Sony NXL-IP55 Operation Manual page 28

Item
8. Analog Audio out Select
Analog out 1,2
Analog out 3,4
Analog out 5,6
9. Intercom Interface
4W / RTS/ Clear-Com
Termination
ENG
PROD
28
Menus
Description
When [Analog Audio Direction] is set to [Output], this selects the signal source
for Analog out 1,2. The selectable signals and the initial value differ depending
on the [Transmission Settings] and [Video Format] on the [Structure] page.
SDI in 1: Outputs the signal that corresponds to the input of HD SDI IN
connector 1.
SDI in 2: Outputs the signal that corresponds to the input of HD SDI IN
connector 2.
SDI in 3: Outputs the signal that corresponds to the input of HD SDI IN
connector 3.
Opposite SDI in 1: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 1.
Opposite SDI in 2: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 2.
Opposite SDI in 3: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 3.
–: Does not output audio.
Ch1,2 / Ch3,4: Selects whether to output Ch 1 and 2, or Ch 3 and 4.
When [Analog Audio Direction] is set to [Output], this selects the signal source
for Analog out 3,4. The selectable signals and the initial value differ depending
on the [Transmission Settings] and [Video Format] on the [Structure] page.
SDI in 1: Outputs the signal that corresponds to the input of HD SDI IN
connector 1.
SDI in 2: Outputs the signal that corresponds to the input of HD SDI IN
connector 2.
SDI in 3: Outputs the signal that corresponds to the input of HD SDI IN
connector 3.
Opposite SDI in 1: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 1.
Opposite SDI in 2: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 2.
Opposite SDI in 3: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 3.
–: Does not output audio.
Ch1,2 / Ch3,4: Selects whether to output Ch 1 and 2, or Ch 3 and 4.
When [Analog Audio Direction] is set to [Output], this selects the signal source
for Analog out 5,6. The selectable signals and the initial value differ depending
on the [Transmission Settings] and [Video Format] on the [Structure] page.
SDI in 1: Outputs the signal that corresponds to the input of HD SDI IN
connector 1.
SDI in 2: Outputs the signal that corresponds to the input of HD SDI IN
connector 2.
SDI in 3: Outputs the signal that corresponds to the input of HD SDI IN
connector 3.
Opposite SDI in 1: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 1.
Opposite SDI in 2: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 2.
Opposite SDI in 3: Outputs the signal that corresponds to the input of the
partner unit's HD SDI IN connector 3.
–: Does not output audio.
Ch1,2 / Ch3,4: Selects whether to output Ch 1 and 2, or Ch 3 and 4.
Selects the interface of the intercom system to be connected to the AUDIO/
INTERCOM connector.
4W / RTS / Clear-Com
When the interface is set to [RTS] or [Clear-Com], this selects whether to
terminate the ENG line.
ON: Terminates the line.
OFF: Does not terminate the line.
When the interface is set to [RTS] or [Clear-Com], this selects whether to
terminate the PROD line.
ON: Terminates the line.
OFF: Does not terminate the line.
Target
Y
Y
Y
Y
Y
Y
Y
Y
Y