TP-Link TL-SG1016DE User Manual
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Switch
  5. TL-SG1016DE
  6. User manual

TP-Link TL-SG1016DE User Manual

16/24-port gigabit easy smart switch
Hide thumbs Also See for TL-SG1016DE:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Installation Manual
TL-SG1016DE/TL-SG1024DE
16/24-port Gigabit Easy Smart Switch
REV1.0.1
1910010773

Advertisement

Table of Contents
loading

Related Manuals for TP-Link TL-SG1016DE

Summary of Contents for TP-Link TL-SG1016DE

  • Page 1 TL-SG1016DE/TL-SG1024DE 16/24-port Gigabit Easy Smart Switch REV1.0.1 1910010773...

  • Page 2: Fcc Statement

    Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3: Safety Information

    Safety Information When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself.

  • Page 4: Table Of Contents

    CONTENTS Package Contents ..........................1 Chapter 1 About this Guide......................2 Intended Readers ......................2 Conventions........................2 Overview of This Guide ....................2 Chapter 2 Introduction ........................4 Overview of the Switch ....................4 Main Features.......................4 Appearance Description ....................4 2.3.1 Front Panel ......................4 2.3.2 Rear Panel ......................5 Chapter 3 Login to the Switch.......................6 Login..........................6 Configuration ........................6...
  • Page 5 802.1Q PVID Setting ....................27 Chapter 6 QoS..........................29 QoS Basic........................30 Bandwidth Control ......................32 Storm Control......................33 Appendix A: Specifications ......................36 Appendix B: Configuring the PCs ....................37...

  • Page 6: Package Contents

    The following items should be found in your box: One 16/24-port Gigabit Easy Smart Switch One power cord Two mounting brackets and other fittings Installation Guide Resource CD for TL-SG1016DE/TL-SG1024DE switch, including: • This User Guide • Other Helpful Information Note: Make sure that the package contains the above items.

  • Page 7: Chapter 1 About This Guide

    The two devices of TL-SG1016DE and TL-SG1024DE are sharing this User Guide. For simplicity, we will take the operation on TL-SG1016DE for example throughout the configuration chapters. TL-SG1016DE and TL-SG1024DE just differ in the number of LED indicators and ports and all figures in this guide are of TL-SG1016DE.
  • Page 8 Chapter Introduction Chapter 3 Login to the Switch Introduces how to log on to the Web management page. Chapter 4 System This module is used to configure system properties of the switch. Here mainly introduces: System Info: View device information and define the device description.

  • Page 9: Chapter 2 Introduction

    Thanks for choosing the TL-SG1016DE/TL-SG1024DE 16/24-port Gigabit Easy Smart Switch! 2.1 Overview of the Switch The TL-SG1016DE/TL-SG1024DE 16/24-port Gigabit Easy Smart Switch is an ideal upgrade from an unmanaged switch, designed for Small and Medium Business networks that require simple network management.

  • Page 10: Rear Panel

    Link/Act No device is connected to the corresponding port. 2.3.2 Rear Panel The rear panel of TL-SG1016DE/TL-SG1024DE features a power socket and a Grounding Terminal (marked with ). Figure 2-3 Rear Panel of TL-SG1016DE Grounding Terminal: TL-SG1016DE/TL-SG1024DE already comes with Lightning Protection Mechanism.

  • Page 11: Chapter 3 Login To The Switch

    Chapter 3 Login to the Switch 3.1 Login 1) To access the configuration utility, open a web-browser and type the default address http://192.168.0.1 in the address field of the browser, then press the Enter key. Figure 3-1 Web-browser Tips: To log in to the switch, the IP address of your PC should be set in the same subnet addresses of the switch.
  • Page 12 Figure 3-3 Main Setup-Menu Note: Clicking Apply can only make the new configurations effective before the switch is rebooted. If you want to keep the configurations effective even the switch is rebooted, please click Save Config. You are suggested to click Save Config before cutting off the power or rebooting the switch to avoid losing the new configurations.

  • Page 13: Chapter 4 System

    Chapter 4 System The System module is mainly for basic settings of the switch, including six submenus: System Info, IP Setting, User Account, Switching, Monitoring and System Tools. 4.1 System Info On this page you can view the system information and define the device description. Choose the menu System→System Info to load the following page.

  • Page 14: User Account

    Figure 4-2 IP Address Setting The following entries are displayed on this screen: IP Address Setting DHCP Setting: Allows you to enable or disable the switch to serve as DHCP client. If DHCP client is enabled, the switch will obtain the IP address, subnet Mask and default gateway from the DHCP Server automatically;...

