Related Manuals for Barco R9002031
Summary of Contents for Barco R9002031
- Page 9 APPROXIMATE WEIGHT WITH HD8 LENS - 67 KG CRT POINT R7626572 R7626575 1040 R7626576 R7627612 R7627615 R7627616 CRT POINT GRAVITY POINT ROTATION COVER 169.5 *SERVICE* 45.5 MAX 500 FRONT IR RECEIVER AIRFLOW FIXATION POINT *4 X M8* POWER SUPPLY BACK IR RECEIVER AIRFLOW AIRFLOW MAX 1076...
- Page 11 • • • • 11.5 cm green phospho...
- Page 12 • • • • • • •...
- Page 13 • • • • • •...
- Page 14 • • •...
- Page 15 • • ADJUSTMENT MODE • Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER> <EXIT> to return • Select with then <ENTER> <EXIT> to return BS6QCD8TÃ''† Proj. address : 001 Soft. Version : 5.00 Config.
- Page 16 • • • • PASSWORD MODE POWER UP MODE PASSWORD REQUIRED OPERATING MODE WHEN FOR ADJUSTMENT POWER IS SWITCHED ON PLAYING StdBY BAUD RATE TABLE TO COMPUTER PROJECTOR ADDRESS StdBY (sum) CODE SPEED MAIN POWER PROCESSOR CYC I 2 C SHORTED BLOCK MATCH RESERVED ERROR...
- Page 17 • Source 2 Fh= 15.6 kHz Fv= 50 Hz •...
- Page 18 OFF ON OFF ON...
- Page 20 'Ãr…vƒur…hy† &$ÃPu€ &$ à Pu€ $%à C“ PORT 2 POWE R / MAINS COMM. P ORT PORT 3 POR T 4/5 PORT 1 PROJECT OR MODE &$Ã6 €ƒ $%ÃC“ P O W E R / M A IN S • •...
- Page 21 6…‡Ã…‘‘‘‘‘‘‘‘‘ Tr…vhyÅÑ‘‘‘‘‘‘ • • • • • • • •...
- Page 22 • • &$Ã6 €ƒ $%ÃC“ P O W E R / M A IN S • •...
- Page 24 • • ' Ã ƒr …vƒur… hy † • &$ ÃPu € & $ÃP u€ PORT 4/5 PORT 2 P OWER / MAIN S COMM. PO RT P ORT 3 PO RT 1 PROJECT OR MODE • • •...
- Page 25 ' Ã r… v ƒu r… h y† &$ ÃPu€ &$ ÃPu€ $ % à C“ P O RT 4/ 5 PORT 2 POWER / MAINS COMM. POR T PORT 3 POR T 1 PROJ ECTOR MOD E L Q Y H U &$Âu€...
- Page 26 • • • • • • • • &$à ‚u €Ã‡ r …€ LQ YHU ' à ƒr…vƒur…hy† &$ÃPu € &$à Pu€ $ % à C“ POR T 4 /5 P ORT 2 P OW ER / MAINS COMM. P ORT P ORT 3 PORT 1 PROJECT OR MODE...
- Page 27 ' Ã r …v ƒ u r …h y† &$ à P u€ & $ÃP u€ $ % à C “ PO RT 2 POWER / MAIN S COMM. POR T POR T 3 PO R T 4/5 PORT 1 PR OJECTOR MODE ' Ã...
- Page 29 L e n s n u t L E N S E S 2xGr 4xGr 3xBl 2xGr 1xBl 3xGr 2xGr 2xBl 3xGr 2xBl 3xGr 2xBl 2xGr 4xGr 2xGr 3xBl 1xBl 3xGr 2xBl 2xGr 1xBl 1xGr 1xBl 1xGr 1xBl 1xBl 1xGr 1xBl TO P CO VER 1xGr...
- Page 30 NO USER ADJUSTABLE PARTS INSIDE THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO, • AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS • IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN. enter password...
- Page 31 • • • • • • • 1. LOOSEN THE NUT ON THE REAR OF THE GREEN LENS, ROTATE THE LENS BARREL TO FOCUS THE CENTER OF THE IMAGE, THEN TIGHTEN THE NUT 2. LOOSEN THE NUT ON THE FRONT OF THE GREEN LENS AND ROTATE THE FRONT SECTION OF THE LENS TO FOCUS THE CORNERS OF THE...
- Page 32 CONTRAST LEVEL IS REDUCED AND BRIGHTNESS INCREASED TO MAKE THE RASTER VISIBLE ON THE FACE PLATE OF EACH CRT. USE THE ARROW KEYS TO CENTER THE RASTER ON THE GREEN, RED AND BLUE CRT RESPECTIVELY <ENTER> to continue <EXIT> to return Forbidden area Projected raster CRT faceplate border...
- Page 33 CRT PROJECTION ANGLE ADJUSTMENT CRT PROJECTION ANGLE IS THE FIRST STEP OF STATIC CONVERGENCE ADJUSTMENT. IT IS CRITICAL THAT THE RASTERS ARE CENTERED ON THE CRT FACE PLATES PRIOR TO PERFORMING THIS STEP. <ENTER> to read more <EXIT> to return CRT PROJECTION ANGLE ADJUSTMENT DURING THIS PROCEDURE,...
- Page 34 PROJECTION ANGLE ADJUSTMENT Align crosshairs <ENTER> continue <EXIT> to return (SW1 > SW2) 370b...
- Page 39 • •...
- Page 40 Use the potentiometers on the G2-ADJ. module to set the screen grid voltage for Red, Green and Blue. Adjust until the LED on the corresponding output amplifier is turned off. <EXIT> to return • •...
- Page 42 é ê ç è é ê ç è • é ê • • • •...
- Page 43 • é ê • ç è é ê • ç è é ê • • • é ê • ç è é ê ç è é ê...
Need help?
Do you have a question about the R9002031 and is the answer not in the manual?
Questions and answers