Cycle Selection Charts; Canceling A Cycle; Changing A Cycle Or Setting; Adding Items During A Cycle - KitchenAid KUDI01IL Use & Care Manual

Cycle Selection Charts

Select the wash cycle and options desired. Or press START to
repeat the same cycle and options as the previous cycle.
NOTE: If the last cycle you completed was a rinse cycle, the
dishwasher will run the last full wash cycle and options that you
selected when you press Start.
If the power is off or the door is open for an extended period
of time, the Start button memory will default to the Normal
cycle with heated drying.
If you do not run the dishwasher daily, close the door to
maintain memory.
A " " shows what steps are in each cycle.
Temperatures indicate where extra heat is added.
Water usage is shown in U.S. gallons/liters.
This model meets the E
NERGY
efficiency.
Cycle time includes dry time. An asterisk ( * ) by the cycle time
indicates the cycle time might be longer depending on the
temperature of the water entering the dishwasher. The cooler the
water, the longer the cycle time. If the water is already hot
enough, the cycle time will be as shown.
Use this cycle for
heavily-soiled pots,
pans, casseroles,
regular tableware and
harder than normal
water conditions.
Pre- Main Rinse Rinse
Wash Wash
130°F 140°F
(54°C) (60°C)
Use this cycle for loads
with normal amounts of
food soil. (The energy-
usage label is based on
this cycle.)
Pre- Main Purge† Rinse
Wash Wash
120°F
(49°C)
Use this rinse cycle for
rinsing dishes, glasses,
and silverware that will
not be washed right
away.
Pre- Rinse Main Rinse
Wash Wash
A small amount of water is run through the pump to remove
†
soil particles between the main wash and final rinse.
S ® guidelines for energy
TAR
Use both detergent
dispenser sections.
Final Dry Time
Heated (min)
Rinse
89*
140°F
(60°C)
Use both detergent
dispenser sections.
Final Dry Time
Heated (min)
Rinse
79*
140°F
(60°C)
Do not use detergent
with this cycle.
Final Dry Time
Heated (min)
Rinse
10
Anytime during a cycle, press
Cancel glows. The dishwasher starts a 2-minute drain (if needed).
Let the dishwasher drain completely. The light goes off when the
dishwasher finishes the drain.
To stop the drain
You can press Cancel again to stop the drain immediately.
Remember to drain the dishwasher before starting a new cycle.
To clear the indicators
Press Cancel before starting the dishwasher to clear all options
and cycles.

Changing a Cycle or Setting

During the first minute of a cycle
Press a new cycle and/or options.
After the first minute of a cycle
1. Press
Cancel glows. The dishwasher starts a 2-minute drain (if
needed). Let the dishwasher drain completely.
2. Check the detergent dispensers. If the main wash cup has
Water
opened and the detergent washed away, refill the cups as
Usage
needed.
(gal/L)
3. Close the door.
6.9/26
4. Press a new cycle and/or options.
5. Press START.

Adding Items During a Cycle

You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
Water
Usage
1. Lift up the door latch to stop the cycle. Wait for the spraying
(gal/L)
action to stop before opening the door.
5.9/22.3
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5-second pause.
Water
Usage
(gal/L)
1.8/7

Canceling a Cycle

11