Audiovox XDNX1H1 Quick Start Manual

1 Pick a Spot for Your Radio Pick a Spot for Your Radio
Install the Dash or Vent Mount
Installing the Vent Mount:
You can use either the Dash Mount or the Vent Mount for your onyX, depending upon your vehicle and the 1 Locate a suitable vent in your vehicle which is strong enough to
location where you want to place your radio. hold the onyX and the PowerConnect Vehicle Dock. (Options 4
or 5.)
CAUTION! Make sure your radio isn't in a place where it could interfere with driver visibility or safe deployment
of the airbags. 2 If the vent louvers are recessed, you'll have to use the
extended vent hooks. The Vent Mount is assembled with the
IMPORTANT! When you install the chosen mount, do not yet attach the PowerConnect Vehicle Dock to the
short vent clamps, so you will have to remove the short clamps
mount. The cables must be attached prior to connecting the dock to the mount.
and install the extended clamps as shown below.
Installing the Dash Mount:
Remove End Cap
CAUTION: The adhesive used on the Dash Mount may be difficult to remove.
Do not install this mount on leather surfaces (contact your vehicle dealer if you
are unsure about your dash surface), and make sure the air temperature is at
Dash
least 60ûF (15ûC) during installation. If it's not at least 60ûF, turn on the heater
Mount
in your vehicle to bring the temperature up to 60ûF.
1 Locate a flat surface for the Dash Mount. (Options 1, 2, or 3.) Make
Option 1
sure there is ample room for the dock and radio when installed.
2 Set the orientation of the mount before adhering it. Loosen the
Slide Extended Vent Clamps In
knob and adjust the adhesive foot for the location you selected:
• Option 1 & Option 3 I II
should be oriented
as I.
• Option 2 should be
oriented as II.
3 The dock mounting plate can be tilted in different directions.
Adjust as necessary for your particular vehicle. When the 3 Push the Vent Mount onto the vehicle vent as shown (1) until
hooked on the rear of the vent louver (2).
orientation is correct, tighten the knob.
Option 2
4 Rest the foot against the bottom of the vent (2). If necessary,
Knob Adhesive Foot Dock Mounting Plate
adjust the tilt of the Vent Mount by repositioning the foot to a
different tilt adjustment hole (3).
PUSH
4 Clean the surface with the alcohol preparation
pad, and let it dry thoroughly.
Foot
5 Peel off the adhesive liner. Position, press, and
hold the Dash Mount in place for 30 seconds. Option 3
IMPORTANT! Allow the Dash Mount adhesive to cure (dry) for a minimum of
2-4 hours before using the mount. The best adhesion occurs after 24 hours.
2 Install the Magnetic Mount Antenna
(continued)
Mount the Magnetic Mount Antenna
Extended Vent Clamps Choose the best location for the antenna considering your vehicle type. Refer to the antenna
placement tips and cautions in the User Guide beginning on page 22 .
• Sedan or Coupe: We recommend mounting the antenna just above either the front windshield
or the back window.
Short Vent • Pickup Truck: We recommend mounting the antenna just above the front windshield.
Clamps
• Convertible: We recommend mounting the antenna at the leading edge of the trunk.
• SUV: We recommend mounting the antenna at the rear of the roof.
Slide Short Vent Clamps Out
CAUTION! STOP and read the more specific instructions in the User Guide for all
Vent Mount types of vehicles — or get someone who knows vehicles to help — if you don't
understand what to do. You might accidentally do damage to your vehicle.
Option 4 Feed the antenna wire under the rubber molding around the front or rear
windshield, and into the seal around the trunk or door. For a convertible, the cable
can be routed directly into the trunk.
TIP! Use a tool like a blunt plastic putty knife, a credit card, a plastic knife, or a
similar blunt tool to help hide wires along the windshield trim.
Replace End Cap
Hide the Magnetic Mount Antenna Cable Inside the Vehicle
The best place to hide your antenna cable depends on your type of vehicle.
When the antenna is mounted at the rear of the vehicle, it's usually easiest to run
the cable from the rear to the front toward the radio by routing the cable along
Option 5 the interior trim where it meets the carpet, gently pushing it behind the edges of
the trim. Bring the cable out from the trim and route it under the carpet toward
the dashboard.
