Table of Contents
Advertisement
Electrical ground is required. S ee
Electrical requirements.
DONOTinstall d ishwasher over
carpeted flooring.
Proper e lectrical, drainandwater
supply linesmustbe available or
mustbeinstalled asspecified within
shaded areato prevent i nterference
withdishwasher frameor other
components. SeeElectrical, Water
andDrainrequirements. Plumbing
andwiringshouldnotcrossin
frontof motor or dishwasher frame.
Product Damage
Protect dishwasher
and water
lines leading to dishwasher
against freezing.
Failure to do so could
cause inlet valve, water lines
leading to dishwasher, water
lines in dishwasher
and drain
to rupture.
Such ruptures are not
covered by the warranty.
For installations where the
dishwasher will be left unused and
subjected to freezing temperatures,
it must be prepared as outlined in
your Use and Care Guide.
Electrical Shock Hazard
• Electrical wiring and
components
must not contact
any plumbing material or drain
hose.
• Electrical wiring, water supply
line and drain line must not
contact any exposed terminals
of dishwasher wiring.
• Cabinet opening must
completely enclose sides, top
and back of dishwasher.
A
side panel and wood top are
available from your
KitchenAId dealer to install
your dishwasher
at the end of
a cabinet.
Failure to follow these
Instructions
may result in
personal injury from exposed
wiring.
Page 2
33-7/16" min.
to 35"
max.
underside
counter height
If 33-7/16"
height is needed,
the leveling legs
will have
to be removed.
Figure 1
Corner location - 2" min.
door to cabinets or wall
Cut 1" holes for water, drain
Grommet
and electrical lines within
required for
shaded area.
electrical
cable
hole cut in
metal cabinets
23-1/2" min.
The unshaded area must
be free of pipes,
drain hose or wires.
IMPORTANT: Observe all
governing
codes
and ordinances•
24" opening width
cabinet
depth_.rl_-36_
counlert
height
m
m
i
.
,
33 7/8'
height
Figure 2
*Whisper
Quiet
insulation compressed.
Personal Injury Hazard
Avoid opening dishwasher
door before dishwasher
is
installed.
Dishwasher, before
it is installed, may tip over
when door is opened, resulting
in personal injury or product
damage.
Parts supplied for
installation:
2 countertop
anchor screws
Remove parts from package.
Check that all parts were included.
Tools and
materials needed
for installation:
• electric drill
• Phillips
screwdriver
• 2 adjustable
wrenches
for
copper fittings
OR2
pipe
wrenches
for
alvanized
or iron
ttings
• pliers
• measuring
tape
• flat-blade
screwdriver
• 3/4" nut driver or
socket wrench
wire cutters
• level
• 1" drill bit or
hole saw
• 1/8" drill bit
• square
• 1/2" OD copper
tubing OR 3/8" pipe
• shutoff valve
• supply line fittings
• 1, 3/8" NPT street
elbow 12 for
galvamzed line) OR
90 ° compression
elbow with 3/8" NPT
at one end for
copper line
• 9/16", ID heat- and
detergent.resistant
hose and clamps
OR 5/8", OD copper
tubing and fittings
• 10", 5/8" OD soil
copper tubing if
high loop drain is
needed.
(See Page 3.)
• 3/4" strain relief
• bushing
• tubing cutter
• pipe-joint
compo_Jnd
• twist.on
wire
connectors
• electrical
tape
Advertisement
Table of Contents
