C H A P T E R Preparing for Installation This chapter describes the equipment and site requirements for installing the Cisco uBR904 cable modem. The chapter contains the following sections: • Safety Recommendations • Site Requirements • Tools for Installation •...
Keep tools and Cisco uBR904 cable modem components away from walk areas. • Do not wear loose clothing, jewelry (including rings and chains), or other items that could get caught on the Cisco uBR904 cable modem. Fasten your tie or scarf and roll up your sleeves. •...
Electrostatic discharge (ESD) damage, which occurs when electronic cards or components are improperly handled, can result in complete or intermittent system failures. The Cisco uBR904 cable modem consists of a printed circuit board that is housed in a metal enclosure. Electromagnetic interference (EMI) shielding and connectors are integral components of the enclosure.
ESD strap is attached to an unfinished surface of the Cisco uBR904 cable modem. • Always place the Cisco uBR904 cable modem on an antistatic surface or in a static shielding bag. If you are returning the item to the factory, immediately place it in a static shielding bag.
, and keep the area around the 23° to 113°F (-5° to 45°C) chassis as free from dust as is practical. The following sections address the site environment requirements for the Cisco uBR904 cable modem. Preparing for Installation 2-5...
Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers and receivers in the Cisco uBR904 cable modem, and can even create an electrical hazard by conducting power surges through lines and into equipment.
Cisco uBR904 cable modem for digital data transmission. Coaxial cable tolerances for the transmission of two-way digital data are much lower than the tolerances for the transmission of downstream-only video.
The size of your networks and the distances between connections on the CATV network can affect the successful installation of a Cisco uBR904 cable modem. When preparing a site for network connections to the Cisco uBR904 cable modem, you must consider several factors related to the cabling: •...
Page 9
Installing the Cisco uBR904 Cable Modem at the Headend You can mount the Cisco uBR904 cable modem on an equipment shelf at the headend provided that the rack dimensions allow you to secure the router to the shelf, and the overall configuration permits safe installation and access.
• Operating humidity range: 5 to 95%, noncondensing. • Airflow: Keep the back, sides, and bottom of the Cisco uBR904 cable modem clear of obstructions and away from the exhaust of other equipment. Caution To prevent chassis overheating, never install the Cisco uBR904 cable modem in an enclosed rack or room that is not properly ventilated or air conditioned.
Follow these general precautions when planning your equipment locations and connections: • We recommend keeping the Cisco uBR904 cable modem off the floor and out of any area that tends to collect dust. • Follow ESD prevention procedures to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent equipment failure.
Install proper grounding to avoid damage from lightning and power surges. Tools for Installation Each Cisco uBR904 cable modem chassis is fully assembled at the factory; no assembly is required. However, you will need the following tools and equipment to install the cable modem: •...
Page 13
Making a Crossover Ethernet Cable Connection The RJ-45 receptacle supports standard straight-through and crossover Category 5 UTP (RJ-45) cables. Cisco Systems does not supply Category 5 UTP cables; these cables are available commercially. Figure 2-2 shows the RJ-45 receptacle and plug. Table 2-2 lists the pinouts and signals for the RJ-45 receptacle.
Configuration Information After you install the Cisco uBR904 cable modem, verify that all the hardware is operating properly, verify that the computer is configured for IP and DHCP services, and establish a connection to the headend, the Cisco uBR904 cable modem will be configured by software downloaded from the Cisco uBR7246 universal broadband router installed at the headend.
Page 15
Cisco uBR904 Cable Modem Installation Checklist If an error message is displayed on the uBR904, you can find its explanation in the Note Cisco Cable CPE Error Messages book, viewable online at www.cisco.com/univercd/cc/td/doc/product/cable/cab_modm/ubcmerrs.pdf . Cisco uBR904 Cable Modem Installation Checklist...
Page 16
Console screen displays correct hardware configuration (displayed after system banner) Site Log A site log provides a historical record of all actions relevant to the Cisco uBR904 cable modem operation and maintenance. Keep the site log in a common place where anyone who performs tasks has access to it.
Page 17
Site Log Table 2-5 Site Log Example Date Description of Action Performed or Symptom Observed Initials Preparing for Installation 2-17...
Page 18
Site Log 2-18 Cisco uBR904 Cable Modem Installation and Configuration Guide...