Menus, page 4).
2. Press the TAP/TUNER button rhythmically (twice minimum)
in time with the desired interval. If you press the TAP/TUNER
button only once, the interval will be set to the maximum
value. You can see the maximum/minimum values for the
current effect in the effect settings menu (see page 5).
Watch the actual time/rate TAP values change while you are
tapping them in, by opening the effect settings menu!
TUNER Button
The Mustang™ Floor has a built-in Tuner mode that displays a
AMP STOMP MOD
TAP/TUNER
HOLD TO EDIT
chromatic guitar tuner on screen.
To use the Tuner:
4 5
1. Press and hold the TAP/TUNER button until the Tuner screen
appears.
2
Strike any single string on your guitar and watch the screen.
The note of the string being tuned is displayed along with a
DELAY REVERB
fine tuning needle:
3. Turn the tuning peg on your guitar until the fine tuning needle
indicates the string is in tune, as shown above.
4. Press EXIT or TAP/TUNER to exit from the Tuner.
Tap / Tuner
UTIL
SAVE
EXIT
DELAY REVERB PEDAL
PUSH
UTIL
SAVE
EXIT
DELAY REVERB PEDAL
PUSH
3