Advertisement
For aH cooktop
mode_s with three=wire
cable
from the cooktop:
1
Where local codes Do Not permit connect{ng
the frame-
ground
conductor
to the neutram (white) junction
box
wire. (Used for Canadian installations):
4-wire
cable
from
power
supply
Ungrounded
red w,_
_..._._
/jjaection
bo×
/__
-]1
J
'_black wires
bare or green
_"_¢_j_
1.D sconneot w,re .........
\
orcsA , ,ate,
pOWer
SUpply.
3-wire
cable
conduit
connector
2, Remove the junction
from cooktop
1o
box cover from the junction box inside the cabinet,
3, Connect the flexible, armored cable from the cooktop to the
2.
junction box using a U,L,- or CSAqisted conduit connector,
Tighten screws on conduit connector,
3,
4, Connect the two black wires together; then connect the two red
wires together using twist=on connector, (See Figure 1 ,)
5, Connect the green or bare ground wire from the cooktop cable
4,
to the grounded wire in the junction box or other grounded
connector using twist-on connector,
6, Put a twist-on connector on end of white wire, Do Not connect
5.
bare ground wire to neutrat (white) wire in junction box.
7. Replace the junction box cover,
Where local codes permit connecting
the frame-ground
conductor
to the neutrat (white} junction
box wire. (Not
used for Canadian
installations):
3owire
cable from
power
supply
red wires
/junction
bo×
G ro u n ded
twiat°oe
neutral
connector
Figure 2
white
wire
J
bare
or
/
green
wire
3=wire cable _J
U=L.- or CSA- listed
Disconnect
from
cooktop
conduit
connector
power supply,
Remove the junction box cover from the junction box inside
the cabinet,
Connect the flexible, armored cable from the cooktop to the
junction box using a U,L,=or CSAqisted conduit connector,
Tighten screws on conduit connector,
Connect the bare cooktop wire with the white wire; the two
red wires together; and the two black wires together using
twist=on connectors, (See Figure 2,)
Replace the junction box cover,
For air cooktop
models
with four=wire
cable
from the cooktop.
(These
cooktops
are manufactured
with white
[neutral]
power
supply
wire and a cabinet-connected
bare ground
wire factory=crimped
together.):
Where local codes Do Not permit connecting
the frame-
ground conductor
to the neutral (white) junction
box
wire: (Used for Canadian
installations):
4-wire
cable
from power
suppty
red wires
/junction
box
Ungroundedneutra_
_h_to
w_ros
_'_
\twist-on
Figure 3
bare or
connector
green
wires
_
black
wires
1o Disconnect
4-wire
cable
power supply,
from
cookto
\
U,L.- or CSAo listed
conduit
connector
2. Remove the junction
box cover from the junction box inside the cabinet.
3, Connect the flexible, armored cable from the cooktop to the
junction box using a U.L.- or C.S.A.qisted conduit connector.
Tighten screws on conduit connector.
4, Connect the two black wires together; then connect the two red
wires together using twist-on connectors. (See Figure 3.)
& Separate the factory-crimped bare and white cooktop cable wires.
6, Connect the two white wires together using twist-on connectors.
7. Connect the bare ground wire from the cooktop cable to the
grounded wire in the junction box or other grounded connector
using twist-on connector. (See Figure 3.)
Do Not connect bare ground wire to neutral (white) wire in
junction
box.
8, Replace the junction box cover,
Where local codes permit connecting
the frame-ground
conductor
to the neutrat (white) junction
box wire. (Not
used for Canadian
installations):
3-wire
cable from
junction
power
supply
box
_
._
Grounded
__
bUack
neutral
wires
Figure 4
white _
..//X,X,
wore
grounding
oven
cable
[
wires
-- factory
_j
crimped
/J
1, Disconnect
4-wire
cable
from cooktop
power supply.
2. Remove the junction
box cover from the junction box inside the cabinet,
3, Connect the flexible, armored cable from the cooktop to
the junction box using a U=L=- or C=S=A=qisted conduit
connector, Tighten screws on conduit connector,
4. Connect the two black wires together; the two red
wires together; and the factory=crimped bare and
white cooktop cable wires to the white (neutral) wire
in the junction box using twist=on connectors. (See
Figure 4.)
& Replace the junction box cover,
U.L.- or CSA-
tisted
conduit
connector
Advertisement