  • Page 15: Switching

    Figure 4-3 User Account Setting You are kindly suggested to retype the new password in "Confirm Password" box instead of copying in order to avoid mistakes. Note: 1. The length of user name and password should not be more than 16 characters using digits, English letters and underlines only.
  • Page 16 Figure 4-4 Port Setting The following entries are displayed on this screen: Port Setting Port: Select the desired port for configuration. It is multi-optional. Status: Allows you to enable of disable the port. “Enable" Indicates that the port is operational and "Disable" indicates the port is non-operational.

  • Page 17: Igmp Snooping

    Note: The switch cannot be managed through the disabled port. Please enable the port which is used to manage the switch. 4.4.2 IGMP Snooping Internet Group Management Protocol (IGMP) snooping is a multicast control mechanism, which can be used on the switch for dynamic registration of the multicast group. IGMP Snooping allows the switch to recognize the IGMP messages transmitted between network stations or devices and an IGMP host.
  • Page 18 For the newly joined member ports in a trunk group, their default setting of Port setting (Speed and Duplex, Flow Control), QoS will be configured the same as that of the first member port in the trunk group. The trunk member ports cannot be set as mirroring port. Before setting the trunk, its member ports should be divided to the same VLAN, and have the same PVID and drop the untagged packet rule.

  • Page 19: Monitoring

    Port: Select the port as the trunk group member. It is multi-optional. Clearing all the ports of the trunk group will delete this trunk group. Tips: Calculate the bandwidth for a trunk group: If a trunk consists of the four ports whose Speed/Duplex mode is 1000Mbps/Full Duplex, the whole bandwidth of the trunk group is up to 8000Mbps (2000Mbps * 4) because the bandwidth of each member port is 2000Mbps counting the up-linked speed of 1000Mbps and the down-linked speed of 1000Mbps.

  • Page 20: Port Mirror

    Link Status: Displays whether the port is link up or link down. TxGoodPkt: Displays the number of good packets transmitted on the port. The error packets are not counted in. TxBadPkt: Displays the number of error packets transmitted on the port. RxGoodPkt: Displays the number of good packets received on the port.
  • Page 21 Figure 4-8 Port Mirror The following entries are displayed on this screen: Port Mirror Port Mirror: Allows you to enable or disable the port mirror feature of the specified port. Mirroring Port: Select a port from the pull-down list as the mirroring port. Mirrored Port Mirrored Port: Select a port from the pull-down list as the mirrored port to monitor...

  • Page 22: Cable Test

    Ingress: Select whether to monitor the ingress traffic. When the ingress is enabled, the ingress traffic received by the mirrored port will be copied to the mirroring port. Egress: Select whether to monitor the egress traffic. When the egress is enabled, the outgoing packets sent by the mirrored port will be copied to the mirroring port.

  • Page 23: Loop Prevention

    Test Result: Displays the connection status of the cable connected to the port. The test results of the cable include “No Cable”, “Open”, “Short”, ”Open Short”, “Normal”, “Cro Cable” and “others”. Cable Fault Displays the error length (in meters) of the cable. Distance(m): Note: The test result is just for your reference.

  • Page 24: System Reboot

    Figure 4-11 Backup and Restore The following entries are displayed on this screen: Config Backup Backup Config: Click the Backup Config button to save the current configuration as a file to your computer. You are suggested to take this measure before upgrading.

  • Page 25: System Reset

    4.6.4 Firmware Upgrade The switch system can be upgraded via the Web management page. To upgrade the system is to get more functions and better performance. Go to http://www.tp-link.com to download the updated firmware. Choose the menu System→System Tools→Firmware Upgrade to load the following page.
  • Page 26 Figure 4-14 Firmware Upgrade Note: Don’t interrupt the upgrade. You are suggested to backup the configuration before upgrading. Please select the proper software version matching with your hardware to upgrade. To avoid damage, please don't turn off the device while upgrading. After upgrading, the device will reboot automatically.

  • Page 27: Chapter 5 Vlan

    Chapter 5 VLAN The traditional Ethernet is a data network communication technology based on CSMA/CD (Carrier Sense Multiple Access/Collision Detect) via shared communication medium. Through the traditional Ethernet, the overfull hosts in LAN will result in serious collision, flooding broadcasts, poor performance or even breakdown of the Internet.

  • Page 28: Mtu Vlan

    each of the other ports. Each VLAN contains two ports, the uplink port and one of the other ports in the switch, so the uplink port can communicate with any other port but other ports cannot communicate with each other. 2.

  • Page 29: Port Based Vlan

    Figure 5-3 MTU VLAN Configuration Note: The uplink port will form several VLANs with each of the other ports. Each VLAN contains two ports, the uplink port and one of the other ports in the switch, thus the uplink port can communicate with any other port but other ports cannot communicate with each other.

