Advertisement
QuickSpecs
Standard Features
Rack Airflow Requirements
Rack Airflow Requirements
Rack Airflow Requirements
Rack Airflow Requirements
Installation of Server into
Installation of Server into
Installation of Server into
Installation of Server into
Telco Racks
Telco Racks
Telco Racks
Telco Racks
HP Factory Express
HP Factory Express
HP Factory Express
HP Factory Express
Capabilities
Capabilities
Capabilities
Capabilities
Service and Support
Service and Support
Service and Support
Service and Support
Rack 10000 series Cabinets
The increasing power of new high-performance processor technology requires increased cooling efficiency for rack-
mounted servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to
be fully loaded with servers using the latest processors.
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to
CAUTION:
CAUTION:
CAUTION:
prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 830
square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit adequate airflow
(equivalent to the required 64 percent open area for ventilation).
Side: The clearance between the installed rack component and the side panels of the rack must be a
minimum of 2.75 inches (7 cm).
CAUTION:
CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement
CAUTION:
CAUTION:
ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.
NOTE:
NOTE:
NOTE:
NOTE: For additional information, refer to the Setup and Installation Guide or the Documentation CD provided with the
server, or to the server documentation located in the Support section at the following URL:
http://www5.hp.com/servers/proliantml350.
ML350 G3 rack model support: Support for all 2-post Telco racks requires the use of the rack kit and an additional option
kit from Rack Solutions. http://www.racksolutions.com/hp.
HP Factory Express gives you the flexibility to choose from a full menu of factory capabilities all in one manufacturing
facility, in one process, with one touch giving you full control and access to HP's World class manufacturing facility
anytime. This approach provides you the speed to deploy your IT needs, with total quality assurance, reliability, and
predictability to lower your total cost of ownership by letting HP install, rack, and customize your software and hardware
options for you.
HP Services provides a three-year, limited warranty, including Pre-Failure Warranty (coverage of hard drives, memory and
processors) fully supported by a worldwide network of resellers and service providers and lifetime toll-free 7 x 24 hardware
technical phone support. In addition, available service offerings include:
NOTE:
NOTE:
NOTE:
NOTE: Limited Warranty includes 3 year Parts, 3 year Labor, 3-year on-site support.
A full range of HP Care Pack packaged hardware and software services:
Installation and start up
Extended coverage hours and enhanced response times
System management and performance services
Availability and recovery services
NOTE:
NOTE:
NOTE:
NOTE: For more information, visit
Please see the following URL regarding Warranty Information For Your HP Products:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html.
For additional information regarding Worldwide Limited Warranty and Technical Support, please see the following URL:
ftp://ftp.compaq.com/pub/supportinformation/ejourney/176738.pdf.
NOTE:
NOTE: Certain restrictions and exclusions apply. Consult the Customer Support Center at 1-800-345-1518 for details.
NOTE:
NOTE:
DA - 11430
Worldwide — Version 38 — February 13, 2004
HP ProLiant ML350 Generation 3
HP ProLiant ML350 Generation 3
HP ProLiant ML350 Generation 3
HP ProLiant ML350 Generation 3
http://www.hp.com/services/carepack.
Page 7
Advertisement
