Speaker Setup - Integra DTR-30.3 Instruction Manual

Component Video Input
If you connect a video component to a component video
input, you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player to
COMPONENT VIDEO IN 2, you must assign "IN2" to
the "BD/DVD" input selector.
Here are the default assignments.
Input selector
BD/DVD
VCR/DVR
CBL/SAT
GAME
PC
AUX
TV/CD
PORT
■
BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,
TV/CD, PORT
IN1, IN2:
Select a corresponding component video input to
which the video component has been connected.
- - - - -:
Select if you are using the HDMI output, not the
component video output, to output composite video
and component video sources.
Note
• If you connect a component (such as UP-A1 Dock with docked
iPod/iPhone) to the UNIVERSAL PORT jack, you cannot
assign any input to the "PORT" selector.
• The "TUNER" selector cannot be assigned and is fixed at the
"- - - - -" option.
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign "OPTICAL1" to the "TV/CD" input
selector.
Here are the default assignments.
Input selector
BD/DVD
VCR/DVR
CBL/SAT
GAME
PC
AUX
TV/CD
PORT
En
44
Default assignment
IN1
- - - - -
IN2
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
Default assignment
COAXIAL1
- - - - -
COAXIAL2
OPTICAL1
- - - - -
- - - - -
OPTICAL2
- - - - -
■
BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,
TV/CD, PORT
COAXIAL1, COAXIAL2, OPTICAL1,
OPTICAL2:
Select a corresponding digital audio input to which
the component has been connected.
- - - - -:
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in
page 43), the same HDMI IN will be set as
"HDMI Input" (➔
a priority in this assignment. In this case, if you want to use the
coaxial or optical audio input, make the selection in the "Audio
Selector" (➔ page 53).
• Available sampling rates for PCM signals from a digital input
(optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
• If you connect a component (such as UP-A1 Dock with docked
iPod/iPhone) to the UNIVERSAL PORT jack, you cannot
assign any input to the "PORT" selector.
• The "TUNER" selector cannot be assigned and is fixed at the
"- - - - -" option.

Speaker Setup

Main menu Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ ® Room Correction and Speaker
page 31).
Setup (➔
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the "Audio TV Out" setting is set to "On"
– "HDMI Control (RIHD)" is set to "On"
you're listening through your TV speakers.
Speaker Settings
If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
again (➔ page 31).
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
"Speakers Type (Front)" setting
hookup information, see "Bi-amping the Front Speakers"
page 15).
(➔
Note
• When bi-amping is used, the AV receiver is able to drive up to
5.1 speakers in the main room.
• Before you change these settings, turn down the volume.
(➔ page 56).
(➔ page 56) and
(➔ page 45). For