  • Page 30: 802.1Q Vlan

    The following entries are displayed on this screen: Port Based VLAN Configuration Port Based VLAN Enable or disable Port Based VLAN mode. Configuration: Enter the ID number of VLAN. It ranges from 2 to 32. VLAN ID: Displays the port number. Port: Click the check box to select the port of the VLAN.
  • Page 31 Figure 5-5 802.1Q VLAN Configuration To ensure the normal communication of the factory switch, the default VLAN of all ports is set to be VLAN1. VLAN 1 cannot be modified or deleted. The following entries are displayed on this screen: 802.1Q VLAN Configuration 802.1Q VLAN...

  • Page 32: 802.1Q Pvid Setting

    Tagged: Click the check box to configure the egress rule of the traffic on this port as tagged. The switch adds the tag header before sending the packet. Not Member: Click the check box to exclude the port from the current VLAN. 5.4 802.1Q PVID Setting PVID (Port Vlan ID) is the default VID of the port.
  • Page 33 802.1Q VLAN Port Setting Select: Select the desired port for configuration. It is multi-optional. Port: Displays the port number. PVID: Enter a PVID number for the port. When adding the tag header to the received untagged packet, the switch will automatically uses this PVID value as the VLAN ID of the added tag.

  • Page 34: Chapter 6 Qos

    Chapter 6 QoS QoS (Quality of Service) functions to provide different quality of service for various network applications and requirements and optimize the bandwidth resource distribution so as to provide a network service experience of a better quality. This switch classifies the ingress packets, maps the packets to four different priority queues and then forwards the packets according to Strict-Priority scheduling algorithms to implement QoS function.

  • Page 35: Qos Basic

    to four different priority queues. After that, the switch will preferentially send packets in the queue with higher priority, and only when the queue with higher priority is empty, packets in the queue with lower priority are sent. 2. 802.1P Based Figure 6-2 802.1Q frame As shown in the figure above, each 802.1Q Tag has a Pri field, comprising 3 bits.
  • Page 36 Figure 6-4 QoS Basic The following entries are displayed on this screen: Global Config QoS Mode: Select the desired QoS mode. • Port Based: The switch classifies the ingress packets and maps the packets to different priority queues based on which port the packets come from.

  • Page 37: Bandwidth Control

    and maps the packets to different priority queues based on the 802.1p priority field in the 802.1Q tag. Port-based Priority Setting Port: Select the desired port to configure its priority queue. It is multi-optional. Priority Queue: Specify the priority queue the packets from the port are mapped to.

  • Page 38: Storm Control

    The following entries are displayed on this screen: Bandwidth Control Setting Port: Select the desired port for bandwidth control configuration. It is multi-optional. Status: Allows you to enable or disable the bandwidth control function.. Rate(Kbit/sec): Select the rate for receiving/sending packets on the port. The packet traffic exceeding the rate will be discarded.
  • Page 39 Figure 6-6 Storm Control Setting The following entries are displayed on this screen: Storm Control Setting Port: Select the desired port for storm control configuration. It is multi-optional. Status: Allows you to enable or disable the storm control function. Total Rate: Select the rate for receiving packets on the port.
  • Page 40 Included Storm Select to filter broadcast/multicast/UL frame in the network, if the Type: transmission rate of the chosen packets exceeds the set rate, the packets will be automatically discarded to avoid network broadcast storm. It is multi-optional. • UL-Frame: If UL-Frame packets traffic exceeds the rate on the port, they will be discarded.

  • Page 41: Appendix A: Specifications

    Appendix A: Specifications IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-TX IEEE802.3ab 1000Base-T Gigabit Ethernet Standards IEEE802.3x Flow Control IEEE802.1p QoS IEEE802.1q VLAN Ethernet: 10Mbps HD, 20Mbps FD Transmission Rate Fast Ethernet: 100Mbps HD, 200Mbps FD Gigabit Ethernet: 2000Mbps FD 10Base-T: UTP/STP of Cat. 3 or above 100Base-TX: UTP/STP of Cat.

  • Page 42: Appendix B: Configuring The Pcs

    Appendix B: Configuring the PCs In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 2000. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. On the Windows taskbar, click the Start button, and then click Control Panel. Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window.
  • Page 43 The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Figure B-3 Select Use the following IP address. And the following items will be available. If the switch's IP address is 192.168.0.1, specify IP address as 192.168.0.x (x is from 2 to 254), and the Subnet mask as 255.255.255.0.

This manual is also suitable for:

Tl-sg1024de

Table of Contents