Table of Contents
Advertisement
Electrical ground is required. See
Electrical requirements.
DO NOT install dishwasher over
carpeted flooring.
Proper electrical, drain and water
supply lines must be available or
must be installed as specified within
shaded area to prevent interference
with dishwasher frame or other
components. See Electrical, Water
and Drain requirements. Plumbing
and wiring should not cross in
front of motor or dishwasher frame.
Corner
location
- 2" min.
door to cabinets
or wall
7
Cut 1" holes for water,,drain
Grommet
and electrical
lines within
required
for
shaded
area.
electrical
cable
hole cut in
)\
metal cabinets
23-112"
cabinet
7
min.
-~
D -
Figure 1
depth
Xi
-I-
33-7116" min.
to 35" max.
underside
counter
height
If 33-7116'
height
Is needed,
the leveling
legs
will have
to be removed
The unshaded
area must
be free of oioes.
drain hose or 'wires.
ountert
Product Damage
Protect dishwasher and water
lines leading to dishwasher
against freezing.
Failure to do so could
cause inlet valve, water lines
leading to dishwasher, water
lines in dishwasher and drain
to rupture.
Such ruptures are not
covered by the warranty.
For installations where the
dishwasher will be left unused and
subjected to freezing temperatures,
it must be prepared as outlined in
your Use and Care Guide.
/
IMPORTANT:
Observe
all
1
governing
codes and ordinances.
\
I
1
24" opening
width
I
23-7/6"'1
I
-26"
depth
Flgure 2
J
'Whisper
Quiet
insulation
compressed.
Tools and
materials needed
for installation:
Personal Injury Hazard
Avoid opening dishwasher
door before dishwasher Is
installed.
Dishwasher, before
it Is installed, may tip over
when door is opened, resulting
in personal injury or product
damage.
l
electric
drill
. shutoff
valve
- Phillips
. supply
line fittings
screwdriver
. 1, 3/E" NPT street
l
2 adjustable
wrenches
for
elbow (2 for
galvanized
line) OR
co
I!
per fittings
0
2 pipe
90" compression
elbow wtth 316" NPT
wrenches
for
at one end for
jl;,pp
Or iron
. ;;J,e;;;aIm
and
- pliers
detergent-resistant
l
Electrlcal wlring and
components must not contact
any plumbing material or drain
hose.
l
Electrical wiring, water supply
line and drain line must not
contact any exposed terminals
of dishwasher wiring.
l
Cabinet opening must
completely enclose sides, top
and back of dishwasher.
A
side panel and wood top are
available from your
KitchenAid dealer to install
your dlshwasher at the end of
a cabinet.
Failure to follow these
instructions
may result in
personal injury from exposed
wiring.
Parts supplied for
installation:
l
measuring
tape
hoseand
clam1
* flat-blade
OR 5/r,
c - 30 carper
screwdriver
tubing
ana rnur
d ""'XIS
- 3/4" nut driver
or
. liy,
5/a** r- UIJ soft
socket
wrench
copper
tu lbing if
L:-L ,---
wire cutters
HKJ~ loop drain is
needed.
(See Page 3.)
* level
. 3/4" strain relief -
* 1" drill bit or
. bushlna
hole saw
* l/8" drill bit
- tubing iutter
. oiae-ioint
2 countertop
anchor
screws
- square
~&mpotmd
'112" OD copper
. twist-on
wire
tubing
OR 316" pipe
connectors
. electrical
tape
Remove parts from package.
Check that all parts were included.
Page 2
Advertisement
Table of Contents