When the antenna is mounted at the front of the vehicle, bring the cable into the
rubber weather stripping around the door to the bottom of the door opening.
Bring the cable out of the weather stripping and route it under the carpet toward
the dashboard.
1 2 3
Coil any excess cable in a hidden location, such as under the carpet, keeping it
away from any vehicle pedals or controls. Secure the excess cable with wire ties.
Dash
Dash Dash
Plug the antenna into the silver ANT connection on the rear of the dock.
HOOKED
Vent Vent
Vent
Louver
TIP! Avoid damaging or compromising the window, door, and trunk seals.
TIP! For more help, refer to the detailed antenna cable routing instructions for
your type of vehicle, in the User Guide beginning on page 25 .
3 Connect the Audio to Your Vehicle's Stereo
Decide How to Connect
You will listen to onyX through your vehicle's stereo system or FM radio. First, onyX must be receiving the XM signal.
Ensure your vehicle is outside with the antenna having a clear view of the sky. Your audio connection options are:
• Best: Use the Aux In Cable if your vehicle's stereo system has
an auxiliary input connection. Plug one end of the cable into the
green AUDIO connector on the PowerConnect Vehicle Dock and
the other end into the vehicle stereo system's auxiliary input jack.
Set the stereo system to play from the auxiliary input source.
AUDIO ANT
• Better: Use a Cassette Adapter if your vehicle has a built-in
cassette player. Cassette Adapters are sold separately. Plug
the Cassette Adapter into the green AUDIO connector on the
PowerConnect Vehicle Dock. Insert the Cassette Adapter into
the vehicle's cassette deck. Set the stereo system to play from
the cassette source.
• Good: Use the PowerConnect feature in the onyX. PowerConnect plays the audio through your vehicle's FM radio.
When you have finished step 4 (below), you'll first need to find an available FM channel in your area, and then you
need to ensure that the onyX and your vehicle's FM radio are tuned to the same available FM channel. (Step 5)
• Best: Use an FM Direct Adapter (FMDA) if none of the above three audio connection options works in your
vehicle. The FMDA needs to be installed by a professional installer and directly connects the onyX to your
vehicle's FM radio.
TIP! Refer to your vehicle's owners manual to find the location of the auxiliary input jack, or consult the vehicle
dealer. To learn more about purchasing a Cassette Adapter or FMDA, check with the retailer where you bought your
onyX or go to xmradio.com/accessories.
4 Finish the Installation and Power On
Connect the PowerConnect Power Adapter
Insert the PowerConnect Power Adapter into your vehicle's cigarette lighter or power
adapter socket. Then plug it into the red PWR connector on the rear of the dock.
AUDIO ANT PWR FM
Attach the Dock to the Mount
Wire Guide
and the Radio to the Dock
Attach the PowerConnect Vehicle Dock
to the mount that you selected. Utilize
the wire guide at the rear of the dock to
help organize the wire and cables, and
make your installation neater.
Place the onyX into the dock. Press the
Power button to turn it On.
5 PowerConnect
If you have connected the audio in step 3 using the Aux In Cable or Cassette Adapter, continue with step 6.
Tune the onyX and Vehicle FM Radio to the Same FM Channel
1 Find an Available FM Channel in Your Area
Audio Quality GOOD BETTER BEST
An available FM channel is one that's not being used by an FM radio station in your area. When you
FM Direct Adapter (FMDA) tune your FM radio to an available channel, you should only hear static or silence – not talk or music.
Aux In Cable We recommend one of the following methods to find an available FM channel:
a. Use the SIRIUS | XM FM Channel Finder at www.xmradio.com/fmchannel. Go to the website and
Cassette Adapter
enter your zip code. The Channel Finder will suggest a list of available FM channels in your area.
PowerConnect
For convenience, write down or print out the list.
PWR FM
OR
b. Manually tune through your local FM channels on your vehicle's FM radio. Locate and create a list of
channels that aren't being used by any FM radio station. Write down the list. Once you have created
your list of available FM channels, you will need to find the one that provides the best match for onyX.
AUDIO ANT PWR FM
TIP! You'll need to use the 'Manual' tune function on your vehicle's FM radio to tune through every FM channel
one-by-one. Turn on your vehicle's FM radio. Start at 88.1 and use the 'Manual' tune function on your vehicle's FM
radio to tune through each FM channel one-by-one (88.1 followed by 88.3 etc.) to locate channels that aren't being
used by a local FM radio station. Write down each FM channel that has only static or silence on it, until you reach 107.9.
