Before operating this machine, please read the entire manual thoroughly. The 3M Digital WallDisplay Systems are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could dam- age the projector or peripheral equipment and/or create a potentially unsafe operating condition.
Page 8
• Do not apply force to the projection arm. This may cause permanent damage to the unit or may cause personal injury. • Do not manually open or close the projection arm while the 3M Digital WallDisplay is in operation. • The 3M Digital WallDisplay’s projection arm is motorized, and extends 42˝ (106 cm) from the installation while in use.
3M™ Digital WallDisplay Introduction Product Safety Label The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention. fro m 3 M Wall Display Save These Instructions The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay.
3M™ Digital WallDisplay Trademarks The 3M logo and 3M are registered trademarks of 3M Company. Vikuiti is a trademark of 3M Company. Microsoft, Windows, Windows NT, Word, Excel, PowerPoint, Internet Explorer, and NetMeeting are either reg- istered trademarks or trademarks of the Microsoft Corporation in the United States and/or other countries.
Standard Projection and Dry-Erase *The Copyboard feature allows you to print notes written on the 3M Digital WallDisplay to an attached printer. (PCL3 compatible printer required. See list in Appendix.) ** The Digital Whiteboard feature allows you to capture notes written on the 3M Digital WallDisplay with an attached computer or use the 3M Digital WallDisplay as an interactive display for a computer.
What’s Next? After the 3M Digital WallDisplay has been installed in your meeting room, you are ready to set it up. Please read this guide thoroughly before operating your new 3M Digital WallDisplay. Be sure to check our web site (www.3M.com/walldisplay) regularly for updates and supplemental information.
System Setup Connecting to Various Equipment It only takes a few minutes to connect the 3M Digital WallDisplay to your computer, VCR, DVD player, video conference unit, or other devices. The connection panel is located underneath the bottom right corner of the 3M Digital WallDisplay, under the Connection Panel Door.
2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the 3M label. This should stay on at all times. Now the 3M Digital WallDisplay is in standby mode. The large oval On/Off Button will be backlit amber after several seconds.
On/Off Button will flash red. The fan will continue to run for approximately five minutes to cool the unit. Note: If the 3M Digital WallDisplay will not be moved or disconnected, leave the Master Power Switch on for your convenience.
Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover.
3M™ Digital WallDisplay Forward Keypad Power Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn off the sound. Press again or press the Volume + or - buttons to restore sound.
Menu Navigation Most adjustments and settings are available in the main menu and sub-menus. To navigate and make adjustments, use the 3M Digital WallDisplay’s Menu Keypad button or the remote control’s Menu and Disk Pad buttons. MENU KEYPAD Colorful—Bright Slider The Colorful—Bright slider adjusts the brightness, contrast, and color saturation levels simultaneously.
The Input options are: Computer (VGA Input), DVI-D, S-Video, Comp. Video (RCA Video Input), and No Signal. An Input option is available to select when an active video source is connected to the 3M Digital WallDisplay input connection. To set the Input Select menu: 1.
Selects which language to use for onscreen commands. (Default language is English.) It cycles between English, German, Spanish, Italian, and French. Auto Shutoff Will automatically turn off the 3M Digital WallDisplay within the time desired. (Default time is 0 minutes.) Auto Switch When an input source is lost or disconnected, Auto Switch automatically detects and switches to the next available input source.
Maintenance General Maintenance For general cleaning of the screen and exterior of the 3M Digital WallDisplay, use a damp cloth or dry cleaning cloth such as the 3M High Performance Cleaning Cloth. Standard dry-erase cleaners may be used on the dry-eraseable screens, such as Sanford...
Maintenance 3M™ Digital WallDisplay Lamp Replacement To reduce the risk of electrical shock, always turn off the 3M Digital WARNING WallDisplay unit and disconnect power cord before changing lamp. 1. Turn the power off and disconnect the power cord from the outlet.
Page 32
• A potential hazard may exist in the rare case of lamp rupture. Please have CAUTION a 3M Digital WallDisplay dealer replace a ruptured lamp. • The lamp is extremely hot during normal operation. Before replacing the lamp, wait at least 45 minutes after last operation.
Replacing the 3M Digital WallDisplay screen is very simple. 1. Turn off the 3M Digital WallDisplay and disconnect the power cord from the wall outlet. 2. Remove the right and left side bezels. There are two ways to remove it. Either snap it off or insert a screwdriver into the notch located on the sides of each bezel, near the top.
Onscreen Messages Message Meaning No input is detected 3M Digital WallDisplay is not receiving a signal from an external source. Check the cable connections and verify power is on and external source is working. Please change the lamp The lamp has 1400-1499 hours on it and needs to be changed.
The contents of this manual are subject to change without prior notice. 3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.
Page 40
3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.