Page 1
2- Instructions for removing the hard disk drive: a- Remove the two screws (Picture below, Item B) of the hard disk cover. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 1 of 13, MS...
Page 2
Disconnect the HDD flatcable from the mainboard by removing the caution label with a pair of tweezers and carefully unlocking the cable. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 2 of 13, MS...
1- Remove the two screws at the corner of the base (location shown in the picture). 2- Turn over the unit, open the LCD panel and remove the two hinge caps by shifting them sidewards. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 3 of 13, MS...
Page 4
<Esc> and <F1> keys, the <F7> and <F8> keys, and the <Pause> and <Page Up> keys. 1- Unlock the connector, free the keyboard cable and take away the keyboard. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 4 of 13, MS...
Page 5
3- Remove the harness cap that covers the cable leading from the mainboard to the LCD panel (see picture). You may want to use a flatbed screwdriver. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 5 of 13, MS...
Page 6
4- Remove the screw that secures the LCD connector. 5- Disconnect the LCD connector. 6- Take away the LCD panel from the base unit. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 6 of 13, MS...
Page 7
2- Carefully peel the display bezel of the LCD module and remove the cover latch. This latch consists of the LCD hook (metal), the LCD hook button (plastic) and LCD hook spring. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 7 of 13, MS...
Page 8
3- Remove the four screws that secure the LCD panel. 4- Remove the screw that secures the hinge on the right side and remove the hinge itself. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 8 of 13, MS...
Page 9
This allows you to take out the LCD screen together with the inverter. 6- To remove the Inverter disconnect the two cables that connect the screen to the inverter. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 9 of 13, MS...
Removing the Memory Module (if applicable) 1- Pull the memory latches outwards to release the memory module and take it out. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 10 of 13, MS...
1- Remove the four screws on the upper cover. 2- Turn over the unit and remove the two screws in the hard disk drive compartment. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 11 of 13, MS...
Page 12
4- Apply inward force to the four points indicated to release the upper cover. You might want to use a flatbed screwdriver to release the clips on the indicated positions from the inside. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 12 of 13, MS...
Page 13
Reassembly is the reverse of the disassembly process. Use care to insure that the cables and screws are returned to their proper positions. Disassembly/re-assembly instructions Easy Lite / Versa Lite Packard Bell NEC Europe, version 1.0, 18-05-99, Page 13 of 13, MS...