Integra DTR-30.3 Instruction Manual page 45

■
Speaker Impedance
(Australian models)
4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
6ohms:
Select if the impedances of all speakers are between
6 and 16 ohms.
Note
• (North American models) Speakers with an impedance of less
than 6 ohms are not supported.
■
Speakers Type (Front)
Normal:
Select this if you've connected your front speakers
normally.
Bi-Amp:
Select this if you've bi-amped your front speakers.
■
Powered Zone 2
No
Yes:
Zone 2 speakers can be used. (Powered Zone 2
enabled).
Note
• If the "Speakers Type (Front)" setting is set to "Bi-Amp",
Powered Zone 2 cannot be used.
• When the "Powered Zone 2" setting is set to "Yes", the
surround back or front high speakers cannot be used.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey 2EQ
Speaker Setup, please make sure manually that any THX
speakers are set to "80Hz(THX)" crossover.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the "Audio TV Out" setting is set to "On"
– "HDMI Control (RIHD)" is set to "On"
you're listening through your TV speakers.
■
Subwoofer
Yes
No
■
Front
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
®
Room Correction and
page 56).
(➔
(➔ page 56) and
■
Center , Surround , Surround Back
*1 *1
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
■
Front High
*1*2*4*6
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
Note
*1 "Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*2 If the "Surround" setting is set to "None", this setting cannot
be selected.
*3 If the "Surround" setting is set to anything other than "Full
Band", "Full Band" cannot be selected here.
*4 If the "Speakers Type (Front)" setting is set to "Bi-Amp", or
the "Powered Zone 2" setting is set to "Yes", this setting
cannot be selected.
*5 If anything else than "None" is selected in "Front High", this
setting is automatically set to "None".
*6 If anything else than "None" is selected in "Surround Back",
this setting is automatically set to "None".
■
Surround Back Ch
1ch:
Select if only one surround back speaker L is connected.
2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the "Surround Back" Setting is set to "None", this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz, 90Hz, 100Hz, 110Hz, 120Hz
Bypass:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency
of the LFE channel's low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Note
• If you're using THX-certified speakers, select "80Hz".
■
Double Bass
This setting is NOT set automatically by
®
Audyssey 2EQ Room Correction and Speaker Setup
(➔ page 31).
On
Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the "Subwoofer" setting is set to
"Yes", and the "Front" setting is set to "Full Band".
• If you're using THX-certified speakers, select "Off(THX)".
*2*3*4*5
En
45