Page 2
1-800-543-5454 www.officezone.com OfficeZone THE O D 4000 PUNCH WITH OD 4300 PLASTIC THE OD 4000 PUNCH WITH O D 4300 PLASTIC COIL INSERTER MODULE AND THE O D 4200 COIL INSERTER MODULE AND THE O D 4400 WIRE CLOSER MODULE...
1-800-543-5454 www.officezone.com OfficeZone Station Binding Combo The Combo Binding Station is a base unit that supports three different binding modules. Each module attaches in a matter of minutes. The attachment procedure will be located in the module instructional section of this manual.
Page 6
1-800-543-5454 www.officezone.com OfficeZone Wire closer The wire closer is capable of binding books up to 1 - 1 / 8 " (28.6mm) thick. It uses wire sizes from 3/16 to 1 -1/4". It has an adjustable closing bar for the different size wires.
1-800-543-5454 www.officezone.com OfficeZone Coil Inserter Module Installation Instructions: Diagram 1 Procedure to attach the coil inserter onto the Combo Binding Station or the OD 4000 Punch. + Align the t w o threaded studs (1) that protrude from the coil inserter option into the two holes located on the right side of the Combo Binding Station or OD 4000 Punch.
1-800-543-5454 www.officezone.com OfficeZone Setup Instructions: Diagram 2a, 2b, 2c, 2d & 2e Determine the correct coil size. Use a coil that is at least 3/32 (2.5mm) larger than the book thickness for coil sizes up to 3/4" (2Omm). After 3/4”, use a coil size of at least 1/8" over the book size.
1-800-543-5454 www.officezone.com OfficeZone Diagram 2a Adjusting the paper stop. Place the book on top of the Combo Binding Station or the OD 4000 Punch with the right side of the book against the paper stop bracket. Adjust the paper stop (6) so the holes of the book hang over the edge of the Combo Binding Station or OD 4000 Punch.
1-800-543-5454 www.officezone.com OfficeZone Forward /off / reverse switch. The forward / off / reverse (8) switch has three positions. The center position of this switch is the off position and should be placed in this position when not using the machine. Press the left side (forward) of the switch and the coil will rotate into the book.
1-800-543-5454 www.officezone.com OfficeZone holes in the sheets or covers. Continue until the coil is past the left side of the book by about one or two coils. Diagram 2d Drive wheel stop screw. The drive wheel stop screw (12) will prevent the wheel from pressing to hard on the mandrel.
Page 12
1-800-543-5454 www.officezone.com OfficeZone Diagram 2e edge of the right hand side of the book. Open the cutter enough so that the end of the cutter enters the coil by about a 1/4" Make sure the cutter is level with the book before you cut. As you squeeze the cutters you may notice the coil wants to twist.
Page 13
1-800-543-5454 www.officezone.com OfficeZone Wire Closer Module Installation Instructions: Diagram 3 Procedure to attach the wire closer onto the Combo Binding Station or the OD 4000 Punch. Place the closer module on the backside of the Combo Binding Station or the OD 4000 Punch so the closer adjustment knobs are facing the front of the Combo Binding Station or the OD 4000 Punch and are pointing up.
Page 14
1-800-543-5454 www.officezone.com OfficeZone Coil Inserter Module Electrical Schematic (120 volt Power Entry Modul e NOTE: The motor is protected by a thermal overload located in the motor. It will reset automatically after the motor cools. This product has earned the UL Listing Mark and the UL Listing Mark for Canada.
1-800-543-5454 www.officezone.com OfficeZone Wire Closer Module 2) Installation Instructions: Diagram 3 Procedure to attach the wire closer onto the Combo Binding Station or the OD 4000 Punch. Place the closer module on the backside of the Combo Binding Station or the OD 4000 Punch so the closer adjustment knobs are facing the front of the Combo Binding Station or the OD 4000 Punch and are pointing up.
1-800-543-5454 www.officezone.com OfficeZone Setup Instructions: Diagram 4a, 4b, 4c & 4d a) Determine the correct wire size. Use the table below to determine the correct wire size for the book thickness. You can insert more sheets into the wire, but it may affect the appearance of your book.
1-800-543-5454 www.officezone.com OfficeZone c) Setting the closing bar height The closing bar is adjustable on each end allowing the operator to achieve a perfect close at each end of the book. Pull the handle on the closer all the way down and adjust both knobs (3) so the top edge (4) of the closing bar lines up with the line (5) next to the wire size you want to close.
1-800-543-5454 www.officezone.com OfficeZone Comb Opener Module 3) Installation Instructions: Diagram 5 Procedure for attaching the comb opener onto the Combo Binding Station or OD 4000 Punch. Place the comb opener module on the backside of the Combo Binding Station or OD 4000 Punch so the narrow section of the comb opener is facing the front.
1-800-543-5454 www.officezone.com OfficeZone a) Determine the correct comb size. Use the table below to determine the correct comb size for the book thickness. You can insert more sheets into the comb, but it may affect the appearance of your book. Covers are not included with the number of sheets column.