2 Tune your Vehicle's FM Radio
a Pick the first FM channel on your list.
b Turn on your vehicle's FM radio (if you have not already done so) and tune it to this FM channel.
3 Set Your onyX to Transmit on the Same FM Channel
a Press menu.
b Press to scroll to and highlight FM Settings and press the Select button.
c FM Channels will be highlighted. If it is not highlighted, press
and highlight FM Channels. Press the Select button.
d Press to scroll to and highlight the storage location FM 2 and press the
Select button.
e Tune to the available FM channel you found in step 1. Press and
in steps of .2, i.e., 99.3 to 99.5. Press and to tune in steps of 1, i.e.,
99.3 to 100.3. Press the Select button to select the FM channel.
AUDIO ANT PWR FM
f Start Using will be highlighted. Press the Select button.
g The FM channel you selected will be confirmed on the display screen and
the onyX will tune to that FM channel.
h You should hear XM through your vehicle's radio when onyX is tuned to
channel 1. If you are satisfied with the sound quality, you're done.
99.3
menu
FM
jump
1 2 3 4 5 6 7 8 9 0 direct
MATCH FM CHANNELS
PowerConnect
(continued)
4 You May Need to Try Other FM Channels on Your List
If the chosen FM channel doesn't work well for you, work down the list of FM channels until you find
one that allows you to hear XM clearly. Each time, you will need to tune your vehicle's FM radio and
onyX to the same FM channel.
TIP! You may find an FM channel with static or silence that does not work with onyX. It is possible that some type
of inaudible interference is present that prevents reception of the onyX broadcast. Your only options are to use
another FM channel or a different audio connection method.
NOTE! If you are using the Vehicle Dock from the Universal Xpress Car Kit instead of the
PowerConnect Vehicle Dock which came with your onyX, you will have to complete some
additional instructions before you can set onyX to transmit on an FM channel. Refer to
"Using the Vehicle Dock From the Universal Xpress Car Kit" on page 96 of the User
Guide, and complete the instructions. The audio connection will be through your
vehicle's FM radio, but it is not PowerConnect.
6 Activate
Activate Your Service
Before you can enjoy Commercial-Free Music, plus Sports, News, Talk & Entertainment, you need to activate
your onyX.
1 Make sure your onyX is properly installed, turned on, and receiving the XM signal so that you can
FM Channels
hear the audio on channel 1.
FM 1 97.9 current
FM 2 _ _ _ 2 Make a note of your XM Radio ID. You can find it on channel 0, on a label on the bottom of the gift
FM 3 _ _ _ box, and on the label on the back of your onyX.
to scroll to TIP! If the signal reception is
FM 4 _ _ _ NOTE! The XM Radio ID does not use the letters I, O, S, or F.
low, check to see if the
FM 5 _ _ _
antenna's view of the sky is
3 Activate your service: blocked by a tree, a building, a
Edit FM Channel 2 bridge, or by anything on the
• Online: Go to www.xmradio.com and click on "ACTIVATE
99.3 FM vehicle roof such as a roof rack
to tune RADIO" in the top right corner or luggage container, etc. Adjust
OR until you are receiving a good
signal.
• By phone: Call 1-800-XM-RADIO (1-800-967-2346)
Press arrow keys to tune
To check the signal, press menu.
and Select to confirm Press to scroll to and
TIP! You can follow the built in activation highlight Signal Indicator and
FM Channel 2 wizard in your onyX. If your radio has not Welcome press the Select button.
Start Using The next few screens will help Signal Indicator
been activated, press menu and the first item
you activate your satellite radio.
in the list will be Activate Radio. Press the
Edit Channel Please press Select to continue
SATELLITE
Select button. A series of screens will guide with the activation of your radio,
or press menu to cancel
you through the activation process. Follow the
activation at this time.
instructions on each screen. Press the Select TERRESTRIAL
button to advance to the next screen, or Press Select to continue
menu to cancel the activation process.
4 When your service is activated, your onyX will receive all channels to which you have subscribed. At
this time, if you press or , you can scroll and tune other channels. Activation usually takes 10
to 15 minutes, but may take up to an hour. We recommend that your radio remain on until activated.